secureView MDVR-J200 Manuel utilisateur
Read before installation
If ONLY RED LED stays on (no flashing), the device is under
OTA (Off-the-air) firmware upgrade. Please DO NOT power
off and wait patiently. It may take about 5 minutes. The
device will reboot automatically after firmware upgrade.
Make sure the SIM card and Micro SD card is inserted
properly. Gold contacts face up, cut corner inside.
SIM card and Micro SD card sockets are Push-in-Push-out
type, do not use any tools to extract the card.
Optus network is preferred. (Optus, Amaysim…etc)
For safety reason, remote fuel cut-off cannot be activated
when the car is moving.
Model: MDVR-J200
3G/WiFi In-Vehicle Surveillance & GPS Tracking System
Quick Start Guide
Thank you for purchasing the Securview Vehicle Surveillance & Tracking System
This Quick Start Guide covers basic setup, installation and use of your surveillance system.
For more information, please visit: www.securviewcctv.com
Included Components
Surveillance/GPS system & mounting cradle + Screwdriver
External backup battery
Power wiring harness
SOS alarm button
12V 40A relay & relay cable
*** Please contact us if you need 24V relay
2 x 3M adhesive mount
v
1.3-20190418
2
MDVR-J200 Quick Start Guide
1.1 System Diagram
1. Overview & Installation
Internal Camera External Camera
IR LED
640 x 352, 30fps
Micro USB
connector
1920 x 1080, 30fps
Status Indicators
Power GPS GSM
Light Sensor SIM & Micro SD Connector
The SIM card and Micro SD card sockets are Push-in-Push-out type. Do not use any tools to
extract the card.
3
Visit www.securviewcctv.com for support
1.2 Technical Specifications
Model
MDVR-
J200
Camera
Camera Style
Mobile Dual Lens Camera, infrared driver facing lens
Resolution
Road facing: 1080p (1920 x 1080) / Driver facing: (640 x
352)
Angle of View
Front: 140° (adjustable) / Rear: 90°
Focus
Fixed
Frame Rate
30fps
Features
CPU
ARM Cortex A7 Quad Core 1.2GHz
Band
GSM 850/900/1800/1900 WCDMA
850/900/1900/2100
G-Sensor
9 axis-motion
Live View
In-car / front car live video via app or web
Audio
Built-in speaker & microphone
WiFi
Frequency 2.4GHz, hot spot
Bluetooth
BT4.0 ( Android platform only)
Micro SD storage
Max. 32GB(FAT32 format)
Battery
External 450mAh
Audio
Built-in microphone / Built-in speaker
Interface
OBD Interface
Connect by power cable
USB Data Interface
(Engineering Purpose Only)
Micro USB 5 Pin
Not for data backup
Housing
Plastic
Power Input
12 - 24VDC
Dimensions
109 x 69 x 52mm
Weight
0.23kg
Operating Environment
-20° to 75°C / RH95% (max)
4
MDVR-J200 Quick Start Guide
1.3.1
Wiring
Connect cables according to the wiring diagram 1.3.2. Connect the power cable B+ (Red wire) and GND (Black
wire) to the vehicle battery’s +12V/+24V terminal and negative terminal respectively. Connect ACC (Yellow wire)
to the vehicle’s ON position . The device should power on automatically after the vehicle engine is started.
Remember to connect the backup battery module.
1.3.2
Wiring Diagram
1.3.3
Micro SD and SIM Card
While the system is off, insert the Micro SD card into Micro SD slot and an active SIM card into the
SIM slot (both located on one side of the camera).
After inserting both cards, screw on the card cover with the provided screw & screwdriver.
1.3.4
Status Indicator Lights
Power Indicator - RED
Solid red
ACC ON & Power on
0.1s ON & 10s OFF
ACC OFF
Off
Power not connected
GPS Indicator - GREEN
Solid green
ACC ON & Positioning successful
0.1s ON & 1s OFF
Searching for GPS signal
Off
ACC OFF
GSM Indicator - BLUE
Solid blue
ACC ON & Connected
0.1s ON & 1s OFF
ACC ON & No network/SIM card
Off
ACC OFF
1.3 Installation
5
Visit www.securviewcctv.com for support
Must Read Information for Installers
1.3.5
First time GPS positioning - Tricks to make positioning quicker
GPS positioning for the first time takes a bit longer time when the device is installed. It may take about 5-10 minutes. Follow
the steps below to initialize the GPS for quicker positioning:
1) Switch ON the engine.
2) Wait until the Red, Green and Blue LEDs on the device all stays on steadily (no flashing), that’s mean the GPS and
mobile signal are ready.
3) Turn OFF the engine and wait for 5 seconds.
4) Switch ON the engine again.
5) The new position should be updated when all LEDs are all on steadily.
Note: If the power of the device is disconnected and the device is moved to another new location when the device is off,
always do the initialization steps above.
1.3.6
Choosing the right mobile phone card
1) Must use Micro SIM or Nano SIM with Micro SIM adaptor.
2) Must use 4G SIM cards (4G+3G). Don’t use 3G SIM cards (3G+2G).
3) Must have data, voice, and SMS capabilities.
4) Must be able to monitor the usage, check the balance and recharge remotely by App or web site.
