Seafloor TriDrone Manuel de programmation

- TriDrone USV

- TriDrone Carry Case

- TriDrone Hardware Kit

- Data Collector Cable

- Accessory Pouch

-Spektrum Remote

Control with case

-USB Drive

-Mast

IMPORTANT

THANK YOU FOR PURCHASING SEAFLOOR SYSTEMS' PRODUCTS FOR YOUR SURVEYING NEEDS.

Please read through all of these Instructions and tips before proceeding with the operation. We do our best

to provide a simple setup process for all applications however please contact your nearest authorized

dealer if you encounter issues.

Always disconnect any power sources connected to your vessel before servicing vessel or accessories.

PRODUCT INCLUDES:

STEP: 1

Remove the vessel from the

case. Remove the remote case

from the top of the lid. Remove all

accessories from accessory pouch

located at the bottom of the case.

QUICKSTART INSTRUCTIONS

TriDrone Portable Remote Surveying Vessel

QUICKSTART INSTRUCTIONS

STEP: 2

Attach the thruster to the rear bracket of the vessel and secure by tightening

retaining screw.

STEP: 3

Insert fully charged 4S battery

and connect to power

distribution cable.

STEP: 4

Open bow hatch lid with provided hatch wrench,

and remove lid.

STEP: 5

Run the data collector cable through the inside of the hull through to the

hull hatch lid.

QUICKSTART INSTRUCTIONS

STEP: 6

Connect data collector cable to

transducer.

STEP: 8

Connect the thruster cable to the bulkhead

located at the stern of the vessel.

STEP: 7

Attach antenna to the mounting screw located at the front of the frame.

QUICKSTART INSTRUCTIONS

Operation: Be sure to observe and follow all local water safety regulations and procedures. Always

operate vessel within line of sight, and immediately stop operation if hazards or safety risks arise.

Your setup is now complete.

Welcome to the Seafloor Squad!

WARRANTY INFORMATION

For warranty information, visit https://www.seafloorsystems.com/terms-and-conditions 4415 Commodity Way, Shingle

Springs, CA, 95682 • 530-677-1019 https://www.seafloorsystems.com/

STEP: 9

Switch power to the "On" position.

STEP: 10

Connect the remote by holding the power button for

approximately 2 seconds. The remote will beep when

activated. You are now ready to survey.

Table des matières

Autres manuels Seafloor Équipement marin

Seafloor

Seafloor EchoBoat-240 Manuel utilisateur

Seafloor

Seafloor HydroCat 180 Manuel utilisateur

Seafloor

Seafloor AutoNav Manuel utilisateur

Seafloor

Seafloor EchoBoat 160 ASV Manuel utilisateur

Seafloor

Seafloor Sonarmite Manuel utilisateur

Seafloor

Seafloor AutoNav PLUS Manuel utilisateur

Seafloor

Seafloor HyDrone ASV Manuel utilisateur

Seafloor

Seafloor HydroLite-DFX Manuel utilisateur

Manuels Équipement marin populaires d'autres marques

Clarion

Clarion CMS2 Manuel de réparation

EBS

EBS M7000 Manuel utilisateur

Kongsberg

Kongsberg M3 Bathy Manuel utilisateur

NPK

NPK SCS-1002 Manuel utilisateur

Furuno

Furuno FE-800 Manuel utilisateur

Harken

Harken 1561 Manuel utilisateur

Simrad

Simrad DD15 Manuel utilisateur

Notifier

Notifier FS-BSO Manuel utilisateur

Raymarine

Raymarine ST40 Manuel utilisateur

E2S

E2S E2XS112UL Manuel utilisateur

R2Sonic

R2Sonic 2026 Manuel utilisateur

COBHAM

COBHAM SAILOR 6000 Manuel utilisateur

Clarion

Clarion GR10BT Manuel de réparation

Raymarine

Raymarine Maxiview ST80 Guide de l'utilisateur

GUIDANCE MARINE

GUIDANCE MARINE 20- Series Instructions de montage

Raymarine

Raymarine ST60 Tridata Guide de l'utilisateur

olympia electronics

olympia electronics ΒS-531/1/MAR Manuel utilisateur

Sonic

Sonic 2024 Manuel utilisateur