Seko Pool Basic Pro Evo Manuel utilisateur

0000137188 Rev. 1.0

User Manual

0000137188 Rev. 1.0

CONTENTS

1. GENERAL INTRODUCTION ...............................................................................................................................3

2. INSTALLATION PRECAUTIONS........................................................................................................................3

3. IDENTIFICATION OF COMPONENTS................................................................................................................4

4. TECHNICAL SPECIFICATIONS..........................................................................................................................5

5. ASSEMBLY INSTRUCTIONS..............................................................................................................................6

5.1 APPLICATION EXAMPLE .................................................................................................................................7

6. DESCRIPTION OF THE CIRCUIT .......................................................................................................................8

7. CALIBRATION MENU .........................................................................................................................................8

7.1 CALIBRATION........................................................................................................................................................8

8. PROGRAMMING............................................................................................................................................... 10

9. DOSING METHOD............................................................................................................................................ 13

9.1 PHPROPORTIONAL DOSING ........................................................................................................................... 13

9.2 ON/OFF PHDOSING..................................................................................................................................... 13

9.3 ALARM FOR THE PHSET POINT ..................................................................................................................... 14

10. ACTIVATIONS ................................................................................................................................................ 15

11. ALARMS ......................................................................................................................................................... 15

12. PRE-DEFINED CONTROL PARAMETERS................................................................................................... 15

13. LIST OF POSSIBLE ANOMALIES AND RELATIVE SOLUTIONS............................................................... 16

14. HANDLING...................................................................................................................................................... 17

15. STORING THE PUMP AFTER USE............................................................................................................... 18

WARNINGS........................................................................................................................................................... 18

0000137188 Rev. 1.0

1. GENERAL INTRODUCTION

The Pool Basic Pro EVO control method belongs to a new line of instruments carefully

developed by the supplier for the innovative management of pools. This device is easy

to use and permits continuous control of the pH.

The peristaltic pumps have a 1,5 l/h flow rate for pH regulation and have a pressurised

injection flow rate up to 1.5 bar.

This easy-to-use instrument does not require special maintenance operations. It is

equipped with a self-regulation procedure and automatic control of the electrode’s state.

2. INSTALLATION PRECAUTIONS

WARNING!!!

Disconnect power before carrying out ANY operation inside the

control panel of the Pool Basic Pro EVO device.

NON-OBSERVANCE OF THE INSTRUCTIONS CONTAINED IN THE PRESENT

MANUAL COULD CAUSE INJURY TO PEOPLE AND/OR DAMAGE TO THE DEVICE.

WARNING

During installation of the Pool Basic Pro EVO device, proceed as follows:

Make sure that the supply voltage coincides with the one indicated on the label on

the side of the device.

Make sure that the injection pressure is below 1.5 bar.

Make sure that the pump’s protective cover is properly latched.

Make sure that the suction hose is immersed with the relative foot (PVC hose) in the

tank of the product which must be injected and that it is connected to the pump

(symbol on cover ▲). After carrying out the checks stated above, tighten the

connector nut.

Connect one end of the delivery hose (▼ symbol on cover) to the pump and connect

the other end to the pool through the injection valve.

NOTE: To insert the product which must be injected into the pump when starting for the

first time and every time the tank is changed, set the switch to forced running

using the button.

0000137188 Rev. 1.0

3. IDENTIFICATION OF COMPONENTS

PH 7 PH 4 H0

BCD

Instructions manual

KEY

A. Pool Basic Pro EVO regulator

B. Suction hose in PVC Crystal 4x6 (4 m) x 2

C. Delivery hose in PE 4X6 (5 m) x 2

D. pH Electrode model SPH-1

E. Reducer for injection valve x 2

F. Duckbill valve in FPM (3/8” GAS) x 2

G. Suction foot (PVC hose) x 2

H. Tapping double-bolt clamp for fastening PSS3 probe holder onto 2” =50mm

hose

I. Tapping double-bolt clamp for fastening injection valve onto 2” =50mm hose x 2

J. Probe holder model PSS3 (1/2” GAS)

K. Hose 3x7

L. Fixing bracket kit

M. pH 4, pH 7, H2O Buffer solution kit

N. Instruction Manual

0000137188 Rev. 1.0

O. Temperature sensor

4. TECHNICAL SPECIFICATIONS

Power supply: 100÷240 Vac 50/60 Hz 30 watt

Switch: on side of box

Inlet measurements: pH, through BNC

opH scale: 0÷14.0 pH

opH precision: +/-0.1 pH

Temperature Scale: 0÷100 °C (PT100 sensor)

Pump flow rate with transaxle technology:

opH:1.5 l/h (hose 6X10) 1.5 bar

oH2O2:0.4 l/h (hose 3X7), 1.5 l/h (hose 6X10) 1.5 bar

Pump relay pH: 10 A 250 V (dry contact)

Relay for alarm: 10 A 250 V (dry contact)

Relay for H2O2:10 A 250 V (dry contact)

Dedicated power for pumps: 240 Vac 10 watt

Input signal: 100÷240 Vac

Level probe: pH, H2O2

Install the Pool Basic Pro EVO control device on a hard support (vertical wall) where it

can be easily accessed by the operator. Attach the Pool Basic Pro EVO control device

using the provided fixing bracket (distance between centre of holes: 95mm. Hole Ø 6).