1.3.7
Car status update
All driving data and car status are uploaded to the web server, there is some delay between the car status on the web
server and real situation. For example, when the car switches its engine ON/OFF, its on/off status will be updated on the
web server within 3 minutes.
1.3.8
Vibration sensor sensitive
Vibration is inevitable during driving. For example, poor road conditions, humps and unintended shock on the device itself...
If the Vibration Alert triggers frequently, you may adjust the sensitivity of the vibration sensor on the App. If this features is
not need, you can also turn it off.
To enable/disable vibration alert, select “Vibration Alert” in Setting menu.
To adjust vibration sensitivity:
Click the Device List and
select the vehicle to set.
Then click “Setting”.
Select “Vibration Albert”
Slide the slide bar to adjust
and click “Save” when finish.
1.3.9
SOS button
SOS button will activate only if the button is pressed and held down for more than 3 seconds. Must enable SOS in
“Setting” menu.
6
MDVR-J200 Quick Start Guide
2.1 Automatic & Event Recording
2.2 System Usage
2. Operation
2.1.1
Automatic Recording
ACC ON - The system will power on and record automatically.
ACC OFF - The system is in sleep mode and will not record.
Recordings will be saved onto the micro SD card every 3 minutes, under the directories:
DVRMEDIA/CarRecorder/GENERAL (road camera)
DVRMEDIA/CarRecorder/USB (driver camera)
NOTE: When the Micro SD card is full, old footage on the card will be overwritten.
2.1.2
Event Recording
If a strong vibration is detected (from a crash, for example), an additional 15s will be recorded and then stored in a
separate location under
DVRMEDIA/CarRecorder/EVENT
The EVENT folder stores 1GB of footage. Old recordings in EVENT will be overwritten when the folder is full.
2.2.1
SIM Card Usage
This system is intended for use with a SIM card, but can still function as a mobile video recorder without one. Refer
below to see what the system can do with and without a SIM card:
SIM Required
•
Remote Live View
•
Remote GPS Tracking
•
Remote Picture/Video Capture
•
Push Notifications (Geo-fence, vibration alert, etc.)
SIM Not Required
•
Automatic Recording
•
GPS History Logging
•
Event History
•
Media Synchronisation
2.2.2
App & Web Usage
The system can be accessed, monitored and configured via mobile app and web browser. Visit www.car-matrix.com for
web version.
7
Visit www.securviewcctv.com for support
3.1 App Introduction
3. Configuration
Your vehicle monitoring system can be accessed, monitored and configured via mobile app.
Switch between cameras on your account on the phone.
3.1.1
App Intro
The vehicle tracking app CarMatrix, is available to download free from
iPhone App Store and Google Play Store.
This app allows for portable vehicle management, letting you perform a
variety of functions such as:
•
Real-time GPS vehicle tracking & location reporting
•
Real-time push notifications for overspeed, vibration, geo-fence etc.
•
Geo-fencing - alerts when the vehicle enters/leaves a designated zone
•
Route playback for vehicle history
•
Remote live view, playback, image snapshot & video snapshot
•
Media synchronisation for easy file transfers from recorder
CarMatrix App
Download (QR)
3.2 Account Registration
3.2.1
Account Creation
1.
Press Sign Up on the front page of the app.
2.
Enter your email address and press Next to send a verification code to your email address.
3.
Enter the verification code into the app and press Next again to finish creating your account.
3.2.2
Change Password
•
(App) Open the main menu and press the user icon next to your email address.
•
(App) Press Change Password.
•
Enter the current password, then enter your new password twice and press Save.
8
MDVR-J200 Quick Start Guide
NOTE: After account registration, you will be automatically prompted to bind
a device.
3.3.1
Adding Your Device
1.
Open the main menu and press Device List.
2.
Enter the 15-digit IMEI of your device which is printed on the box and on
the top cover of the camera. QR code scanning is under development
and will be available in later version.
3.
Enter the number plate of the vehicle and a reference name for the device
and press Next.
3.3.2
Unbinding Your Device
1.
Open the main menu and press Device List.
2.
Press the device you want to unbind, then press Unbind.
3.
Press OK to confirm.
NOTE:
MDVR-J200 cameras can only be bound to one mobile phone at a time.
If you want to register the device on another mobile phone, you must unbind the
device on the original mobile phone first.
3.3.3
Device Settings
1.
Open the main menu and press Device List.
2.
Press the device you want to unbind, then press Settings.
Device List
3.
From here, you can edit the Overspeed Alert, Driving Behaviour, Vibration Alert, LED and Voice settings of your
device.
Settings menu
Overspeed Alert settings
Driving Behaviour settings
Vibration alert settings
3.3 Binding Your Device to an Account
Autres manuels pour MDVR-J200
1
Table des matières
Manuels Système de sécurité populaires d'autres marques
EDM
EDM Solution 6+6 Wireless-AE Manuel utilisateur
Highway Safety Group
Highway Safety Group EA401 Manuel utilisateur
Siren
Siren LED GSM Manuel utilisateur
Detection Systems
Detection Systems 7090i Instructions de montage
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuel utilisateur
Siemens
Siemens FDM273 Manuel utilisateur