Sealcom KAKADU Manuel utilisateur

KAKADU

INSTALLATION MANUAL

WARRANTY

sealcom

www.kakadu.sealcom.pl

DESCRIPTION

The "KAKADU" bell has been designed for the purpose of meeting the

expectations of even the most demanding Users. The applied technical

solutions ensure a high functionality of the bell and a wide range of

possibilities.

The bell sound is not limited to one preset signal but it can be selected

from the whole set of the signals, which allows each User for matching it to

the User's own tastes and likings. In the standard set, a wide selection of

signals has been prepared: from classical gongs and bells, through

melodies, sirens, klaxons, etc. to realistic sounds of animals. Apart from

the selection of a signal from the "factory" set, a possibility of the individual

change of the reproduced signals has been ensured, which allows a User

for unconstrained employment of the User's own invention and fantasy.

After adequate reprogramming of the bell, simultaneous definition of even

128 signals is possible.

For each programmed set of signals, three modes of bell operation are

possible:

- mode 1 - at each switching the bell on, the same signal is reproduced

(selected earlier by a user);

- mode 2 - at each switching on, a different signal, selected successively

from the programmed list, is reproduced;

- mode 3 - at each switching on, a different signal, selected at random

from the programmed list, is reproduced.

Thanks to application of the loudspeaker with a big diameter and digital

recording, a high quality of the reproduced sound has been ensured.

A modern shape of the casing fits excellently to the outfit of the interior,

both when it is installed on a wall and on a ceiling. For the User's

convenience, an easy installation has been ensured. In order to avoid a

mechanical damage of the casing while opening (due to necessity of

levering with sharp tools), a popular snap-lock was abandoned in favour

of a single screw connecting both parts of the casing.

selection of signals

operation modes

sound quality

casing

anti-lock protection

The bell is protected against the "jokers", who block the bell switch-keys in

a position "pushed in" for purpose of producing a continuous reproduction

of the signal. In the case of such treating the KAKADU bell, the signal will

be reproduced only once, and it can be started again only after release

and re-pressing the switch-key.

The bell has been adapted to cooperate with different bell wirings -

switched on both through short-circuit (Fig. 3a) and also through

supplying the voltage of ~230V (Fig. 3b). If it is possible to select a type of

wiring (for instance, in new or renovated flats), then we suggest using the

installation switch on through short circuit it does not require to be

connected to a bell and a voltage switch, which makes the bell work

independent of the power grid and eliminates any possible electric shock

(even in such extreme case as, for instance, breaking of the casing or

pulling out the switch-key from the wall).

cooperation with two types of door bell wiring

INSTALLATION

The bell is installed on the wall or a ceiling in the place, to which the wire

from the bell switch-key is delivered. In order to make a correct

installation, the following steps should be made successively:

1.Take the bell out of the package, remove a small flap and unscrew the

bolt connecting both parts of the bell (a bottom and a cover).

2.Apply the bottom to the surface, on which the bell is to be installed, in the

way ensuring that the wire of the switch-key gets into one of the cable

holes and mark with a pencil 3 longitudinal installation holes (see Fig. 1).

3.Put the bottom aside and bore the holes with a diameter of 6 mm in the

marked places, and then mount the plastic anchors, which are in the kit.

4.Screw down the bottom to the mounted anchors (through the

longitudinal installation holes) by threading the wire from the switch

through one cable holes.

CAUTION !!! In the case of installing the bell on the uneven surface, the

bolts should be screw down to the extent ensuring that the bottom will

not distort (this would make closure of the cover impossible).

Fig. 1 - BOTTOM

5.Connect the wire of the door bell push-button:

a) in the case of the wiring switched on through short-circuit (Fig. 3a)

the cores of the wire should be connected to the contacts of the

connector J3 (blue connector) - Fig. 1

b) in the case of the wiring, which is switched on through supplying of

voltage of ~230V (Fig. 3b), the cores of the wire should be connected

to the contacts of the connector J2 (red connector) - Fig. 1.

6.Close the casing and screw in the bolt connecting the bottom and the

cover.

7.Connect a battery and place it in the handle (push in) - Fig. 2.

8.Set a selected signal and a required sound level.

9.Shut the small flap.

CAUTION !!! In the case of assembling the bell in the ~230V

wiring, the connections of the wires should be performed by the

authorised person, after prior disconnecting the wiring from the

electric network.

installation hole

cable holes

connector J3 (blue)

for switching on

through short-circut

connector J2 (red)

for switching on

through supplying

of the voltage

of ~230V

door bell

push-button

Fig. 3 bell bell

door bell

push-button

a) diagram of the wiring

switched on through

short-circuit

b) diagram of the wiring

switched on through

supplying of the voltage

of ~230V

~230V

Fig. 2 - COVER

holder of the

battery

hole of the bolt

hole for sound

regulation

connector for

programming

button for

changing

a mode / signal

OPERATION

sound control

The changes in the sound level are made using the screwdriver

(cruciform). After the small flap has been removed, the end of the

screwdriver should be insert into the round hole marked with a symbol of

sound control - Fig. 2.

