SECO-LARM SD-994C Manuel utilisateur



 

Electric Door Strikes

Manual

Model # Operating Voltage Door Type

SD-994C 12VDC Wood

SD-994C24 24VDC Wood

SD-995C 12VDC Metal

SD-995C24 24VDC Metal

SD-994C

SD-995C

43RG

Note: This strike is not weatherproof and should only be installed indoors.

SECO-LARM Electric Door Strikes

2SECO-LARM U.S.A., Inc.





Features:

Converts cylindrical lock sets into an electronic

access-controlled locking system

Field-selectable for fail-safe or

fail-secure operation

Can be used with virtually any cylindrical door locking

system

Can use with an optional digital keypad

Suitable for office-type applications

Reversible non-handed design fits either right-hand or

left-handed doors

Shallow design for use with most metal doors

Powered by a solenoid, not a buzzer coil

For Indoor Use Only

Static strength – 1,000 lbs. (454kg)

Specifications:

Model # SD-994C SD-994C24 SD-995C SD-995C24

Operating voltage 12VDC 24VDC 12VDC 24VDC

Current draw 280m

140m

280m

140m

Operating temperature 14°~113° F (-10°~45° C)

Static strength 1,000 lbs. (454kg)

Dynamic strength 50 ft-lbs. (6.91 m-kgs)

Destructive attack Level 1

Line security Level 1

Endurance Level IV

Standby Powe

Level 1

Dimensions 715/16"x17/16"x11/4" (202x36x32 mm) 47/8"x11/4"x11/4" (124x32x32 mm)

Stainless-steel keeper for strength and long life

Non-polarized connection

Tested to 250,000 cycles (UL Tested)

The SD-994/994C24/995/995C24 is intended to be used

with UL Listed Exit Hardware

The SD-994/994C24/995/995C24 shall not impair the

intended operation of an emergency unit

The SD-994/994C24/995/995C24 shall not impair the

operation of panic hardware mounted on the door

Optional lip-extension brackets available:

oSD-995C-LE25 – 1" Extension

oSD-995C-LE50 – 2" Extension

Overview:

17/16" (36mm)

715/16"

(202mm)

75/16"

(186mm)

33/8"

(86mm) 21/2"

(64mm)

11/4" (32mm)

41/8"

(105mm)

47/8"

(124mm)

111/16" (43mm)

1/8" (3mm)

11/4" (32mm)

11/16"

(17mm)

Door Strike ....................................x 1

Mounting Plates ............................x 1

Mounting template ........................x 1

Electrical connectors.....................x 2

Trim plate ......................................x 1

Parts List:

Note: Not all parts will be used in

every installation.

Security screws .............................x 2

Black anchor nuts..........................x 2

Security Allen wrench....................x 1

Trim plate screws ......................... x 2

Mounting tabs............................... x 2

Wood screws................................ x 2

Machine screws............................ x 4

Machine screws (narrow) ............. x 2

13/4" (45mm)

SECO-LARM Electric Door Strikes

SECO-LARM U.S.A., Inc. 3







Installation:



1. Measure the latch line (see fig. 1).

a. Measure the distance between the face of

the door

amb and the face of the door latch.

This is the vertical latch distance.

b. Measure the vertical latch distance on the

door

amb from the face of the door

amb. At

that point, draw a vertical line. This is the

latch line.

2. Measure the center line (see fig. 2).

a. Measure the distance from the floor to the

center of the door latch. Ignore the location

of the deadlatch pin when taking

measurements.

b. Measure the same distance as above along

the inside of the door jamb. This is the

center line.

3. Align the included mounting template to the latch

and center lines (see fig. 3)

4. Using the template as a guide, cut into the door

jamb to a depth of

" (17mm).

NOTE: If cutting into a wooden door, use a chisel

to knock out a

" (3mm) deep cut as shown on

the template.

5. Using two of the included small screws (M4x12)

and black clips, affix the mounting tabs to the

inside of the door jamb (see fig. 4).

6. Program fail-safe or fail secure (default – fail

secure, see "Programming for Fail-Safe or Fail-

Secure on page 4).

7. Connect the two wires to the access control or

egress device, e.g. keypad, push-button switch,

push-bar, etc. using the provided electrical

connectors. Polarity is not important. Ensure that

no bare wiring is exposed.

8. Conceal all wires in the door frame. Adjust trim

plate to cover an

aps in installation. Use two of

the included large screws (M5x12) to mount the

unit to the mounting tabs. Adjust as needed to

ensure the door closes smoothly (see fig.5).

Fig.1

Fig.

Fig.3

Fig.4

Fig.5

Note: Trim plate is optional and may not be required in all installations.

Only use the trim plate to cover any gaps in the door frame.

Door latch

Deadlatch pin

Latch line

Vertical latch distance

Door jamb

SECO-LARM Electric Door Strikes

4SECO-LARM U.S.A., Inc.



Selecting Fail-Safe or Fail-Secure Operation:

Troubleshooting:

Electric strike does not activate.

