SEESTATION SS-MES-CPE Manuel utilisateur

See Station

SS-MES-CPE

User Manual

Version. 1.2.2 (24.02.2006)

TABLE OF CONTENTS

PREFACE.........................................................................................................................................3

CH 1. MCPE-1924 INSTALLATION..............................................................................................4

PACKING LIST .................................................................................................................................4

HARDWARE INSTALLATION.............................................................................................................4

CH 2. FIRST TIME CONFIGURATION ........................................................................................6

BEFORE START TO CONFIGURE ........................................................................................................6

KNOWING THE NETWORK APPLICATION ...........................................................................................7

ADVANCED SETTINGS ...................................................................................................................30

CONFIGURING WIRELESS SECURITY .............................................................................................. 33

CONFIGURING AS WLAN CLIENT ADAPTER...................................................................................36

QUICK START TO CONFIGURE .........................................................................................................36

CONFIGURING UNIVERSAL REPEATER ............................................................................................39

CH 3. CONFIGURING WDS......................................................................................................... 41

WDS NETWORK TOPOLOGY ..........................................................................................................41

WDS APPLICATION.......................................................................................................................43

CH 4. ADVANCED CONFIGURATIONS .....................................................................................45

CONFIGURING LAN TO WAN FIREWALL .......................................................................................45

PORT FILTERING ...........................................................................................................................45

IP FILTERING ................................................................................................................................45

MAC FILTERING...........................................................................................................................46

CONFIGURING PORT FORWARDING (VIRTUAL SERVER) ...................................................................46

MULTIPLE SERVERS BEHIND NAT EXAMPLE: .................................................................................47

CONFIGURING DMZ .....................................................................................................................47

CONFIGURING WAN INTERFACE....................................................................................................48

STATIC IP .....................................................................................................................................49

DHCP CLIENT (DYNAMIC IP) .......................................................................................................50

PPPOE .........................................................................................................................................50

PPTP ...........................................................................................................................................51

CONFIGURING CLONE MAC ADDRESS...........................................................................................52

CONFIGURING DHCP SERVER .......................................................................................................54

BANDWIDTH CONTROL ................................................................................................................. 55

QOS (QUALITY OF SERVICE) .........................................................................................................57

STATIC ROUTE SETUP....................................................................................................................61

DYNAMIC ROUTE SETUP ...............................................................................................................62

VPN PASS-THROUGH ....................................................................................................................63

USING CLI MENU.........................................................................................................................63

THE SYSTEM MANAGEMENT .........................................................................................................66

SNMP AGENT ..............................................................................................................................67

FIRMWARE UPGRADE ....................................................................................................................69

CONFIGURATION DATA BACKUP & RESTORE ..................................................................................70

AUTO DISCOVERY TOOL ...............................................................................................................71

Preface

This guide is for the networking professional who installs and manages the Mesh City

MCPE-1924 outdoor product hereafter referred to as the “device”. To use this guide,

You should have experience working with the TCP/IP configuration and be familiar

with the concepts and terminology of wireless local area networks. MCPE-1924

Installation

MCPE-1924 Installation

Packing List

Before you start to install the ODU, make sure the package contains the

following items：

● Wireless Outdoor CPE (Customer premise unit)

●Mounting Kit * 1

●Power Over Ethernet Kit * 1

●Ground Connection * 1

● 2.5” /4” U bolts * 1 and Anchor * 4

● RJ-45 Conector (1.5M) * 1

Hardware Installation

Once you check off everything from the package, you can start to install the

ODU. You can mount to a pipe, a pole or to the side of a building. The

steps are showed in the following：

1. You must mount the ODU into the L bracket first.

Note: ALL the 4 screws had been tightened onto the ODU and

Bracket

2. You can use the U bolt to mount on the pipe, depending on

the radius of the pipe. (Wall mounting is referred to Wall Mounting

Figure) The two U bolts must be mounted tightly. Be aware of not

over-tighten the U bolt.

3. After checking the ODU is mounted well, you can connect the following

two cables: the Waterproof RJ-45 network cable to “P+ DATA OUT”

port of ODU and the RF cable to antenna port. Additional waterproof

tool, such as waterproof tape, is recommended to use to enhance the

waterproof function. It is suggested to have a lightening protector

between antenna and antenna port. Connecting the ground wire as

the figure of “ODU ground wire connection.”

4. Plug the other end of the waterproof RJ-45 cable to the PoE device.

The PoE device is guaranteed only in indoor environment.

Caution: DON’T plug the power cord into PoE device before you finish install

the antenna and Ground wire to ensure the safety.

If the RJ-45 cable’s length is not long enough to connect to your network

device for indoor parts installation, you can extend the cable length.

However, make sure the maximum length of the RJ-45 cable is shorter than

100M (about 109 yards) for normal operation under IEEE 802.3 standards.

When you plug the regular RJ-45 cable into the PoE device, you should use

the regular RJ-45 cable to plug into the “DATA IN” of “Power Over Ethernet

Kit” to connect to hub/switch or use the crosslink RJ-45 cable (Not included

in the Packing List) to connect with user’s PC.

The waterproof RJ-45 cable must be connected to the “P+DATA OUT” port.

Caution: Be careful! Don’t plug the two cables inversely. It will damage the

devices!

We recommend you refer to the following illustration as a guideline for

hardware installation.

Ch 2. First Time Configuration

Before Start to Configure

There are two ways to configure the device, one is through web-browser,

and the other is through Secure Shell CLI interface. To access the

configuration interfaces, make sure you are using a computer connected to

the same network as the device. The default IP address of the device is

192.168.2.254, and the subnet-mask is 255.255.255.0.

The device has three operation modes (Router/Bridge/WISP). In bridge

mode, also known as AP Client, you can access the device by both WLAN

(Wireless Local Area Network) and wired LAN. And in router/WISP modes,

the device can be accessed by both WLAN and WAN. The default IP

addresses for the device are 192.168.2.254(for LAN), 172.1.1.1(for WAN),

so you need to make sure the IP address of your PC is in the same subnet

as the device, such as 192.168.2.X (for LAN), 172.1.1.X (for WAN).

Please note that the DHCP server inside the device is default to up and

running. Do not have multiple DHCP servers in your network environment,

otherwise it will cause abnormal situation.

We also provide an auto-discovery tool which is for finding out the IP of the

device. In case, you’ve forgot the IP of the device or the IP of the device has

been changed, you can use the tool to find out the IP of the device even your

PC is not in the same subnet as the device is.

Knowing the Network Application

MCPE-1924 can act as the following roles, and it supports WDS (Wireless

Distribution System) function.

 Access Point

 WDS (Wireless Repeater)

 Bridge/Router

 WISP

 AP Client

The device provides 3 different operation modes and the wireless radio of device

can act as AP/Client/WDS. The operation mode is about the communication

mechanism between the wired Ethernet NIC and wireless NIC, the following is the

types of operation mode.

Router

The wired Ethernet (WAN) port is used to connect with ADSL/Cable modem and

the wireless NIC is used for your private WLAN. The NAT is existed between the 2

NIC and all the wireless clients share the same public IP address through the WAN

port to ISP. The default IP configuration for WAN port is static IP. You can access

the web server of device through the default WAN IP address 172.1.1.1 and modify

the setting base on your ISP requirement.

Bridge

The wired Ethernet and wireless NIC are bridged together. Once the mode is

selected, all the WAN related functions will be disabled.

WISP (Wireless ISP)

This mode can let you access the AP of your wireless ISP and share the same public

IP address form your ISP to the PCs connecting with the wired Ethernet port of the

device. To use this mode, first you must set the wireless radio to be client mode and

connect to the AP of your ISP then you can configure the WAN IP configuration to

meet your ISP requirement.

The wireless radio of the device acts as the following roles.

AP (Access Point)

The wireless radio of device serves as communications “hub” for wireless clients

and provides a connection to a wired LAN.

AP Client

This mode provides the capability to connect with the other AP using

infrastructure/Ad-hoc networking types. With bridge operation mode, you can

directly connect the wired Ethernet port to your PC and the device becomes a

wireless adapter. And with WISP operation mode, you can connect the wired

Ethernet port to a hub/switch and all the PCs connecting with hub/switch can share

the same public IP address from your ISP.

WDS (Wireless Distribution System)

This mode serves as a wireless repeater; the device forwards the packets to another

AP with WDS function. When this mode is selected, all the wireless clients can’t

survey and connect to the device. The device only allows the WDS connection.

WDS+AP

This mode combines WDS plus AP modes, it not only allows WDS connections but

also the wireless clients can survey and connect to the device.

The following table shows the supporting combination of operation and wireless

radio modes.

Bridge Router WISP

AP V V X

WDS V V X

Client V X V

AP+WDS V V X

Hereafter are some topologies of network application for your reference.

Bridge Mode

With

Bridge Mode

With

WDS + AP

Bridge Mode

Router Mode

With

WDS + AP

WISP Mode

Internet

Broadband

Modem

Table des matières

Manuels Antenne populaires d'autres marques

Alfa Network

Alfa Network APA-L01 Manuel utilisateur

Naval

Naval PR-422CA Manuel utilisateur

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manuel utilisateur

TERK Technologies

TERK Technologies TV44 Manuel utilisateur

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manuel utilisateur

HP J8999A Manuel utilisateur

MobilSat

MobilSat MSP-S Manuel utilisateur

Steren

Steren ANT-UHF 13 Manuel utilisateur

Novatel

Novatel 600-G Manuel d'utilisation

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manuel utilisateur

TRENDnet

TRENDnet TEW-AO12O Manuel utilisateur

Radio Shack

Radio Shack 15-1837 Manuel utilisateur

CommScope

CommScope CMAX-OMFX-43M-I53 Manuel utilisateur

Ramsey Electronics

Ramsey Electronics DAP25 Manuel utilisateur

COBHAM

COBHAM SAILOR 800 VSAT Manuel d'utilisation et d'entretien

Trango Systems

Trango Systems AD900-9 Manuel utilisateur

Steren

Steren ANT-100 Manuel utilisateur

Proxim

Proxim 5054-PA-23 Manuel utilisateur