SecuPlate ELKITW2G Manuel utilisateur
1
Quick Installation Guide
SecuPlace
2
Step 1: SIM & Panel Installation and Power-Up
NOTE: The SecuPlace system should be installed by a professional,
such as an alarm system engineer or electrician.
If the system does not have a SIM card pre-installed, install it before
applying electrical power to the control panel.
To insert the SIM card:
SIM card
access cover
(back side of
control panel)
1. Remove and
retain screw.
2. Slide access
cover outward.
3. Insert SIM
per illustration
below.
3
To mount the control panel:
WARNING: Make sure the control panel is not connected to any
electrical power supply.
X 2 X 2
4
To power-up the control panel:
. Apply electrical power to the control panel with the AC
power cable, or at the circuit breaker switch; SELECT
LANGUAGE displays on the keypad.
2. Now select the language you wish to display at the control
panel. Use to scroll to the language, and then
press .
3. Press to set for www.MyELAS.com (default);
INITIALIZING, and then DISARMED display.
NOTE: If “LOW BATTERY,” “SYSTEM NOT READY,”
“SYSTEM TROUBLE” or “TAMPER ALARM” display, there
are trouble messages (use to scroll and view them).
However, these usually resolve automatically after performing
all 4 system installation steps.
5
Step 2: Registering Kit Components
All components must be registered in order to be recognized by the
system.
Your kit comes with pre-registered components. Activate the
components to complete the registration process.
To acti ate the detectors:
NOTE: If a tamper alarm sounds
during this procedure, enter the
default master code (1234) to silence it.
•One-at-a-time, open each detector (see detector illustrations
on pages 7 and 0), and then do the following:
a. Remove the red plastic divider (battery protector strip) to
power-up the detector; a chime sounds indicating the
control panel has recognized the detector.
b. Immediately put the detector cover back on, so as not to
sound the tamper alarm. If the tamper alarm does sound,
enter the default master code (1234) to silence it.
To acti ate the keyfob:
•Press any keyfob button; a chime sounds indicating the
control panel has recognized the keyfob.
6
Step 3: Installing Kit Components
Installing the Magnetic Door/Window Contact Detector
Mounting Guidelines
Transmitter Magnet
It is recommended
to affix the
transmitter to the
frame, and to affix
the magnet to the
moving part of the
door or window.
7
To install the transmitter and magnet:
NOTE: If the transmitter is installed using adhesive strips, the back
tamper switch will not be operational.
NOTE: For installing the transmitter with adhesive strips, start at
step 4B in the following procedure.
X 4
Tamper
8
-OR-
9
Installing the PIR-Pet Detector
The wireless PIR (Passive Infra-Red) detector detects movement for
up to metres (36 feet) indoors. The Pet Immunity (PI) model is
designed to not trigger alarms by small pets that weigh up to 36
kilograms (80 pounds).
Mounting Guidelines
Avoid mounting the PIR-Pet detector in a
location where a pet can come within
reach of the detector by climbing on
furniture or other objects.
10
To install the PIR Pet detector
NOTES:
•Retain the screw for use when re-installing the CB
•Do not touch the front of the pyro sensor
•An additional battery (purchased separately) can also be used
to extend the operational duration (size ½ AA, 3.6 V, lithium)
B
B
A
X 4 X4
AScrew location
BTamper switch
CPyro sensor
C
B
Table des matières
Manuels Système de sécurité populaires d'autres marques
EDM
EDM Solution 6+6 Wireless-AE Manuel utilisateur
Highway Safety Group
Highway Safety Group EA401 Manuel utilisateur
Siren
Siren LED GSM Manuel utilisateur
Detection Systems
Detection Systems 7090i Instructions de montage
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuel utilisateur
Siemens
Siemens FDM273 Manuel utilisateur