Unmount the strike and check that the two wires are

connected properly.

Ensure the wires are connected to a 12 or 24VDC source.

Use a multimeter to test that the strike is receiving the

proper voltage and amperage. If it is not, it may be

necessary to use heavier gauge wires, or increase the

output of the power supply.

Make sure the activation device (keypad or push-button

switch) is working properly.

Door does not open when the

electric strike is activated.

Check that the door latch is operating properly, and

replace if necessary.

The position of the electric strike may need to be adjusted

by moving it or adding washers or shims.

Strike makes a buzzing sound. Use DC power supply instead of AC power.

1. Remove the locking screw and loosen the sliding screw.

2. Slide the sliding screw to the desired setting. Replace the locking screw and retighten both

screws.

Factor

default: Fail-saf



Fail Safe: Fail Secure:



Locking

Sliding

screw

NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason, SECO-LARM

reserves the right to change specifications without notice. SECO-LARM is also not responsible for misprints. All trademarks

rights reserved.

WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal

service for one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair o

replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is void i

damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or alteration,

improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is

not operating properly as a result of causes other than defects in material and workmanship. The sole obligation o

SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the replacement or repair only, at SECO-LARM’s

option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or property

damage of any kind to the purchaser or anyone else.

SECO-LARM®U.S.A., Inc.

16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com PITGW1

Phone: (949) 261-2999 | (800) 662-0800 Email: sale[email protected] MI_SD-99xC_190617.docx

SD-99xC Electric Strike SD-99xC Electric Strike

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels SECO-LARM Verrouillage

SECO-LARM

SECO-LARM SD-231-ND1Q Manuel utilisateur

SECO-LARM

SECO-LARM SD-997C-GCQ Manuel utilisateur

SECO-LARM

SECO-LARM E-941S 600 Series Manuel utilisateur

SECO-LARM

SECO-LARM SD-997B-1SQ Manuel utilisateur

SECO-LARM

SECO-LARM E-941SA-1K2PD Manuel utilisateur

SECO-LARM

SECO-LARM SLI E-942FC-1K3SQ Manuel utilisateur

SECO-LARM

SECO-LARM SD-993B-SS Manuel utilisateur

SECO-LARM

SECO-LARM Enforcer E-941SA-80Q Manuel utilisateur

SECO-LARM

SECO-LARM SLI E-941SA-600 Manuel utilisateur

SECO-LARM

SECO-LARM E-941S-600DPSQ Series Manuel utilisateur

SECO-LARM

SECO-LARM E-941SA-1K2PD Manuel utilisateur

SECO-LARM

SECO-LARM SLI ENFORCER 1200-lb Electromagnetic Lock... Manuel utilisateur

SECO-LARM

SECO-LARM CL-210M-U3BQ Manuel utilisateur

SECO-LARM

SECO-LARM E-946FC-600Q Manuel utilisateur

SECO-LARM

SECO-LARM SD-997A-GBQ Manuel utilisateur

SECO-LARM

SECO-LARM SD-993B-SS Manuel utilisateur

SECO-LARM

SECO-LARM Enforcer E-941DA-1K2P Manuel utilisateur

SECO-LARM

SECO-LARM E-942FC-600AR Manuel utilisateur

SECO-LARM

SECO-LARM E-941S 600DPSQ Series Manuel utilisateur

SECO-LARM

SECO-LARM E-942FC-1300 Manuel utilisateur

SECO-LARM

SECO-LARM E-941DA-600Q Manuel utilisateur

SECO-LARM

SECO-LARM E-941SA-600 Manuel utilisateur

SECO-LARM

SECO-LARM ENFORCER SD-961A-36 Manuel utilisateur

SECO-LARM

SECO-LARM SD-962H-8LAQ Manuel utilisateur

Manuels Verrouillage populaires d'autres marques

Magic

Magic 105 Manuel utilisateur

Gantner

Gantner GAT NET.Lock 7020 System Guide rapide

Wittkopp

Wittkopp Insys 7202 Manuel utilisateur

Dorma

Dorma Studio Classic Manuel utilisateur

Securam

Securam ECSL-601 Manuel utilisateur

Sudhaus

Sudhaus 3003 Manuel utilisateur

Safety 1st

Safety 1st 48517 Manuel utilisateur

Pado

Pado FDS-10 Manuel utilisateur

Esco

Esco systeQ Series Manuel utilisateur

COMPX

COMPX National D8951 Manuel utilisateur

secureo

secureo Key Box Manuel utilisateur

Stock Loks

Stock Loks C8713 Manuel utilisateur

COMPX

COMPX 1T-058 Manuel du propriétaire

Auslock

Auslock T11 Manuel utilisateur

ELCOM

ELCOM 7205 Manuel utilisateur

Stealth SAFES

Stealth SAFES ShadowVault Manuel utilisateur

Knox

Knox KeySecure 5 Manuel utilisateur

Kwikset

Kwikset 48334/01 Manuel utilisateur