The regulation is made by turning the screwdriver:

more loudly - clockwise

more silently - counter clockwise

Maximum turning counter clockwise results in complete silence of the

bell.

change of the operation mode / selection of a signal

The changes of the operation mode and signal selection are made using

the push-button marked as "+", available after removing a small flap.

On each pressing of the button, a successive signal (out of the currently

programmed signals) and two special signals are reproduced. The signal,

which is heard after pressing the button, is set as a valid one. Subsequent

pressing the button changes the signal to another one and so on. After the

whole list of the programmed signals, there appear two "special signals":

- 5 short sounds it means setting the bell in the mode of reproducing the

signals, being changed successively according to the programmed list

- 1 long sound (about 2 seconds) it means setting the bell in the mode of

reproduction of the signals selected at random from the programmed

list.

Subsequent pressing the button (after "special signals") starts the

selection of individual signals out of the programmed list from the

beginning.

The battery should be replaced when the first signs of its being used up

are noticed. The fact that a battery is used up is manifested initially by the

decrease in a loudness and lower quality of the reproduced signal. Then,

(if the battery has not been replaced), in place of the emitted signal, there

appear only three short sounds, whose loudness keeps decreasing along

with progressing use of the battery till the moment of its complete decay.

In order to ensure a satisfactory time of bell operation, without a necessity

of replacement of the batteries, the use of the alkaline batteries is

recommended.

replacement of the battery

programming

Reprogramming of the bell (i.e., introducing the different signals) is made

with the help of a computer (IBM PC compatible). Necessary software is

available on the site www.kakadu.sealcom.pl (free of charge). The

computer should be connected to the bell by an appropriate connecting

cable:

- in the computer to the printer port (LPT)

- in the bell to the port marked as PC (placed under a small flap Fig. 2)

A ready-made cable or the cable made individually, in accordance with

the instructions available on th be

used.

e page canwww.kakadu.sealcom.pl,

TECHNICAL DATA

power supply - battery 6F22 9V (is it recommended

to use alkaline batteries)

power input when not switched on - 0 mA

switching on - through short-circuit or the supply-

ing of the voltage ~230V

weight (without battery) - 270 g

dimensions (diameter/height) - 167mm / 54 mm

power input when reproducing - maximum 350 mA

THE REMARKS CONCERNING INSTALLATION OF

THE BELL

1.If the bell is installed in the wiring of ~230V, the lighted door

push-buttons cannot be used.

2.Irrespective of the type of the wiring, to which the bell is

connected, the connection of the battery 9V is

required.

bell

This is caused by the fact that the current always flows through the

lighted buttons. This, in turn, is the reason that the anti-lock

protection is activated. A simple solution of this problem is

disconnection of the lighting (LED or neon) in the push-button.

always

3.The connection of the voltage of ~230V to the blue connector

(J3) results in irreversible damage of the bell.

warranty period

what is covered and what is not covered

who may enforce the warranty

how you can get warranty service

SEALCOM warrants this product against any defect in material and workmanship for 12 (twelve)

months from the date of purchase by the original retail purchaser.

Except as specified below, this warranty covers any defects in materials and workmanship of this

product. The following are not covered by the warranty:

1. Damage or deterioration of the casing.

2. Any unit that has been altered or on which the serial number has been defaced, modified, or

removed.

3. Damage, deterioration or malfunction resulting from:

a) accident, misuse, abuse or neglect;

b) failure to follow instructions supplied with the product;

c) repair or attempted repair by anyone not authorized by SEALCOM to repair this product;

d) causes other than product defects, including lack of technical skill, competence or experience of

the user. Especially damages which may arise of incidental use respectively by improper

ventilation.

This warranty may be enforced only by the original retail purchaser. This warranty will be granted only

when the original invoice or sales receipt (indicating the date of purchase, product type and dealer’s

name) is presented together with defective product.

1. If your unit needs service during the warranty period, please contact the local authorized distributor

for this product.

2. Please ensure to fill out the warranty certificate correctly. SEALCOM reserves the right to refuse the

guarantee service if the documents are missing or incomplete in the understanding of this terms.

These warranty terms do not affect any statutory rights of consumers which were granted by the

respective national laws.

WARRANTY

sealcom

SEALCOM s.c.

ul. Pomorska 26A

83-200 Starogard Gd., Poland

[email protected]

Date of purchase ................................

Serial number .....................................

Date of production ...............................

Dealer’s stamp and signature

Table des matières

Autres manuels Sealcom Accessoires

Sealcom

Sealcom KAKADU Manuel du propriétaire

Sealcom

Sealcom KAKADU Fiche technique

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur