Seedsware TMG-310-DC00-01 Manuel utilisateur
16A4A4-00007E-1
TM Model “G”
Gesture Model
Touch Screen Monitor
TMG Series
Instruction Manual
10.4”TMG-310-DC00-01
12.1”TMG-312-DC00-01
Seedsware Corporation
http://www.seedsware.co.jp/global/
i
Introduction
Thank you for choosing Seedsware products.
This manual describes the functions of the TMG series.
Please read this manual carefully and use the product correctly.
Product will be referred to as “TM”hereinafter.
Copyrights and Trademarks
■The copyright of this instruction manual is rightfully owned by Seedsware Corporation.
■Reproduction and/or duplication of this product and/or this manual, in any form, in whole or
in part, without permission is strictly prohibited.
■Contents of this product and/or this manual are subject to change without previous notice.
■Although all efforts have been made to ensure the accuracy of this product and/or the
contents of this manual, should you notice any errors or have any questions, feel free to
contact and notify us.
■Seedsware shall not be held liable in any way for damages or losses, nor be held
responsible for any claims by a third party as a result of using this product.
■Other product and company names mentioned herein may be the trademarks of their
respective owners.
Precautions for Safe Use
Please go through and follow the below precautions before use.
Safety Symbol Legends
Safety symbols listed below are noted throughout this manual for the TM to be used correctly.
These symbols stand for very important safety information as noted below:
Warning
Indicates a procedure, condition, or statement that, if not strictly observed,
could result in severe human injuries or loss of life.
Caution
Indicates a procedure, condition, or statement that, if not strictly observed,
could result in human injuries or property damage.
Indicates a procedure, condition, or statement that is strictly prohibited for
correct use of the equipment. (Forbidden)
Indicates a procedure, condition, or statement that should be strictly followed
for correct use of the equipment. (Mandatory)
ii
Warnings
Warnings for Design
Designing switches that might cause human injuries and/or property damage on the touchscreen is
strictly prohibited. Unintentional output signals due to malfunction of the main body, units, and/or
cables can cause serious injuries. Design the system so that switches with major functions are
equipped on devices other than the TM itself.
Designing safety related switches on TM is prohibited. Switches related to safety, such as emergency
stop switches, should be made on a different hardware.
Do not use TM as a major warning system that may cause injuries/serious material damages, and or
production stoppage. Control devices related to critical warning displays and warnings should be
structured on an independent, redundant hardware system or a mechanical interlock.
TM is not intended for use for aircraft equipment, aerospace instruments, trunk line communication
equipment, nuclear power control equipment, and medical equipment that concerns life support, and
or other equipment that concerns high reliability and safety. It cannot be used for these purposes.
When using the TM for purposes that concern high reliability and safety functions and accuracy such
as transport equipment (trains, automobiles, ship, etc.), crime/disaster prevention devices, various
safety devices, and medical equipment that does not concern life support, be sure to have safety
features including redundancy and false operation prevention measures incorporated into the entire
system.
Display will black out when the backlight goes out. If mistakenly operated in this condition, it might
result in improper operation. Do not design touch-switches that might cause human injuries and
material damages on the TM.
Warnings for Handling
Do not modify/disassemble the TM. It may cause fires and/or electric shocks
Do not use around flammable gas. It may cause explosions.
Do not put any kind of liquid, such as water, and metals into the product. It may cause fire and/or
electrical shocks.
In an event abnormality is detected such as smoke, unusual odor or abnormal noise, disconnect the
power plug and discontinue use. If continued use, it may cause fire or electrical shocks.
Warnings for Wiring
For wiring and installation, please refer to the manual and specifications in order to conduct it correctly.
It may cause fires and/or electric shocks when not done properly.
Before installing the power cable, make sure power is not being supplied from power source. It may
cause electrical shock if not followed.
Do not use power voltage other than what is specified. It may cause fires and/or electric shocks.
iii
Cautions
Cautions for Disposal
When disposing the product, please treat is as industrial waste.
Precautions for Safe Use
Do not press the display with strong pressure or hard objects. It may break the LCD panel
and cause injuries.
Please use this product within the specified ambient temperature and humidity range. If not
used properly, it may cause malfunctions.
Do not press down on the display area of TM with sharp objects such as mechanical pencils
or drivers. It may damage the display.
If the surface of TM gets dirty, wipe with a dry, soft cloth damped in a neutral detergent then
wrung dry. Do not use thinner or organic solvents.
Do not use in areas where rapid temperature change can cause condensation. It may cause
malfunctions.
In order to prevent product temperature from rising, do not use in areas where heat can be
trapped. Also prevent storing in areas of high temperature.
Do not use or store TM in locations exposed to direct sunlight, fine particles, oil smoke and
steam.
Do not use or store all precision equipment including the TM where shock or vibration can be
applied.
Do not use or store in areas where gasified chemicals are diverged into the air or where
chemical contamination can occur.
When using power source with slow rise-time and fall-time, it may not operate correctly. Be
sure to drop the voltage to 0V when turning the power back on after once turning off the
power, before turning on the power. It may not boot correctly.
iv
Handling of LCDs
1) The LCD display contains skin-irritating materials. If liquid materials flow out due to damage and
comes in contact with skin, wash the area under water for at least 15 minutes and consult a doctor.
2) The LCD display might have uneven brightness according to the contents being displayed. This is not
a malfunction.
3) Minute spots (dark or bright) may occur in the LCD display elements. This is a basic characteristic of
the LCD display and not a malfunction.
4) When LCD display is viewed outside the specified view angel, the color might seem different. This is a
basic characteristic of the LCD display and not a malfunction.
5) When displaying a same image for a long period of time, it might cause an image lag. This is a basic
characteristic of the LCD display and not a malfunction.
In order to avoid image lags, change the displayed image periodically and avoid displaying the same
image for a long period of time.
Handling of Projective Capacitive Touch Screens
1) If elements that change ambient environments or electric fields (capacitors with large capacity, power
units, and materials with high permittivity such as metals) are set close to the product, it might have
impact to the coordinate detection. Make sure to keep a good distance from the above unstable
elements as much as possible when designing.
2) Connect the FG (Frame GND) of the unit and the power. Touch screen operation may become
unstable when failed to do so.
3) Due to the characteristics of the touch screen, the operations of the touch screen might become
unstable depending on its installed environment. To use it correctly, be sure to conduct sensor
calibration at installment. Refer to “4.4 Sensor Calibration”for details.
4) The touch screen surface is made of glass. Glass is subject to break once scratched. Please handle
with care and avoid glass from coming In contact with other glass and hard objects.
5) Touchscreen may not operate correctly when there is moisture on the surface.
When moisture is detected on the touch screen surface, please wipe dry before use.
6) When designing applications, consider the fact that area slightly outsidethe display might be read as a
coordinate due to the characteristics of the touch screen.
Table of Contents
1.
Features.....................................................................................................................1
1.1 Features..................................................................................................................................... 2
2.
Product Configuration.................................................................................................3
2.1 Standard Accessories................................................................................................................. 4
2.2 Names and Functions of Each Parts........................................................................................... 5
2.3 Panel Installation........................................................................................................................ 6
2.4 Installing to Stands..................................................................................................................... 9
2.5 Wiring........................................................................................................................................10
2.6 Operations.................................................................................................................................13
3.
OSD..........................................................................................................................14
3.1 OSD Menu ................................................................................................................................15
3.2 OSD Menu Operation................................................................................................................16
4.
Touch Screen Setting Tool........................................................................................18
4.1 System Requirements ...............................................................................................................19
4.2 Installing Procedures.................................................................................................................20
4.3 Setting.......................................................................................................................................24
4.4 Sensor Calibration.....................................................................................................................26
5.
Maintenance.............................................................................................................27
5.1 Maintenance..............................................................................................................................28
6.
Troubleshooting........................................................................................................29
6.1 Display......................................................................................................................................30
6.2 Touch Screen ............................................................................................................................31
7.
Others.......................................................................................................................32
7.1 Warranty and Repair..................................................................................................................33
7.2 Production Discontinuance ........................................................................................................34
7.3 Inquiries.....................................................................................................................................35
1
1. Features
Chapter Contents
1.1 Features ...............................................................................................2
2
1.1 Features
n2 Signal input interfaces
・DVI Interface (DVI connector)
・Analog RGB Interface (D-Sub15 pin (mini) connector)
nDC power input (12V/24V) compliant
nUSB (Type B) for the touch screen interface
nLong life for industrial equipment/ high luminance LCD
nProjected capacitive touch screen as standard
・2 point touch complaint
■Can be used with gloves
*May not be possible depending on the type of gloves and/or the operating environment.
■Full flat front surface design
■Superior weather resistance with tempered cover lens
■Multi-display correspondent
■Contrast function
■Brightness adjusting function
■Product Certifications : UL61010 (UL/cUL), CE Marking (EMC Directive)
3
2. Product Configuration
Chapter Contents
2.1 Standard Accessories............................................................................4
2.2 Names and Functions of Each Parts ......................................................5
2.3 Panel Installation...................................................................................6
2.4 Installing to Stands................................................................................9
2.5 Wiring.................................................................................................10
2.6 Operations..........................................................................................13
4
2.1 Standard Accessories
・Accessory list 2pc ・Installation Guide 2pc
・Mounting Bracket 1set (4pcs) ・Power Connector 1pc
・Gasket 1pc (preinstalled to unit)
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Seedsware Écran tactile
Manuels Écran tactile populaires d'autres marques
IBASE Technology
IBASE Technology ASTUT-152-RE1S Manuel utilisateur
YASKAWA
YASKAWA TP 610C Manuel utilisateur
B&R
B&R Power Panel C Series Manuel utilisateur
Beijer Electronics
Beijer Electronics X2 control Manuel utilisateur
AXIOMTEK
AXIOMTEK GOT321W-521 Manuel utilisateur
TRIDONIC.ATCO
TRIDONIC.ATCO x-touchBOX Manuel utilisateur
