Sekonic SR-6500 Manuel utilisateur

DIC

579 K

10 30 50 70 90

CL0797100

Operating manual

Operating Manual

7-24-14,OizumiGakuen-cho,Nerima-ku,Tokyo178-8686,Japan

Telephone:+81-3-3978-2375Facsimile:+81-3-3978-5229

-1-

Introduction

Thank you very much for purchasing our product.

Please read the operating manual before using this product, and be sure to use it properly.

After reading this operating manual, be sure to keep it in a place that you can access at any time.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Introduction

-2-

Table of contents

Safety precautions ............................................................................................. 5

Before using ......................................................................................................... 8

Power cord list for Europe ................................................................................... 9

Warranty ................................................................................................................. 10

Precautions for use ........................................................................................... 11

Names of parts .................................................................................................... 14

Operating panel functions and operating instructions ............................... 15

Operation

Preparation ...................................................................................................... 16

Turning power on ............................................................................................ 17

Connecting to a computer ............................................................................. 18

1. USB

1-1. Operating mode.................................................................................... 19

1-2. Interface settings .................................................................................. 20

2.RS-232C

2-1. Operating mode.................................................................................... 21

2-2. Interface settings

2-2-1. Setting baud rate ....................................................................... 22

2-2-2. Setting character bit length........................................................ 22

2-2-3. Setting parity.............................................................................. 23

2-2-4. Setting stop bit........................................................................... 23

2-2-5. Setting ow control.................................................................... 24

2-2-6. Setting character code .............................................................. 25

Loading paper ................................................................................................. 26

Setting paper weight ...................................................................................... 29

Stacker unit (printer) preparation .................................................................. 30

Printer unit precautions for use .................................................................... 34

Marking instructions ......................................................................................... 35

Data reading settings

Setting column ................................................................................................ 36

Setting reading method .................................................................................. 37

Setting min. density level ............................................................................... 39

Setting density balance .................................................................................. 40

Setting reading side ........................................................................................ 41

Setting paper weight ...................................................................................... 42

Paper size setting ........................................................................................... 43

Error detection settings ................................................................................... 44

Buzzer settings

Buzzer control ................................................................................................. 46

Buzzer sound adjustment .............................................................................. 47

Table of contents

-3-

Stacker settings .................................................................................................. 48

Printer settings

Printer control ................................................................................................. 49

SR-6500 mode

1. Character size setting ................................................................................... 50

2. Character interval setting.............................................................................. 51

SR-9000 mode

1. Character size setting ................................................................................... 53

2. Character magnication setting.................................................................... 54

3. Character interval setting.............................................................................. 55

Barcode settings

Barcode control .............................................................................................. 57

Low power consumption settings

Sleep duration.................................................................................................. 58

Stanby duration................................................................................................ 59

Displaying various information

Displaying the version .................................................................................... 60

Displaying front side reading sensor settings ............................................. 61

Displaying back side reading sensor settings ............................................. 62

Displaying optional unit settings ................................................................... 63

Displaying total count ..................................................................................... 64

Displaying serial number ................................................................................ 65

Operating tests

Feed test 1 ....................................................................................................... 66

Feed test 2 ....................................................................................................... 67

Printer inkjet test ............................................................................................ 68

Printer jet test ................................................................................................. 69

Clearing paper jams ....................................................................................... 70

Options

Back side reading unit ..................................................................................... 71

Barcode unit / V • Barcode unit / H

Barcode readable area ................................................................................... 72

1. Barcode unit / V (vertical feeding) ................................................................ 72

2. Barcode unit / H (horizontal feeding) ............................................................ 75

Barcode reading position adjustment .......................................................... 77

Barcode unit precautions for use .................................................................. 79

Cleaning ................................................................................................................. 80

Cleaning procedures ...................................................................................... 80

Cleaning point ................................................................................................. 81

Service schedule ................................................................................................ 85

Product specications ..................................................................................... 87

Printer unit specications .............................................................................. 89

Barcode unit specications ........................................................................... 90

Table of contents

-4-

External diagram ................................................................................................ 92

List of menu modes ........................................................................................... 93

Error displays and countermeasures

1. Errors............................................................................................................. 96

2. Warnings ..................................................................................................... 100

OMR glossary .................................................................................................... 103

Appendix

Sheet creation reference............................................................................... 109

Table of contents

-5-

Safety Precautions

These “Safety Precautions” pages list various symbols for ensuring safe operation of this

product so as to prevent users or other people from being injured, or property from being

damaged.

Read these precautions thoroughly and understand the meanings of the symbols before

proceeding to the main text of this manual.

Safety Precautions

Warning

Improper operation by neglecting these instructions may result in death or serious

injury.

Caution

Improper operation by neglecting these instructions may result in personal injury or

property damage.

Neglecting these instructions may generate smoke or re.

Neglecting these instructions may cause electric shock.

Indicates a prohibited action.

Indicates that disassembly or modication is prohibited.

Indicates that the power plug must be removed from the outlet for safe

operation.

Instructs that do not spray the materials containing an inflammble gas or

liquid to the device.

-6-

Warning

Fire or electric shock may result if this product continues to be used

when there is a strange smell or sound.

In such a case, immediately turn the power switch off and then remove

the power plug from the outlet. After making sure that it is no longer

smoking, ask the sales shop for repair service.

Never attempt to repair by yourself since that may be very dangerous.

