Selecon PAC51380V Manuel utilisateur

Version 1.3: January 2004

80V POWER SYSTEM

ELECTRONIC TRANSFORMER

OPERATION MANUAL

There are important set-up / operational instructions which must be

followed to ensure the safe and effective operation of your 80V

system.

Read this manual carefully before installing the system.

This manual covers the following models:

PAC51380V 80V 5.5°~ 13°Zoomspot Pacific

PAC122880V 80V 12°~ 28°Zoomspot Pacific

PAC143580V 80V 14°~ 35°Zoomspot Pacific

PAC235080V 80V 23°~ 50°Zoomspot Pacific

PACFB80V 80V Fixed beam Pacific

PAC9080V 80V 90°Fixed beam Pacific

This manual concerns the operation of the 80V Power System only. For

instructions on the operation of the Pacific luminaire fixture, please also

refer to the additional instruction sheet.

THANK YOU FOR PURCHASING A SELECON PACIFIC LUMINAIRE. WE HAVE DESIGNED THIS

LUMINAIRE TO PROVIDE YOU WITH A SUPERIOR FITTING IN PERFORMANCE, DESIGN &

ENGINEERING. WE ARE CONFIDENT THAT IT WILL PERFORM TO YOUR EXPECTATIONS FOR

MANY YEARS TO COME.

Caution!

Installation is entirely at your risk. Read this manual from cover to cover before attempting

installation. Do not attempt installation unless you are suitably qualified. If you do not understand

a point in this manual, don’t guess. Don’t take short cuts. If in doubt, stop! Contact Selecon or

one of its authorised distributors for advice. Don’t be afraid to ask for help.

IMPORTANT NOTE: Before discarding the packaging, ensure you have the mounting bolt

set, and high-temperature lens tube locking knob.

Pacific 80V Manual 2

Important!

Read this manual from cover to cover before attempting to install, operate or maintain the luminaires to

which it relates. It contains important installation, operating, maintenance and safety procedures. The

customer must strictly comply with them.

Along with such procedures mentioned in this document, the customer should also observe such other

procedures generally applicable to lighting equipment.

Follow the instructions in this manual carefully. Selecon accepts no responsibility if the customer fails to

do so.

For each customer, operating conditions will vary, sometimes greatly. Such variations may affect the

luminaires’ performance. Selecon has no control over the customer’s unique operating environment.

Hence, Selecon makes no representations or warranties concerning the luminaires’ performance under

the customer’s actual operating conditions. All operating parameters must be validated for each customer

application by the customer’s technical experts.

If the customer does not follow the installation, operating, maintenance and safety procedures in this

manual, as well as those generally applicable to lighting equipment, the luminaire may not perform as

expected. More seriously, it may cause property damage, personal injury or other losses.

Selecon accepts no liability for direct, indirect, incidental, special, or consequential damages resulting from

the customer’s failure to follow the installation, operating, maintenance and safety procedures in this

manual or those generally applicable to lighting equipment. The foregoing limitation extends to damages

for personal injury, property damage, loss of operations, loss of profits, loss of product or loss of time,

whether incurred by the customer, the customer’s employees or a third party.

Selecon used all due care in preparing this manual. However, Selecon accepts no liability for errors or

omissions. Selecon reserves the right to change the specifications of its luminaires, or the information in

this manual, without necessarily giving its customers notice thereof.

Installation, operation and maintenance are entirely at the customer’s risk.

Selecon’s luminaires should be installed, operated and maintained by suitably qualified personnel. Such

personnel should have previous experience with lighting equipment as well as general electrical

experience.

This manual is intended to provide general guidance to such suitably qualified personnel. For specific

guidance and technical support, contact Selecon or its authorised representative.

Information in this manual shall not be deemed a warranty, representation or guarantee concerning a

luminaires’ suitability or fitness for a specific purpose.

Subject to the right to use its luminaires, Selecon does not convey any right, title or interest in its

intellectual property, including, without limitation, its patents, copyrights and know-how.

