SEH myUTN-50 Manuel utilisateur
Quick Installation Guide 1
Monday - Thursday
Friday
8:00 a.m. to 4:45 p.m. and
8:00 a.m. to 3:15 p.m. (CET)
℡+49 (0)521 94226-44
USB Device Server
myUTN-50
Quick Installation Guide
Overview [en]
This Quick Installation Guide provides
a description of the installation of the
myUTN-50. It contains the following
information:
General Information
Safety Regulations
Hardware Installation
Software Installation
Getting Started
Configuring the UTN Server
Please note the table of contents on
page 3. Should you have any further
questions, please contact our support
hotline.
Überblick [de]
Dieser Quick Installation Guide beinhaltet
eine Beschreibung der Installation des
myUTN-50. Sie erhalten die folgenden
Informationen.
Allgemeine Information
Sicherheitsvorschriften
Hardware Installation
Software Installation
Erste Schritte
UTN Server konfigurieren
Beachten Sie das Inhaltsverzeichnis auf
Seite 17. Falls Sie noch Fragen haben,
kontaktieren Sie unsere Support
Hotline.
2 Quick Installation Guide
Date of Manufacture
The serial number includes the date of manufacture.
The serial number can be found on the type plate.
Quick Installation Guide [en] 3
2 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2 Safety Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2 Hardware Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2 Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2 Getting Started: SEH UTN Manager . . . . . . . . . . . . . . . . 9
Starting the SEH UTN Manager . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Assigning an IP Address to the UTN Server . . . . . . . . . . . . . . 11
Adding the UTN Server to the Selection List . . . . . . . . . . . . . 12
Connecting the USB Device to the Client . . . . . . . . . . . . . . . . 13
2 Configuring the UTN Server . . . . . . . . . . . . . . . . . . . . . . 14
Configuring the UTN Server via the myUTN Control Center14
Configuring the UTN Server via the InterCon-NetTool. . . . 15
Contents
4 [en] Quick Installation Guide
General Information
Purpose
The myUTN-50 allows you to access non-network-ready USB devices (e.g. hard
disks etc.) in the network. The USB devices will be connected to the USB port of
the myUTN-50. The software tool ’SEH UTN Manager’ regulates the access of the
USB devices.
The SEH UTN Manager is installed on all clients that are meant to access a USB
device in the network. The SEH UTN Manager shows the availability of all USB
devices that exist in the network and establishes a connection between the client
and the USB device.
Delivery
Please check the package content before getting started:
UTN Server USB Device Server (myUTN-50)
Quick
Installation
Guide
The Quick Installation Guide provides a brief
description of the installation of the myUTN-50.
(This document)
myUTN
Product CD The myUTN Product CD provides:
- User Manual (The pdf file provides a detailed
description of the myUTN administration.)
- SEH UTN Manager,
- InterCon-NetTool (Administration tool),
- SEH Private-MIB,
- Adobe Reader
Power Pack external power pack
Quick Installation Guide [en] 5
Technical Data
*The shield connection of the RJ45 connector is connected to the shield of the device port. This
connection must be taken into account when arranging your network cabling. For more
information, please consult your retailer.
Properties Values
Device Connection - 2 x USB 2.0 HS (may be extended to 5 ports)
Network Connection logical:
physical: - IEEE 802.3
- RJ-45 (STP Cat.5)
Operating environment - Ambient temperature: 5 - 40 °C
- Relative humidity 20 - 80 %
Dimensions - Length 98 mm
- Width 81 mm
- Height 31 mm
- Weight 100 g
1) Link LED (green):
The link LED shows an existing connection to
the network.
2) Activity LED (yellow):
The LED indicates the reception of data
packets from the network.
3) Status LED (green):
The LED indicates that the device is
operational.
4) Reset button
5) Connector for the included power pack.
6) Network connector (RJ-45) for 100BaseTX and
10BaseT *
7) USB port 2 (may be extended using a USB hub)
8) USB port 1
9) Kensington security slot
6 [en] Quick Installation Guide
Safety Regulations
UTN servers are network devices for use in office environments. They are
designed for the integration of USB devices into networks.
Before starting the initial setup procedure and during the operation of the UTN
server, please note the following safety regulations. Their purpose is to protect
yourself and others from personal injuries, and avoid damage to the equipment.
Read the documentation and make sure that your system meets the
requirements listed therein.
Avoid contact with humidity or liquids.
The device must only be connected and operated if it is in perfect condition.
Make sure that no-one steps on or stumbles over the cables.
Do not connect a telephone cable to the RJ-45 connector. The RJ-45
connector may only be connected to SELV voltages. For the connection to the
RJ-45 connector only STP cabling (category 5 or better) may be used. The
shielding must fit flushly to the connector.
The device must only be operated using the power pack included in the
package.
Only use a certified USB Hi-Speed cable for the connection to the UTN server.
You will find a list of certified cables at www.usb.org.
Quick Installation Guide [en] 7
Hardware Installation
You can directly connect two USB devices to the UTN server (myUTN-50). If you use a
USB hub at the USB port 2, you can connect up to five USB devices.
No device with power supply solely via the USB port should be
connected to the UTN server.
Clients with software tool ’SEH UTN Manager’
Proceed as follows:
1. Connect the UTN server and the USB device to the USB data
cable. (Repeat this step if you want to connect more than one
USB device.)
2. Connect the network cable (RJ-45) to the UTN server.
3. Connect the power pack cable to the UTN server.
8 [en] Quick Installation Guide
Software Installation
The software tool ’SEH UTN Manager’ organizes the access of the USB devices.
The SEH UTN Manager is installed on all clients that are meant to access a USB
device in the network.
The SEH UTN Manager is available in two versions:
Single-User Version (SEH UTN Manager)
Multi-User Version (SEH UTN Manager + SEH UTN Service)
A major difference between the single-user version and the multi-user version is
the Windows service ’SEH UTN Service’. A detailed description can be found in the
myUTN User Manual.
Make sure the following points:
- The installation of the SEH UTN Manager is suitable for Windows XP and
later.
- The installation can only be carried out by Windows users with
administrative rights.
Proceed as follows:
1. Start the myUTN Product CD on your Windows client.
2. Select the SEH UTN Manager installation file from the Tools menu.
3. Follow the installation routine.
The SEH UTN Manager is installed on your client.
Quick Installation Guide [en] 9
Getting Started: SEH UTN Manager
After the SEH UTN Manager is started, the network will be scanned for connected
UTN servers. The network range to be scanned is freely definable.
After the network scan all UTN servers found – together with the connected
devices – will be shown in the 'network list'. The preferred devices will be selected
and added to the 'selection list'. The devices in the selection list can be connected
to the client.
This chapter describes the first steps with the program.
’Starting the SEH UTN Manager’ 10
’Assigning an IP Address to the UTN Server’ 11
’Adding the UTN Server to the Selection List’ 12
’Connecting the USB Device to the Client’ 13
Client and UTN server communicate via the UTN port 9200. This port must not be
blocked by a firewall. If necessary, you can change the port number and/or use a secure
UTN SSL port. A detailed description can be found in the myUTN User Manual.
Detailed information on how to use the SEH UTN Manager can be
found in the Online Help. To start the Online Help, select Help –
Online Help from the menu bar.
10 [en] Quick Installation Guide
Starting the SEH UTN Manager
Start the SEH UTN Manager on your client via the Windows start menu.
(Start --> Programs --> SEH Computertechnik GmbH --> SEH UTN Manager)
When you start the program for the first time, you will be informed that there
are no UTN servers available in the ’selection list’. Add the UTN server to the
selection list.
During the initial configuration, client and UTN server must be assigned to the
same local network segment.
Autres manuels pour myUTN-50
3
Table des matières
Langues :
Autres manuels SEH Serveur
SEH
SEH myUTN-50 Manuel utilisateur
SEH
SEH INU-100 Manuel utilisateur
SEH
SEH dongleserver Pro Manuel utilisateur
SEH
SEH EPS TSE Server 8 Manuel utilisateur
SEH
SEH myUTN Manuel utilisateur
SEH
SEH Dongleserver myUTN-800 Manuel utilisateur
SEH
SEH utnserver Pro Manuel utilisateur
SEH
SEH myUTN-50a Manuel utilisateur
SEH
SEH myUTN-52 Manuel utilisateur
SEH
SEH ProMAX Manuel utilisateur
SEH
SEH myUTN utnserver Pro Manuel utilisateur
SEH
SEH Mac OS 8 Manuel utilisateur
SEH
SEH Dongleserver myUTN-800 Manuel utilisateur
SEH
SEH myUTN-50a Manuel utilisateur
SEH
SEH INU-100 Manuel
SEH
SEH mySND-120 Manuel utilisateur
SEH
SEH myUTN-80 Manuel utilisateur
SEH
SEH myUTN-52 Manuel utilisateur
SEH
SEH myUTN-250 Manuel utilisateur
SEH
SEH myUTN-50a Manuel utilisateur