Do not modify or disassemble this device. That could cause fire or

electric shock.

Do not remove the cover from this device. That could cause electric

shock. Ask the sales shop to conduct any internal checking,

adjustment or repair.

Pay thorough attention to the above instructions. Otherwise, fire or

electric shock may occur.

Power plug precautions

•Do not pull on the cord when removing the power plug from the outlet.

• Do not use any power plug other than the specied one.

Make sure to use the adapter included in the package.

Device precautions

• Do not use it with a supply voltage other than the specied one.

•Do not install it in a place that may be wet with water or oil, steam,

moisture or dust.

•Do not insert or drop any metal, foreign combustible matter, etc., into

the port.

•Do not place containers with chemicals or water, or small metal pieces

near the device.

Do not cover the vent hole. That could cause heat retention, resulting

in re.

If the device is dropped or the cover is broken, immediately turn the

power switch off and remove the power plug from the outlet. Then,

contact the sales shop.

If any foreign matter should enter inside, immediately turn the power

switch off and remove the power plug from the outlet. Then, contact

the sales shop or Sekonic. If the device continues to be used with

foreign matter inside, re or electric shock may occur.

If water or other substances penetrate the unit, immediately turn the

power switch off and remove the power plug from the outlet. Then,

contact the sales shop or Sekonic. If the device continues to be used with

water or other foreign matter inside, re or electric shock may occur.

 Do not spray any materials containing an inammable gas or liquid on

the device and be sure to keep this kind of materials away from this

device.

Use a cleaning cloth with suitable amount of cleaning liquid to wipe

off well, after removing the power plug from the outlet and the device

becomes to cool off.

-7-

Caution

Do not put heavy things on the device. Otherwise, it may fall or

collapse, resulting in injury.

Do not place the device in an unstable location. Otherwise, it may

fall or collapse, resulting in injury.

When opening or closing the upper part of the main body, do not

place your hand on the paper-feeding surface. Otherwise, fingers

may be caught, resulting in injury.

If you must touch the paper-feeding surface of the main body, be

careful not to allow your ngers to be caught or hit.

When doing maintenance on the device, for your own safety, be sure

to remove the power plug from the outlet.

When the device is not in use for long periods, for safety, remove the

power plug from the outlet.

Before moving the device, be sure to remove the power plug from

the outlet. If the cable is damaged, re or electric shock may occur.

Do not connect or disconnect the power plug if your hands are wet.

Otherwise, an electric shock may occur.

Caution

-8-

Before using

Before using the device, check if all of the following items are included in the package. If

components are missing or damaged, contact the store where you purchased the device.

5. Power cord

For U.S.A

6. Operating manual

(this booklet)

9. USB cable

1. Main body unit 2. Main tray 3. Selection tray 4. Paper feeding

bracket

For Europe

Note)

Refer to the power cord list

for Europe of next page.

8. CD-ROM

10. Ink cartridge

Mark entry sheet:

use it as an example when

designing entry sheets.

7. A4 check sheets

A4 mark entry sheets

Check sheet:

use it for checking OMR operations.

11. Strage bag

(Transparent plastic bag)

Operating manual

Note)

The package doesn’t include a RS-232C(9 pins) interface

cable. You may need to get one depending on your computer

port or connection method.

Before using

-9-

Power cord list for Europe

As stated on page 7 of this manual, the machine includes a representative variety of power

adapters. If none of the included adapters match the power outlets in your location, please

nd and use an appropriate adapter.

Before using Power cord list for Europe

Country Plug type

U.K. B, B3, BF, C

Italy A, C, SE

Austria B3, BF, C, O, SE

Netherlands B, C, SE

Greece B, B3, C, SE

Sweden B, C, SE

Spain A, C, SE

Denmark C

Germany A, C, SE

Finland A, B, C, SE

France A, C, O, SE

Belgium A, B, C, SE

Portugal B, B3, BF, C, SE

Luxemburg A, C, SE

Ireland A, B, B3, BF, C, SE

A type

(American Type)

BF type

(British Type)

C type

(CEE Type)

B type

(British Type)

B3 type

(British Type)

SE type

(CEE Type)

O type

(Ocean Type)

Table des matières

Autres manuels Sekonic Lecteur de codes-barres

Sekonic

Sekonic SR-430 Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques

POSMicro

POSMicro Datalogic PowerScan D7100 Manuel utilisateur

Marson

Marson MT780 Guide de configuration rapide

NCR

NCR RealPOS Manuel utilisateur

Motorola

Motorola SE3300 Guide de configuration rapide

Element

Element P130BT Manuel utilisateur

Motorola

Motorola Symbol LS3008 Manuel d'installation et d'exploitation

Meec tools

Meec tools OBD-II / VAG Manuel utilisateur

SICK

SICK CLP 100 Manuel utilisateur

Royal Tag SA

Royal Tag SA I-Read Manuel utilisateur

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuel utilisateur

Meteor

Meteor 8310 Manuel utilisateur

Denso

Denso BHT-500B Manuel utilisateur

Datalogic

Datalogic Heron HD3130 Manuel utilisateur

Motorola

Motorola MP6000 Instructions de montage

Newland

Newland NLS-HR15-BT Manuel utilisateur

ARTDEV

ARTDEV AS-1310 Manuel utilisateur

Aopos

Aopos AS290 Manuel utilisateur

ENS

ENS 367-5455 Manuel utilisateur