The Pacific Power System is a new concept in tungsten halogen luminaires.

Please read this information carefully to ensure that you are fully conversant with

its operation.

Safety Warnings.........................................................................................................................3

Introduction ................................................................................................................................3

Important Operational Notes......................................................................................................3

Lamp Mounting ..........................................................................................................................7

Optimising the output.................................................................................................................7

Lamps ........................................................................................................................................8

Safe Practice..............................................................................................................................8

Maintenance...............................................................................................................................8

Safety.........................................................................................................................................8

Limited Warranty........................................................................................................................9

Pacific 80V Manual 3

Safety Warnings

1.0m

= 90

Not for residential use.

CAUTION: Hot Surfaces, Avoid contact by persons or materials.

The Pacific has some hot surfaces. Be careful to avoid burns. Take care with the Lamp

house and Heat sink. We suggest the use of leather gloves when focusing these

luminaires.

SAFETY - Mains Power Isolation

The Pacific range is fitted with a micro-switch that automatically disconnects the mains

power when the lamp holder is removed. However, it is also recommended that the

luminaire should always be electrically isolated from mains power before re-lamping,

cleaning or servicing.

CAUTION: Risk of fire - Use with max 1200 watt 80V lamp

CAUTION: These luminaires are not suitable for mounting on a normally flammable

surface

These luminaires are not suitable for outdoor use. They are rated at IP00

The luminaire should be at least 1.0 metres away from the nearest object it is lighting.

The Pacific range can be operated only through a range of angles 90°either side of

horizontal.

Introduction

The 80V power system is an innovation designed for use in our Pacific range of luminaires. It exploits the

advantages of a lower voltage supply to increase efficiency with the additional benefit of a higher colour

temperature, which increases the perceived brightness.

The power supply developed for Selecon is an electronic transformer tracking the incoming (dimmed)

supply to deliver a maximum of 80V at the lamp. Mains supply input 220 – 240V to be supplied via a high

quality entertainment type dimmer. The transformer output tracks the dimmer output, typically the

response delay is as found with 2000w mains voltage luminaires.

The 1200W 80V lamp is a high performance lamp intended for ‘non continuous’ use i.e. as for a studio

lamp / theatre lamp, a few hours of use at a time, regularly. It is not intended as a display type luminaire.

Important Operational Notes

CHECK MAINS VOLTAGE OUTPUT AT YOUR DIMMER before setting up the 80V

power supply for your installation.

The Pacific 80V system exploits the advantages of LOW VOLTAGE lamp filament technology; it is

essential that the voltage input switch is correctly set for the maximum voltage measured at the dimmer

output. Voltage losses affect all installations, it is not sufficient to rely on the ‘quoted’ voltage for the local

territory.

Failure to check the mains voltage at the dimmer and correctly set the voltage switch 220 / 230 / 240 may

result in less than optimal output from your Pacific 80V system.

Pacific 80V Manual 4

MOUNTING THE POWER SYSTEM ON THE PACIFIC YOKE

First remove the lens tube, then follow the steps below.

Hook Clamp Mounting

The 80V power supply has the option of a hook clamp mounting (order code 20HC).

We recommend mounting the power supply separate from the luminaire as detailed

below.

Situations where the hook clamp option MUST be used are as follows:

•Installations with an ambient air temperature above 25°C

and / or

•Installations where the luminaire will be run at full power for any extended length of

time as per this manual.

The hook clamp is installed through the top of the mounting bracket attached to the back

of the power supply heat sink. A M12 Bolt, M12 Nut and 2 x M12 washers are supplied

with the power supply

When the 80V power supply is used with the hook clamp mounting, a safety chain (order code 20SC)

must be used. This must be passed through the oval anchor holes located on the sides of the mounting

bracket.

Step 1 – Rotate yoke clockwise Step 2 – Attach power supply using mounting

bolts and washers supplied with unit.

Step 3 – Rotate yoke clockwise

Step 4 – Insert lamp module.

Pacific 80V Manual 5

Indicator LED

Voltage Switch

WARNING

The 80V 1200W lamp generates a considerable heat output. Supplied with each 80V Power System is a

high heat resistant lens tube clamp knob, and white teflon washer Replace the current lens tube clamp

knob and red fibre washer on the Pacific luminaire with this one.

SETUP

The Power System is an electronic transformer. The output is therefore in direct relationship to the

incoming mains power supply. It is essential that the lamp receives full 80V if the performance advantages

of the lamp are to be achieved.

The Power Supply has three

voltage settings - 220, 230 and

240v accessable from the front

cover. The switch can be slid from

the bottom (240V), to a middle

position (230V), up to the top

position (220V).

To set-up the power supply.

NB: Please refer to the notes on page 3 regarding mains voltage output.

Site Conditions –

The Pacific Power System is designed for high performance applications such as entertainment and

studio lighting. Angles of use of the luminaire are unrestricted i.e. - straight down is OK, however

prolonged operation in the horizontal position is not recommended. The power supply and yoke should

always be pointing vertical.

After extended use some surface discolouration may be observed on the internal plastic surfaces of the

Fortron gate material. This is non structural and can be likened to the degradation paint undergoes within

a lamp house.

Pacific 80V Manual 6

LAMP SET UP

Before inserting a lamp into the module, we suggest that you practice the motion of removing and

inserting the lamp holder module from the lamphouse.

Loosen the thumb-screw at the front of the lamp holder module by about 5mm. Holding the lamp holder

module, slide it forward until both the rear lip and the front 'T' of the lamp holder module clear their home

positions [1], then pull the lamp module down [2]. Reverse this action to replace the lamp holder and then

tighten the thumb-screw to lock the lamp holder module into position.

Lamp Replacement & adjustment:

Isolate electrically before re-lamping the luminaire. Also be aware that the lamp or luminaire may

still be hot, so exercise necessary caution to avoid burns.

To ensure optimum performance from your Pacific luminaire, follow the steps below:

Front ‘T’ Rear Lip

Pacific 80V Manual 7

Lamp Mounting

The lamp module is factory set at a mid peak / flat field. Mount the lamp ensuring that the pins are fully

pushed home. Fit the module into the luminaire and secure as above.

Turn on and make final peak / flat setting as desired – refer notes below on ‘Optimising the Output’

To replace the lamp –

1 Remove the lamp holder module as described above.

2 Set the level of the metal cup holding the lamp base.

Level the cup with the edge of the module by adjusting the three levelling screws.

3 Remove the old lamp. Align the pins of the new lamp to the correct holes and push the lamp

firmly home. Do not touch the quartz envelope of the lamp with your fingers - use the plastic

sheath supplied to insert the lamp.

4 Carefully replace the lamp holder module and tighten the thumbscrew to lock it into position.

Reconnect the luminaire to the power supply.

5 Turn on the luminaire to approximately 30%. This makes the peak easier to see. Set the beam

angle to its widest with a sharp edge

6 Centre the lamp in the middle of the beam if necessary, by adjusting the three levelling screws.

Optimising the output

The lamp position can be altered to 'peak' or

'Flat' light output. The peak beam gives a central

hot spot falling off evenly to the beam edges.

This setting is useful for normal stage lighting

purposes where beams are overlapped to

achieve an even cover. Flat adjustment

provides a visually even light beam suitable for

gobo projection. Take care to move the lamp

carefully as the lamp filament is burning white

hot and at its most vulnerable. Don't over-tighten

the knobs, finger tight pressure is all that is

required. Peak-Flat gear

Lamp tilt gear

1 Adjust the beam to its narrow angle, with a sharp edge.

2 Peak the output (turn the centre gear clockwise) until you see light flare around the edge of the

beam.

3 Turn the centre gear anti-clockwise until the flare is removed and you have a clean sharp-edged

beam. This is the position of maximum light output.

4 A useful technique to check how well the lamp is centred is to push two of the shutters into the

beam, and then check if any reflection off the shutters is visible in the beam. If so, adjust the

screw on the side opposite to the reflection until it disappears.

5 To set a ‘FLAT’ beam, turn the centre gear anti-clockwise until the distribution appears even

across the beam.

Lamp

Lamp Holder Module

Neutral Peak

Flat

15mm

Pacific 80V Manual 8

Note that, as in all lamps, the unit should be run for 15-20 minutes before optimum light output is

achieved.

Powercon Connector

The 80V lamp module comes supplied with a Powercon connector. This connector is plugged into the

Powercon socket that is fitted on the 80V power supply.

The Cable Conductor colour codes are as follows:

Brown - Phase, Live

Blue - Neutral

Green/Yellow - Earth

Lamps

The Pacific 80V 1200W Power System is designed for use with either –

Philips - 6980Z

GE - OC1200

Important Note: The quoted performance figures are achieved with Philips lamps. Other manufacturers

lamps can be used, but no assumptions should be made as to relative performance.

Please refer to the instructions of the lamp manufacturer when disposing of failed lamps.

Safe Practice

Heat

The Pacific incorporates an innovative design to effectively remove the heat out of the luminaire, away

from the critical heat-sensitive components such as the lamp base and wiring. The components that form

part of the heat removal system, the heat-sink and lamp house, will operate at temperatures which can

burn you!!! Take care in handling the luminaire. We recommend the use of gloves when focusing.

Mains Isolation

The Pacific range is fitted with a micro-switch that automatically disconnects the mains power when the

lamp module is removed. However, it is also recommended that the luminaire should always be

electrically isolated from mains power before re-lamping, cleaning or servicing.

Maintenance

The electronics of the Pacific Power System is fitted with an 8A slow blow (6.35 x 32mm) fuse. It is

possible that this fuse may blow in the event of a lamp failure involving the collapse of the filament

structure.

Replacing the lamp and fuse are the only maintenance tasks that can be safely carried out by non-

approved personnel. Refer below - Safety & Maintenance note.

Safety

Selecon have manufactured this luminaire in accordance with recognised best practices to recommended

international safety standards. It is your responsibility to maintain this luminaire in good & safe working

condition.

Repairs should only be carried out by suitably qualified persons. Do not operate the luminaire with

cracked lens, damaged cable, etc. Consult your Selecon distributor for assistance. Only replace

damaged parts with authorised Selecon spares.

N.B. Luminaire Cable - Your Selecon luminaire is fitted with special heat resistant flexible cable, replace

with genuine Selecon spare part cable kit only - refer to your Selecon distributor. (Replacement cables

are supplied complete with necessary terminal connectors.)

Pacific 80V Manual 9

Cable Conductor colour codes:

Brown - Phase, Live

Blue - Neutral

Green/Yellow - Earth

Limited Warranty

Selecon New Zealand Ltd. (“Selecon”) warrants its luminaires against defects in

materials or workmanship. The term of this warranty is based on the product

usage and is from the date of delivery.

Usage – Entertainment, Theatre Term - Three Years

Entertainment, Theatre relates to the typical conditions found in a theatre performance venue

viz:

4 – 6 hrs per day, six days per week.

Usage – Architectural, DisplayTerm - One Year

Architectural, Display relates to typical usage such as display lighting in a Museum viz:

10 – 12 hrs per day, seven days per week.

Other – ALL Electromechanical / Electronic DevicesTerm - One Year

This warranty is void in any of the following circumstances: (a) The luminaire has been misused,

neglected, damaged or abused. (b) The luminaire has been improperly installed, operated, repaired or

maintained. (c) The luminaire has been modified. (d) The luminaire has been connected to other

equipment with which it is not compatible. (e) The luminaire has been used or stored in conditions outside

its electrical or environmental specifications. (f) The luminaire has been used for purposes other than for

which it was designed. (g) The luminaire has been used outside its stated specifications and operating

parameters.

Correct installation of the luminaire is the owner’s responsibility.

To assert a warranty claim, complete Selecon’s return authorisation form (available from Selecon). Return

the luminaire to Selecon or its authorised agent.

If Selecon accepts the warranty claim, Selecon will provide, or arrange for, service, repair or replacement

as Selecon shall determine in its sole discretion. Selecon shall bear the cost of such service, repair or

replacement. However, the owner shall bear the cost of freight and insurance on the luminaire, both

ways. If Selecon does not wish to service, repair or replace the defective luminaire, it shall refund the

purchase price.

Selecon’s sole responsibility is to repair, replace or service a luminaire subject to a valid warranty claim.

Under no circumstance will Selecon be liable for direct, indirect, incidental, special or consequential costs

or damages, including dismantling and re-installation costs, loss of operations or profits, to the maximum

extent permitted by law.

Selecon accepts no liability for personal injury or property damage resulting from failure to heed relevant

operating and safety procedures specified by Selecon or imposed by law.

This is an express warranty. Selecon disclaims any other express or implied warranties, including

warranties of merchantability or fitness for purpose, to the maximum extent permitted by law.

Some jurisdictions do not allow limitations or disclaimers of implied or statutory warranties. Some

jurisdictions do not allow disclaimers or exclusions of consequential or incidental damages. Therefore, the

above disclaimers, limitations and exclusions may not apply in all jurisdictions in which Selecon sells its

luminaires.

This warranty gives the owner specific legal rights. The owner may have other rights or remedies

pursuant to the laws in its territory. Nothing in this limited warranty should be construed as limiting or

restricting any other statutory right or remedy of the owner, except for such limitations or restrictions

herein as may be allowed by the law of the territory.

Pacific 80V Manual 10

Selecon has a policy of continual product improvement and specifications are subject to change without

notice.

Contacting Selecon

Selecon New Zealand Ltd.

19-21 Kawana Street, Northcote

Auckland, New Zealand

Tel: 64-9-481 0100, Fax: 64-9-481 0101

e-mail: selecon@seleconlight.com

website: www.seleconlight.com

Please contact Selecon, or check our web site to find the Selecon distributor nearest to you.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Selecon Matériel de DJ

Selecon

Selecon PLFRESNEL 1 MKII Manuel utilisateur

Selecon

Selecon RAMA 175 HP 80V FRESNEL Manuel utilisateur

Selecon

Selecon ACCLAIM AXIAL ZOOMSPOT Manuel utilisateur

Selecon

Selecon Scene Setter Manuel utilisateur

Manuels Matériel de DJ populaires d'autres marques

ALPHA LITE

ALPHA LITE ALPHA 1500 Manuel du propriétaire

Chauvet

Chauvet OVATION E-930VW Manuel utilisateur

Zumtobel

Zumtobel APHRODITE Home Manuel utilisateur

Snow Masters

Snow Masters Zig Oscillator Manuel utilisateur

EuroLite

EuroLite 50530554 Manuel utilisateur

Beamz

Beamz BUV243 Manuel utilisateur

thomann

thomann Stairville DJ Lase 40-G MK-III Manuel utilisateur

Eagletone

Eagletone 6 Eyes Flower Manuel utilisateur

EuroLite

EuroLite FLD-1508 Manuel utilisateur

Technical Pro

Technical Pro LG8xSEA Manuel utilisateur

JB Systems

JB Systems Lounge Laser DMX Manuel utilisateur

Lightmaxx

Lightmaxx Vega Halo 90 Manuel utilisateur

Elation

Elation FUZE WASH Z350 Manuel utilisateur

Maverick

Maverick MK3 WASH Manuel utilisateur

Infinity

Infinity TF-260C7 Fresnel Manuel utilisateur

Chauvet

Chauvet EVE E-50Z Manuel utilisateur

Eliminator Lighting

Eliminator Lighting E 138 Manuel utilisateur

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manuel utilisateur