SecureShop SS-LK209C Manuel utilisateur
SS-LK209B/C
GPS Tracker Manual
Version 1.0
2
Preface
Thank you for purchasing this GPS tracker at Securitashop. We have
decided to make our own manual as the one we have received from
the manufacturer is hard to read. Despite our best efforts to change
this it remains below our standards which is why you receive our
own manual –with additional information on setup on platform too.
This manual shows how to operate the device smoothly and
correctly. Make sure to read this manual carefully
before using this product. Please note that specification
and information are subject to changes without prior notice in this
manual. Any change will be integrated in the latest release.
The manufacturer assumes no responsibility for any errors or
omissions in this document.
Summary
Working Based on existing GSM/GPRS network and
GPS satellites, this product can locate and monitor
any remote targets by SMS or internet. The most
advanced technology of GPS and AGPS dual positioning.
3
HARDWARE DESCRIPTION
4
Content Specifications
Content
Specifications
Dim.
120 x 64 x 35 mm
Weight
305 / 465 gram
Network
GSM/GPRS
Band
850/900/1800/1900Mhz
GPS chip
UBLOX
GPS sensitivity
-159dBm
GPS accuracy
5m
Time To First Fix
Cold status 35-80s
Warm status 35s
Hot status 1s
Car charger
12—24V inp
5V output
Wall charger
110－220V input
5V output
Battery
Chargeable changeable 3.7V
10000mAh (SS-LK209B) or 20000mAh Li-
ion battery (SS-LK209C)
Standby
90/150 days
Storage temperature
-40°C to +85°C
Operation
temperature
-20°C to +55°C
Humidity
5% - 95% non-condensing
5
SIM card installation
Open the rubber plug –Fig. 1
Insert the GSM SIM card as shown below fig. 2.
Close the rubber slip
Fig. 1
Fig. 2
Battery and Charger
Charge the battery to maximum capacity for 8-12 hours the first
time. Please use the battery and charger provided by the
manufacturer. This unit adopts built-in Li-ion battery and full battery
can standby 90 to 150 days. After first use, the battery usually
should be charged fully in 5-8 hours.
Cautions
Li-ion batteries contain harmful chemicals and may burst, please
do not bump, puncture it violently and expose it to fire.
Please charge the battery in time to keep it working normally.
6
Startup
Put the SIM card and battery in place.
Turn on the unit outdoors by pushing the button to “On”.
For first use, please initialize the unit and restore it to default
setting
In 10 or 40 seconds, the unit will begin to work and acquire the
GSM signals as well as the GPS signals. The indicator will keep
flashing every 3 seconds when the unit has received the signals.
When the unit receives GPS and GSM signals normally, you can
use it and do any setting as the instructions of this manual.
Green LED for GPRS working status
Status of indicator
Meaning
Slow flash (flash 1s after every
2s)
GSM/GPRS conversation start
Continuously in bright status
No GPRS signal
Green led off
Device fault or inactive
Blue LED for GPS working status
Status of indicator
Meaning
Slow flash (flash 1s after
every 2s)
GPS location successful
Continuously in bright status
Searching GPS signal
Blue led off
Device fault or inactive
Red LED for power charging status
Status of indicator
Meaning
red led on all the time
Charging
red led flash
Low battery
red led off
Full battery or charged full
7
Google link: click link, there is map when
positioning ok, no map means no positioning.
V:A GPS signal ok.V:V no GPS signal
2013-08-30 20:54:15: the last time receive
GPS signal.
Spd:000km/h: the speed of the tracker.
Bat:6 battery balance. Range is from 1 to 9
ID: 4102000759: ID code of device (used for connect tracking
website or APP)
S19G04；plmn：46001 GSM operator data
Lac：9516，cellid:23596 LBS data
Initialization
Send;
begin+password
in SMS to the unit, it will reply
begin ok
and
initialize all the settings. (default password:123456)
For example, send SMS: begin123456 to the tracker via a cell phone,
if succeeded, if will reply “begin ok”.
Change the password
Set Password: send sms: password+old password+space+new
password” to the unit to change the password.
For example, send sms: password123456 000000 to terminal device,
it will reply sms: password OK. New password 000000 changed in
success.
8
Make sure the new password is in 6 digits Arabic numbers or the
tracker cannot recognize the password.
Authorization
Send SMS：admin+password+space+cell phone number” to set up
an authorized number. The first authorized number should set the
other authorized numbers. If the number is successfully authorized,
the unit will reply “admin ok!” in SMS.
Send SMS：noadmin+password+space+authorized number” to
delete the authorized number.
for example, send：admin123456 13265790180 to tracker to set
13265790180 as an authorized number.
When the authorized number call the device, it will hang up your
phone and reply a real-time latitude and longitude information as
below:
Single Locating
If there is no authorized number when any number dials up the unit,
it will report a geo-info. If there is already an authorized number, it
will not respond when an
unauthorized
number calls it up.
9
Single message inquires the latitude and longitude
information, any telephone number can send instruction
”where” to the equipment, then the
equipment will reply the latitude and longitude
information to this telephone.
When an authorized number dials up the unit, it will hang up and
report a real-time Geo-info as below:
*Tracking location, When GPS signals is weak, the position of
latitude and longitude included in the SMS is the position that the
tracker received GPS signals at last. If it is different with its exact
current location, pay attention to check the time included in the SMS
you got.
Auto Track
Send SMS command “t030s005n+password” to the tracker device, it
will report the “no reply” at 30s intervals for 5 times. (s:second,
m:minute, h:hour). This command setting must be in 3 digits and
the maximum value is 255.
Unlimited times auto track: Send SMS “t030s***n+password” to the
tracker device, it will reply the “no reply” continuously at 30 seconds
intervals.
Cancellation: Send SMS “notn+password” to the tracker device, it
will report the “notn ok”.
Note: the interval must not less than 20s.
Monitor (voice surveillance)
The command to switch between track and monitor are “tracker”
and “monitor”.
The default mode is “track” (track mode).
Send SMS “monitor+password” to the unit and it will reply
“monitor ok!” and switch to “monitor” mode.
Send SMS “tracker+password” to the unit, it will reply “tracker
ok!” and restore to “track” mode.
10
Geo-fence
Set up a geo-fence for the unit to restrict its movements within an
area. The unit will send the message to the authorized numbers
when it breaches that area.
Geo-fence setup
When the unit stays immobile in a place for 3-10 minutes, the user
can send SMS:
“stockade+password+space+latitude,longitude; latitude,longitude”
to unit to set the restricted area.
Remark: The first latitude & longitude is coordinate of the top left
corner of the Geo-fence while the second latitude & longitude is the
coordinate of the bottom right corner.
Cancel geo-fence: send SMS: nostockade+password to deactivate
this function, tracker will reply nostockade ok.
Ce manuel convient aux modèles suivants
1
Table des matières
