Seek Thermal FirePRO 300 Manuel utilisateur

User Manual

FirePRO 300

Thermal Imaging Camera

May 2023

REV 1

1INTRODUCTION ......................................................................................................... 3

2QUICK START GUIDE................................................................................................ 5

3GETTING TO KNOW YOUR FIREPRO 300.............................................................. 6

4OPERATION AND USE.............................................................................................. 2

5MAINTENANCE AND CLEANING............................................................................. 6

6TRAINING.................................................................................................................... 7

7CUSTOMER AND PRODUCT SUPPORT ............................................................... 10

8LEGAL AND WARRANTY........................................................................................ 11

1Introduction

Thank you for choosing Seek Thermal. The FirePRO 300 is a dependable situational

awareness thermal imaging camera designed by firefighters, for firefighters. We hope

you find this thermal imaging camera to be the most efficient and effective tool in your

arsenal and we look forward to continuing to support the fire service community

worldwide.

1.1 How to use these instructions

Ensure that each person who uses the product has read and understood this user

manual before using this product. Failure to do so can result in serious injury or death.

Follow all the instructions. This will avoid fire, explosions, electric shocks, or other

hazards that may result in damage to property and/or severe or fatal injuries. Keep all

safety information and instructions for future reference and pass them on to subsequent

users of the product.

Seek Thermal is not liable for cases of material damage or personal injury caused by

incorrect handling or non-compliance with this user manual. In such cases, the warranty

will be voided.

For more information contact:

Seek Thermal Inc.

6300 Hollister Ave

Santa Barbara

CA 93117

www.thermal.com

www.thermal.com/support

1.2 Intended use and reasonably foreseeable misuse

This product is intended to be used as a personal safety aid. Never become wholly

dependent on the thermal imager for personal navigation. It is not a substitute for proper

safety training. Always maintain awareness of location and escape routes when using

this device. Failure to do so may result in serious injury or death.

The product may only be used in accordance with the instructions described in this

manual. Any use other than those described in this manual is considered as non-

intended use. This will also invalidate the warranty.

1.3 Online documentation

We update our user manuals regularly. The latest version of the documentation is

available at www.thermal.com/support

1.4 Other languages

This is the English user manual. Manuals in other languages are available upon

request.

2Quick Start Guide

Please refer to the following to start using the product right away:

1. Before first time use, charge the FirePRO 300 using the supplied charging dock for

3.5 hours or until the charge screen indicates full battery.

2. Push the Power button to turn the camera on. The camera will start imaging within 7

seconds.

3. Aim the front of the camera lens toward the scene of interest.

4. To change modes; press and hold the Mode/Flashlight button for 3 seconds. The

modes will cycle through in the following order: TI Basic, TI Basic+, Survey. A mode

icon indicator will appear in the bottom left of the screen for TI Basic+ and Survey

mode. Please refer to the Camera Modes section for detailed descriptions.

5. To turn flashlight on/off; press and release the Mode/Flashlight button.

6. To capture images; press and release the Media Capture button. To capture video;

press and hold the Media Capture button for 2 seconds. A red recording icon will

appear in the bottom left of the screen. Press the Media Capture once to turn off

video recording.

7. To transfer image and video files, connect the dock to a Windows or MAC computer.

8. To change the temperature units between Fahrenheit and Celsius, insert the tip of a

pen into the pin hole situated between the Power button and Mode/Flashlight button.

3Getting To Know Your FirePRO 300

3.1 What’s included in the box

•Thermal imaging Camera

•Charging dock

•USB-C to USB-A cable

•Hook and loop retaining strap

•Durable Quick Start Guide

•Safety information booklet

3.2 Equipment ratings

Battery Material

Lithium-ion

Nominal Voltage

3.6 V

Nominal Capacity

3500 mAh

Environmental

Intended for wet locations (camera)

Intended for outdoor use (camera)

Intended for indoor use (charger)

10 ~ 95 % RH, non-condensing

Overvoltage Category OCV: 1

Pollution Degree 2

Altitude

Camera: 5000m. Desktop: 5000m (Warning: Overall altitude is

dependent upon the altitude rating of the AC/DC adapter used

to provide the 5Vdc source).

Operation and

Storage

Temperature

Storage: -20℃ to +60℃

During discharge: -20℃ to +60℃

During Charge: 0℃ to +45℃

Charger Input

Rating

5VDC, min 1.0A (USB Type C connection)

Only for use with a USB AC/DC charger or USB computer host

with a 5Vdc output which is rated LPS or Class II.

IP Rating

IP67 (camera), IP20 (charger)

3.3 Camera elements

Figure 1 –Front camera view

Figure 2 - Rear camera view

1. Power On / Off

2. Image and Video capture

3. Flashlight / Mode selection

4. F to C unit change button

5. 320 x 240 LCD display

1. LED flashlight

2. Thermal imaging sensor and

lens

3. Lanyard attach point (sold

separately)

4. Charging contacts

3.4 Screen elements

1. Over temperature indicator; provides a visual

warning that the thermal imaging camera is

close to the overheating of internal

components. Move the camera to a cooler

location

2. Color reference temperature bar

3. Battery status indicator

4. Temperature reticle (when TI BASIC+ or

Survey mode are enabled)

5. Temperature measurement reading, displays

the temperature measured at the center

reticle location (when TI BASIC+ or Survey mode

are enabled)

6. TI BASIC+ icon, indicates that the extra

featuresof TI BASIC+ are enabled; Using the

camera in TI BASIC+ mode may require

additional training

7. Survey Mode icon. Indicates that the extra

features of Survey mode are enabled; Using

the camera in Survey mode may require

additional training

3.5 Battery status indicator (operational)

4Operation and Use

4.1 Charging the device

1. Place the charging dock on suitable stable surface.

2. Plug the USB cable into a safe power block (not provided) or computer USB port.

3. Place the FirePRO with the screen facing upwards and the charging contacts

facing downwards into the dock.

4. The screen on the FirePRO will indicate battery status within a few seconds.

Figure 3 - Camera and charging dock

NOTICE

Charge time for a fully depleted battery is 3.5 hours.

NOTICE

Charging the camera using a computer may take considerably longer than using a

separate USB power block.

NOTICE

The charger is suitable for indoor use only.

Clean the charging contacts periodically. See Section 5 for more information.

CAUTION

This desktop charger is intended to be mounted on a flat and stable surface in a

suitable location where there is no risk of physical impact or acceleration forces.

Table des matières

Autres manuels Seek Thermal Caméra thermique

Seek Thermal

Seek Thermal Reveal Series Manuel utilisateur

Seek Thermal

Seek Thermal Reveal FirePRO Manuel utilisateur

Seek Thermal

Seek Thermal FirePRO 200 Manuel utilisateur

Seek Thermal

Seek Thermal Reveal FirePRO Guide d'installation

Seek Thermal

Seek Thermal Seek Scan Manuel utilisateur

Seek Thermal

Seek Thermal FirePRO Series Manuel utilisateur

Seek Thermal

Seek Thermal Reveal FirePRO Manuel utilisateur

Seek Thermal

Seek Thermal AttackPRO FQ-PAAX Manuel utilisateur

Seek Thermal

Seek Thermal Seek Scan Manuel utilisateur

Seek Thermal

Seek Thermal RevealPRO Manuel utilisateur

Manuels Caméra thermique populaires d'autres marques

Hikmicro

Hikmicro B20 Manuel utilisateur

FLIR

FLIR E-EST Series Manuel utilisateur

FLIR

FLIR M-Series Manuel utilisateur

BST

BST BT-72 Manuel utilisateur

FLIR

FLIR G300 pt Series Manuel utilisateur

CBC

CBC EN7-S02T Manuel utilisateur

Satir

Satir YRH600 Manuel utilisateur

TESTO

TESTO 882 Manuel utilisateur

TECPEL

TECPEL TIG-320 Manuel utilisateur

SKF

SKF TKTI 21 Manuel utilisateur

TESTO

TESTO 885 Manuel utilisateur

InfiRay

InfiRay AT300 Series Manuel utilisateur

InfiRay

InfiRay AT Series Manuel utilisateur

FLIR

FLIR X6530sc Series Manuel utilisateur

Videotec

Videotec MAXIMUS MVXT Manuel utilisateur

Guide Sensmart

Guide Sensmart D384M Manuel utilisateur

NBN

NBN FLIR A6 Series Manuel utilisateur

WORKSWELL

WORKSWELL SAFETIS Manuel utilisateur