Before carrying out any operation inside the equipment, make sure that the switches are

on 0. Unscrew the two screws on the upper part of the equipment by a quarter of a turn

and the front side will fold down on the hinges.

0000137188 Rev. 1.0

5. ASSEMBLY INSTRUCTIONS

* NOTA 2: LA PRESSIONE MAX. NON DEVE ESSERE SUPERIORE A 1,5 BAR.

PER AUMENTARE LA DURATA DEL TUBO, LA PRESSIONE NON DEVE SUPERARE 1 BAR.

* NOTA 1: IL CAVO DEVE PASSARE IN UNA ZONA DIVERSA DA QUELLA DI ALIMENTAZIONE

PER POMPE GROSSE, PER EVITARE DISTURBI DI CORRENTE.

0 7

Lunghezza massima de cavo: 6 mt

Pressione Massima: 1,5 bar

* NOTA 2

* NOTA 1

*NOTE 1: FOR LARGE PUMPS, THE CABLE MUST PASS THROUGH AN AREA OTHER THAN THE POWER

SUPPLY ZONE IN ORDER TO PREVENT CURRENT DISTURBANCES.

*NOTE 2: THE MAX. PRESSURE MUST NOT EXCEED 1.5 BAR.

TO INCREASE THE HOSE’S LIFETIME, THE PRESSURE MUST NOT EXCEED 1 BAR.

Max. length of cable: 6m

*NOTE 1

Maximum pressure

*NOTE 1

0000137188 Rev. 1.0

5.1 APPLICATION EXAMPLE

Note:

The linear distance of the hose between the probe and the point of injection must

not be less than 60cm.

COMPENSATION

TANK

RECIRCULATION

PUMP

FILTER

HEAT

INTERCHANGER

0000137188 Rev. 1.0

6. DESCRIPTION OF THE CIRCUIT

1) Inlet pH measurement

2) Inlet temperature probe

3) Inlet probe level for product pH

4) Inlet probe level for product H2O2

5) Keyboard input

6) Flow (recirculation pump)

7) Relay for pH product, external pump.

8) Alarm relay

9) Relay for H2O2product, external pump.

10)Power supply input

11)Switch

12)Fuse

13)Power supply for pH pump

14)Power supply for H2O2pump

7. CALIBRATION MENU

7.1 Calibration

Before proceeding, the calibration must be enabled. Scroll down the menu

AdvancedCal, the display will show:

Exit the menu and return to the normal system status.

Calibration Menu Display

Settings

Advanced

Cal Off

Press ENTER to access the menu.

Advanced

Cal Full

Press ENTER and the + and –keys to

modify the calibration. Select Full and

confirm with ENTER.

Al arm

RL pH

Input

Flow

Net

Fuse

µChip

Rel ay Rel ay Relay

156789

Lev

Temp

Probe

Input

234

PumppH

- +

Lev

RLHO

H O Pump

2 2

Not Used

Not

Used

Not

Used

0000137188 Rev. 1.0

7.1.1 Calibrating the pH probe

Get some water

Remove the probe from the probe

holder

Wash the probe

Keep the probe in the buffer solution

pH 7

Press and hold down the Cal button

for 3 seconds

Tm 25°C 14pH

Press Cal to start calibration with a

buffer solution pH 7

Press CAL

B.Solution 7pH

The calibration takes 1 minute

Wait 59s

B.Solution 7pH

Probe quality

Quality

B.Solution 7pH

HO2

Wash the probe

4 pH

Keep the probe in the buffer solution

pH 4

Press Cal to start calibration with a

buffer solution pH 4

Press CAL

B.Solution 4pH

The calibration takes 1 minute

Wiat 59s

B.Solution 4pH

Probe quality

Quality

B.Solution 4pH

HO2

Wash the probe

Put the probe back in the probe holder

and press Cal to finish

0000137188 Rev. 1.0

8. PROGRAMMING

The programming menu can be accessed by simultaneously pressing the Cal and Set

keys for at least 3 seconds.

Upon release of the keys the display will show:

To prime the pH pump, press the UP button for at least 3 seconds and release it to stop

the operation. To prime the H2O2pump repeat the same procedure pressing the DOWN

button for at least 3 seconds.

Progrma Menu

pH Measure

Use Enter to access the sub-menus:

Setpoint

Dos type

OFA time

Alr Band

Type

pH Measure

Setpoint 7.4 pH

Press Enter and the + and - keys to change

the Set Point value (0÷14 pH)

pH Measure

Sp Type Acid

Press Enter and the + and - keys to change

the Set Point type.

Acid

Alkaline

pH Measure

OFA Time Off

Press Enter and the + and - keys to set the

OFA time to OFF or from 1 to 240 min. (see

Paragraph 9.5)

pH Measure

Alr Band 3.0pH

Press Enter and the + and - keys to set the

band alarm from 1 to 3 pH.

pH Measure

Type PROP

Press Enter and the + and - keys to change

the dosing type.

PROP (see Paragraph 9.1).

ON/OFF (see Paragraph 9.2).

OFF (dosing disabled)

Language Display

Settings

Progrma Menu

Language EN

Press Enter and the + and –keys to change

the language:

FR, EN, IT, ES, DE

pH measurement display

Settings

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Seko Contrôleurs

Seko

Seko Kontrol 800 Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur