Security Centres 808 Manuel utilisateur

496336 Issue 1 1 of 22

808

Installation and User Guide

Compatible Equipment

927 8 character LCD keypad new style case

929 8 character LCD keypad

947 Portable printer ( Battery powered ) and power supply unit

949 Wall Mounted Printer Bracket

951 Printer lead

9040 16 Ohm internal sounder

9056 Plug-on Digital Communicator

Plug-on RedCare STU (manufactured by others)

9076-01/2 Signalling Interfaces

2 of 22 496336 Issue 1

Introduction

The 808 is a programmable Alarm System suitable for domestic or small

commercial premises.

The system comprises an end station in a shielded case, and up to four

separate keypads. The end station provides:

• Connections for up to eight Fully Supervised Loop (FSL) or Closed

Circuit zones (selectable during programming).

• Three outputs, two fully programmable.

• Pins for fitting a plug-on communication device. Any device that

complies with the Scantronic plug-on footprint can be fitted.

The installer can program the system from the keypad, which provides an

eight character Liquid Crystal Display (LCD). The programming interface is

arranged into a set of numbered menus that lead the installer through the

installation process.

The 808 software provides a flexible installation that can meet many different

needs. The system can provide for up to 8 identified users. The 808 allows

users to set the system to four different security Levels (for example full set

and three part sets) which can be programmed by the installer. Individual

zones can be programmed as Flexi-Zones™, which change behaviour

depending on which security Level is set.

The 927 LCD Keypad

Figure 1. 927 Operator Controls and Displays

The 927 LCD keypad provides an eight character super twist LCD display, a

green Power LED, and four red Level status LEDs. The 927 also provides

terminals for one zone, in addition to those supplied by the end station.

8 Character Liquid

Crystal Display

Optional programmable

panic alarm keys. Press

keys 1 and 3 together

Optional programmable

control function keys.

Press keys 7 and 9

together.

Menu and Enter keys

Levels A to D LEDs

(Set or Unset)

Scroll and Level

setting keys

Edit Keys

Keyboard with

backlit soft rubber

keys

Power

808

496336 Issue 1 3 of 22

Technical Specification

General

Operating temperature = -10º - +40ºC.

Humidity = 80% RH.

Dimensions (end station) = h x w x d 300 x 300 x 80mm.

Weight (end station) = Approximately. 5Kg.

Power Supply

System Power Supply

(Ambient Temp. 20 º. C) = 900 mA.

With the system quiescent, this supply is used as follows:

808 end station = 90 mA.

Each Remote Keypad = 60 mA.

The remaining current is available for recharging the battery, and supply

attached devices through the 12V Aux terminals on the main connector.

With the system in alarm the battery can supply current additional to the

maximum available from the system power supply.

Output Protection

Self resetting thermal Polyswitches protect outputs at the following levels:

12V Aux =1,350mA.

Keypad12V = 500mA.

Siren = 750mA.

Batt (reverse connection) = 2,500mA.

Bell, Strobe and OP1 are open collector outputs rated at 500mA.

Battery

StandbyBattery = 12 Volt, 6.5AH rechargeable lead-acid, Gel

Typebattery.

BatterySpace = h x w x d 150 x 110 x 75 mm.

Keypad Wiring

Recommended maximum distances for the remote keypads from the end

station, using standard alarm cable is 100 metres per branch for the star

configuration.

For a daisy chain configuration the maximum length must take account of the

number of keypads sharing the cable. In general, a single keypad can be

connected at the end of a maximum of 300m of standard cable. If you wish to

connect more keypads the cable must be shorter, or the 0V wire must be

thicker. The criterion is that at the last keypad the voltage between 0V and

12V wires must be no less than 10.5V.

808

4 of 22 496336 Issue 1

Zone Wiring

The recommended maximum distance for FSL zones using standard alarm

cable is 200m - 300m.

Software Limits

The 808 can support:

• One to four Levels.

• Four Areas in total.

• Eight zones provided by the end station PCB plus one zone pro-

vided by each keypad.

• Three outputs provided by the end station PCB.

• Four Flexi-Zones per Level.

• 8 User codes, including one Supervisor.

Keypads

Before connecting the keypad(s) to the system, the engineer must program

an identification number into the NVM chip on each keypad. Each keypad in

a system must have a different address number to ensure that the end

station can correctly identify them. The keypad sounder, back-light and LCD

display can also be tested and setup at this stage.

927 Keypad Address

1. Set the ‘Prog’ switch on the keypad PCB to ‘On’ and the ‘Test’ switch to

‘Off’.

2. Connect the 0V and +12V terminals to a 12 V DC supply, for example a

chargedbattery.

The display shows the software number of the keypad. Take note for

future reference.

3. Press ‘Enter’ twice.

LED 1 lights and the display shows the current keypad address, for

example: 1- 1

4. If the display does not show the correct keypad address, enter the new

address by entering a 1-digit number between 1 and 4, for example 2

for the second keypad.

The display shows the new keypad address.

Zone Wiring 808

496336 Issue 1 5 of 22

Enabling/Disabling Keys, Display and Sounder

5. Press ‘Enter’.

LED 2 lights and the display shows the status of the keypad sounder: 0

for sounder ‘ON’ or 1 for sounder ‘OFF’, for example: 2- 0

6. Change the keypad sounder status as required by entering 0 or 1.

(The keypad sounder is normally left at ON = ‘ZERO”).

7. Press ‘Enter’.

LED 3 lights and the display shows the current status of the keypad

back-light: 0 for timed or 1 for back-light always ‘ON’, for example: 3- 1

8. Change the back light status as required by entering 0 or 1.

9. Press ‘Enter’.

LED 4 lights and the display shows current keypad keys status: 0 for

Active or 1 for Inactive, for example: 4- 0

10. Change the keypad status as required by entering 0 or 1. (The keypad

keys are normally left active = ‘ZERO’.)

11. Repeat 1 to 10 for any other keypads connected.

12. Set the ‘Prog’ switch to OFF and remove power to the keypads to lock

the address and options into the keypad(s).

808 Enabling/Disabling Keys, Display and Sounder

6 of 22 496336 Issue 1

Wiring

The 808 main PCB has facilities for connecting:

Four keypads.

Eight 2-wire FSL detector zones or eight 4-wire closed circuit zones.

Siren (Loudspeakers).

Three outputs.

Figure 2 shows the control unit connector.

Zone 8 CCT 8

A/T 8

Zone 7

CCT 7

A/T 7

Tamper return

Siren

12V

Bell (OP1)

OP2

OP3

+ve

-ve

Outputs

12V Aux

+ve

-ve

SRQ

12V

Sig

Keypads

Zone 6 CCT 6

A/T 6

Zone 5

CCT 5

A/T 5

Zone 4 CCT 4

A/T 4

Zone 3

CCT 3

A/T 3

Zone 2 CCT 2

A/T 2

Zone 1

CCT 1

A/T 1

Figure 2. 808 Main Connector

Wiring 927 Keypads

All keypads must be connected to Keypad terminals on the main PCB or

"daisy chained" to other keypads. Figure 3 shows the connections for each

keypad.

808

496336 Issue 1 7 of 22

I/P

SND

SIG

SRQ

+VE

Prog

Test 1

Vol

Display

Rear of keypad pcb

Tamper

N/O Exit

Terminate

Button or

N/C Lock Set

Switch

End Station

Connections

SIG

SRQ

Extension Piezo

12VDC

E.E. Sounder

25mA Max. +

To other

keypad(s)

FEZ

To detector

Figure 3. Wiring the 927 Keypad

Important: Please do not connect other devices (for example SAB, speakers and so

on) in the same cable as the remote keypad wiring.

Wiring Detector Zones

The 808 main connector has terminals for eight detector zones. Zones can

be wired as either two wire Fully Supervised Loop (FSL) or four wire Closed

Circuit (CC). However, all eight zones must be of the same circuit type. The

factory default is for CC zones. Use Menu 21 to change between FSL or CC.

Wiring FSL zones

Each FSL zone uses a two wire closed loop, with two resistors of different

values to differentiate between a ‘Circuit’ and ‘Tamper’ signals. A 2K2 (2.2

kohms) resistor is fitted in series at the end of the wired loop (EOL-End-Of-

Line) and a 4K7 (4.7 kohms) resistor fitted across the alarm contact. All

tamper devices are connected in ‘Series’ with the return feed to the end

station, see Figure 4.

808 Wiring Detector Zones

8 of 22 496336 Issue 1

2k2 EOL

4k7

Zone 1

CCT

Alarm contacts

Tamper Loop

Zone 1

Note: When wiring FSL zones, link out the

anti-tamper terminals of each zone in use

on the main connnector and expander

cards.

Figure 4. Wiring Diagram for Single Alarm Contacts and Tamper Wiring

With the loop in a normal state and the alarm contacts closed (shorting out

the 4K7 resistor), the total resistance of the loop is 2K2 ohms. When the

alarm loop is opened and the short removed from the 4K7 resistor, the

resistor is brought into the circuit and the resistance of the loop is increased

to 6K9 causing the end station to detect an alarm condition. If a tamper

device is opened, the loop resistance will be open circuit and the end station

will detect a tamper signal.

The wiring resistance should be restricted to a maximum of 100 ohms. The

recommended maximum cable distance per zone is 200 - 300 metres.

Programming

Initial Power Up

Note: Depending on the status of the system when it is powered-up, e.g., open

tampers etc., some screens may differ from those shown below.

1. Apply battery power first, then connect the mains.

The keypad display shows the Software version number followed by the

date.

After 3 seconds, the display shows the time: 16:07

2. Key in the factory default user code (1234) and press Enter.

The display shows one of the following messages depending on how

the system is currently set up: SYS DIS RST REQ

3. Key-in the factory default installer code zero (0) + 7890,

then press Menu.

The display shows: MENU NO OR LEVEL

Programming 808

496336 Issue 1 9 of 22

4. Press 0.

The display shows: 0:INST PROG

5. Press Enter.

The display prompts you to remove the end station lid: REMOVE LID

6. If the end station Tamper Switch is already open, close and open it

again.

You have now reached the Installer programming

mode. The display shows: 00-PROG SYSTEM

Finding Menu Items

The 808 programming is divided into sets of numbered menus. Each menu

starts with a two digit number. The menus are grouped together into the

followingcategories:

Menu No Category

00 Start point for Installer programming.

01, 04, 09 Software version, Testing, and Printing.

10, 11 Account Name.

20, 21 Zone circuit type.

31 - 32 Zone and Area Programming.

40 - 47 Level and keypad Programming.

50 - 53 Output Programming.

60 - 67 SystemOptions.

For a complete list of Menus and options see the next two pages.

808 Finding Menu Items

10 of 22 496336 Issue 1

Programming Chart 808

Allocate Areas to Levels

Allocate keyzones to Levels

Allocate Exit Mode

Set Exit Time

Set Entry Time

Select Alarm Type

Assign Entry/Exit tones to

keypads

Enable/Disable keys 1&3 (PA)

and

keys 7&9 (Control)

Change zone circuit type to FSL

21:zone expander

options

20: zone

expansion

11: edit name

10: Account

name

31: zone names

32:zone options

41: level

allocation

42: level

exit mode

43: level entry time

44: level

flex zones

45: alarm response

46: level rearm

operations

47: keypad

allocations

40: program

multi-flex

Select zone type

Allocate zone to Area

Select zone attribute

30: program

zones & areas

ENTERENTER ENTER ENTER

ENTER

Show software version

Test outputs, speaker, sounder

and keypad sounder

00:program

system 01:display panel

version number

04:test options

walk test ?

TEST OUTPUTS ?

ENTER ENTER

NOTE:

Except where shown, move

between menus by using the

up and down keys. At the

points marked press the

Enter key. ENTER

Table des matières

Autres manuels Security Centres Système de sécurité

Security Centres

Security Centres TS2000 Manuel d'utilisation

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur