Scotts S1642, S1742, S2046 Manuel utilisateur

OMGX10784 C0

C0 Scotts Lawn Tractors

S1642, S1742, and S2046

OPERATOR’S MANUAL

North American Version

Litho in U.S.A.

Introduction

INTRODUCTION

Introduction

THANK YOU for purchasing a Scotts product.

Read this manual and your attachment manual thoroughly.

Failure to do so could result in personal injury or equipment

damage.

This manual should be considered a permanent part of

your machine and should remain with the machine when

you sell it.

Product warranty is provided as part of John Deere’s

support program for customers who operate and maintain

their equipment as described in this manual. The product

warranty is explained on the warranty certificate you

received from your dealer.

Measurements in this manual are metric units and their

U.S. customary equivalents. RIGHT-HAND and LEFT-

HAND sides are determined by facing in the direction the

machine will travel when going forward. When you see a

broken line arrow (------>), it indicates the part it is pointing

to is hidden.

CALIFORNIA Proposition 65 Warning

Warning:gThe Engine Exhaust from

this product contains chemicals known to the

State of California to cause cancer, birth

defects or other reproductive harm.

Product Identification

PRODUCT IDENTIFICATION

Product Identification

Record Identification Numbers

Scott’s Lawn Tractors

S1642, S1742, and S2046 PIN (020001 - )

If you need to contact an Authorized Service Center for

information on servicing, always provide the product model

and serial number.

You will need to locate the identification number for the

machine and for the engine. Record the information in the

spaces provided below.

PRODUCT IDENTIFICATION NUMBER (A), (under seat):

__ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __

ENGINE SERIAL NUMBER (B), (on fan shroud):

__ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __

DATE OF PURCHASE:

_________________________________________

DEALER NAME:

_________________________________________

DEALER PHONE:

_________________________________________

Model S1642

Model S1742 and S2046

Assembly - 0

ASSEMBLY

Assembly

Identify Parts

Connect and Check Battery

NOTE: Do not remove the BLACK negative (–)

protective cap at this time.

1. Remove and discard the RED positive (+) protective cap

from the positive (+) battery terminal.

2. Connect RED positive (+) cable (A) to battery with 6mm

hex head bolt and 6 mm flange nut. Tighten securely. Apply

petroleum jelly or silicone spray to terminal to prevent

corrosion. Install the red terminal cover.

3. Remove and discard the BLACK (–) protective cap from

the negative battery terminal.

4. Connect silver braided grounding cable (B) to the

negative (–) terminal (C) with remaining 6 mm hex head

bolt and 6 mm flange nut and tighten securely. Apply

petroleum jelly or silicone spray to terminal to prevent

corrosion.

42-Inch Mowers Only

•If tractor/mower deck is being set-up for mulching, install

mulch cover kit. (See Using Mower Deck Mulch Ready in

the Operating Mower section.)

•If tractor/mower deck is being set-up for side discharger

or 2-bag bagger DO NOT install mulch cover kit. (See

Using Mower Deck Side Discharge OR Using Mower Deck

with Optional Equipment in the Operating Mower section.)

A Operator’s Manual

B Safety Video

C Bag of Hardware

DKey

Bag of Hardware:

•2 - M8x16 Bolts - Battery

•2 - M8x16 Nuts - Battery

cCAUTION: Avoid injury! Prevent Battery

Explosions:

- Keep sparks, lighted matches, and open flame

away from the top of battery. Battery gas can

explode.

- Never check battery charge by placing a metal

object across the posts. Use a volt-meter or

hydrometer.

- Do not charge a frozen battery; it may

explode. Warm battery to 16°C (60°F)

IMPORTANT: Avoid damage! This battery comes

fully charged. If the mower is not used by the

Service Expiration Date indicated on the battery,

charge the battery. (See Charging the Battery in the

Service - Electrical section.)

cCAUTION: Avoid injury! DO NOT attempt to

open, add fluid or service battery. Any attempt

to do so will void warranty and lead to possible

injury.

cCAUTION: Avoid injury! Never operate the

mower without the discharge chute guard in

place.

Assembly - 1

ASSEMBLY

Checking Tire Pressure

1. Check tires for damage.

2. Check tire pressure with an accurate gauge.

3. Add or remove air, if necessary:

cCAUTION: Avoid injury! Explosive separation

of a tire and rim parts can cause serious injury

or death:

- Do not attempt to mount a tire without the

proper equipment and experience to perform

the job.

- Always maintain the correct tire pressure. Do

not inflate the tires above the recommended

pressure. Never weld or heat a wheel and tire

assembly. The heat can cause an increase in

air pressure resulting in a tire explosion.

Welding can structurally weaken or deform the

wheel.

- When inflating tires, use a clip-on chuck and

extension hose long enough to allow you to

stand to one side and NOT in front of or over

the tire assembly.

- Check tires for low pressure, cuts, bubbles,

damaged rims or missing lug bolts and nuts.

Tire Size Pressure-kPa (psi)

Front: 15-Inch 97 kPa (14 psi)

Rear: 20-Inch 69 kPa (10 psi)

Safety Signs - 2

SAFETY SIGNS

Safety Signs

Safety-Alert Symbol

Read and recognize safety information. Be alert to the

potential for personal injury when you see this safety-alert

symbol.

On your machine safety labels, the words DANGER,

WARNING, and CAUTION are used with this safety-alert

symbol. DANGER identifies the most serious hazards.

In this manual, the word CAUTION and this symbol call

attention to safety messages.

Machine Safety Labels

DANGER

AVOID SERIOUS INJURY OR DEATH

•Do not mow when children or others are around

•Do not mow in reverse

•Look down and behind before and while backing

•Never carry children even with blades off

WARNING

AVOID SERIOUS INJURY OR DEATH

•Drive up and down slopes, not across

•Avoid sudden turns

•If machine stops going uphill, stop blade and back down

slowly

•Keep safety devices (guards, shields, and switches) in

place and working

•Read operator’s manual

•When leaving machine:

–Stop engine

–Set park brake

–Remove key

DANGER/POISON

SHIELD EYES.

EXPLOSIVE GASES CAN CAUSE BLINDNESS OR

INJURY.

•SPARKS

•FLAMES

•SMOKING

SULFURIC ACID CAN CAUSE BLINDNESS OR SEVERE

BURNS

FLUSH EYES IMMEDIATELY WITH WATER.

GET MEDICAL HELP FAST.

MAINTENANCE-FREE

KEEP OUT OF THE REACH OF CHILDREN. DO NOT TIP.

DO NOT OPEN BATTERY!

Picture Note: Located on Battery under seat

DANGER

ROTATING BLADE

DO NOT PUT HANDS OR FEET UNDER OR INTO

M96445

Safety Signs - 3

SAFETY SIGNS

MOWER WHEN ENGINE IS RUNNING

THROWN OBJECTS

BEFORE MOWING, CLEAR AREA OF OBJECTS THAT

MAY BE THROWN BY BLADE

DO NOT OPERATE MOWER WITHOUT DISCHARGE

CHUTE OR ENTIRE GRASS CATCHER IN PLACE

Picture Note: Located on Right-Hand side of deck

DANGER

ROTATING BLADE

DO NOT PUT HANDS OR FEET UNDER OR INTO

MOWER WHEN ENGINE IS RUNNING

Picture Note: Located on Left-Hand side of deck

Emission Control System Certification Label

NOTE: Tampering with emission controls and

components by unauthorized personnel may result in

severe fines or penalties. Emission controls and

components can only be adjusted by EPA and/or CARB

authorized service centers. Contact your John Deere

Commercial and Consumer Equipment Retailer

concerning emission controls and component

questions.

The presence of an emissions label signifies that the

engine has been certified with the United States

Environmental Protection Agency (EPA) and/or California

Air Resources Board (CARB).

The emissions warranty applies only to those engines

marketed by John Deere that have been certified by the

EPA and/or CARB; and used in the United States and

Canada in off-road mobile equipment.

Emission Compliance Period

If your engine has the emission compliance category listed

on the emission control system certification or air index

label, this indicates the number of operating hours for which

the engine has been certified to meet EPA and/or CARB

emission requirements. The following table provides the

engine compliance period in hours associated with the

category found on the certification label.

Certification

Your mower has been certified by an independent

laboratory for compliance with American National Standard

B-71.1, “Safety Specifications”for Power Lawn Mowers,

Lawn and Garden Tractors, and Lawn Tractors.

M96445

Agency Category Hours

EPA C 250

EPA B 500

EPA A 1000

CARB Moderate 125

CARB Intermediate 250

CARB Extended 500

Controls - 4

CONTROLS

Controls

Tractor Controls - Gear

A - Throttle/Choke Control

B - Foot Pedal - Brake/Clutch

C - Reverse Implement Option Switch

D - Attachment Lift Lever

E - Locking Lever

F - Transmission Shift Lever

G - Park Brake

H - PTO Drive Lever

I - Ignition Switch

Tractor Controls - Automatic

A - Choke Knob (S2046)

B - Throttle/Choke Control (S1642 and S1742)

Throttle Control (S2046)

C - Foot Pedal - Brake/Clutch/Return to Neutral

D - Reverse Implement Option Switch

E - Attachment Lift Lever

F - Locking Lever

G - Free Wheeling Knob

H - Transmission Shift Lever (Hand Control Units

Only) Cruise Control Lever (Foot Control Units

Only)

I - Park Brake

J - Foot Pedal, Reverse (Foot Control Units Only)

K - Foot Pedal, Forward (Foot Control Units Only)

L - PTO Drive Lever

M - Ignition Switch

Operating Machine - 5

OPERATING MACHINE

Operating Machine

Operate Safely

•In addition to reading your Operator’s Manual, view your

Mowing Safety Video.

•Check brake action before you operate. Adjust or

service brakes as necessary.

•Inspect machine before you operate. Be sure hardware

is tight. Repair or replace damaged, badly worn, or missing

parts. Be sure guards and shields are in good condition

and fastened in place. Make any necessary adjustments

before you operate.

•Clear work area of objects that might be thrown. Keep

people and pets out of the work area. Stop machine if

anyone enters the area.

•If you hit an object, stop the machine and inspect it.

Make repairs before you operate. Keep machine and

attachments properly maintained and in good working

order.

•DO NOT leave machine unattended when it is running.

•Only operate during daylight or with good artificial light.

•Be careful of traffic when operating near or crossing

roadways.

•Do not wear radio or music headphones while operating

the machine. Safe operation requires your full attention.

•Older adults are involved in a large percentage of riding

mower accidents involving injury. These operators should

evaluate their ability to operate a mower safely enough to

protect the operator and others from serious injury.

Park Safely

•Stop machine on a level surface, not on a slope.

•Disengage mower blades.

•Lower attachments to the ground.

•Engage park brake.

•STOP engine.

•Remove key.

•Before you leave the operator’s seat, wait for engine and

all moving parts to STOP.

Rotating Blades are Dangerous - Protect

Children and Prevent Accidents

PROTECT CHILDREN:

•Never assume that children will remain where you last

saw them. Children are attracted to mowing activity, stay

alert to the presence of children.

•Keep children in the house when you are operating the

machine.

•Turn machine off if a child enters the mowing area.

•Use extra care when you come to blind corners, shrubs,

trees, or other objects that may block your vision.

•DO NOT let children or an untrained person operate the

machine.

•DO NOT carry or let children ride on machine or any

attachment even with the blades off. DO NOT tow children

in a cart or trailer.

HELP PREVENT SERIOUS OR FATAL ACCIDENTS:

•Be alert at all times, drive forward carefully. People

especially children can move quickly into the mowing area

before you know it.

•Back carefully. Disengage mower blades and look

behind the machine carefully, especially for children, before

you back up.

•DO NOT mow in reverse unless it is absolutely

necessary.

•Disengage mower blades when you are not mowing.

•DO NOT operate machine if you are under the influence

of drugs or alcohol.

Operating Machine - 6

OPERATING MACHINE

Avoid Tipping

•DO NOT drive where machine could slip or tip.

•Stay alert for holes and other hidden hazards in the

terrain.

•Keep away from drop-offs.

•Slow down before you make a sharp turn or operate on

a slope.

•When pulling loads or using heavy equipment, use only

approved hitches, limit loads to those you can safely

control, and use counterweights or wheel weights when

required per this manual or your attachment manual.

•Drive up and down a hill—not across. Be careful when

you change direction on a slope.

•DO NOT stop when going up hill or down hill. If machine

stops going up hill, DISENGAGE mower blades and back

down slowly.

•DO NOT mow wet grass. Reduced traction could cause

sliding.

•DO NOT try to stabilize the machine by putting your foot

on the ground.

Keep Riders Off

•Only allow the operator on the machine. Keep riders off.

•Riders on the machine or attachment may be struck by

foreign objects or thrown off the machine causing serious

injury.

•Riders obstruct the operator’s view resulting in the

machine being operated in an unsafe manner.

Wear Appropriate Clothing

•Wear close fitting clothing and safety equipment

appropriate for the job.

•Loud noise can cause impairment or loss of hearing,

wear a suitable protective device such as earplugs.

Transport Safely

•Use safety lights and devices. Slow moving machines

when driven on public roads are hard to see, especially at

night. Avoid personal injury or death resulting from a

collision with a vehicle.

•Whenever driving on public roads, use flashing warning

lights and turn signals according to local regulations. Extra

flashing warning lights may need to be installed.

Adjusting Seat

1. Pivot seat forward on its mounting bracket.

Autres manuels pour S1642, S1742, S2046

Table des matières

Autres manuels Scotts Tondeuse à gazon

Scotts

Scotts Bergman 320 9237 Manuel utilisateur

Scotts

Scotts 51519S Manuel utilisateur

Scotts

Scotts 907254 - LM21SW Manuel utilisateur

Scotts

Scotts 304-14S Manuel utilisateur

Scotts

Scotts 62016S Manuel utilisateur

Scotts

Scotts 60062S Manuel utilisateur

Scotts

Scotts Classic 20" 2000-20S Manuel utilisateur

Scotts

Scotts Turf Master C4013-050 Manuel utilisateur

Scotts

Scotts S2048, S2554 Manuel utilisateur

Scotts

Scotts 415-16S Manuel utilisateur

Scotts

Scotts 415-16s Manuel utilisateur

Scotts

Scotts 2000-20S Manuel utilisateur

Scotts

Scotts SP6211 Manuel utilisateur

Scotts

Scotts S2546 Manuel utilisateur

Scotts

Scotts S2348 Manuel utilisateur

Scotts

Scotts 304-14S Manuel utilisateur

Scotts

Scotts 62162S Manuel utilisateur

Scotts

Scotts 60362S Manuel utilisateur

Scotts

Scotts 2010-20sg Manuel utilisateur

Scotts

Scotts S1642, S1742, S2046 Manuel utilisateur

Scotts

Scotts 2020-16S Manuel utilisateur

Scotts

Scotts 62014S Manuel utilisateur

Scotts

Scotts 60040S Manuel utilisateur

Scotts

Scotts 61940S Manuel utilisateur

Manuels Tondeuse à gazon populaires d'autres marques

RHINO

RHINO 1958 Manuel utilisateur

Wolf Garten

Wolf Garten Compact plus 40 B Manuel utilisateur

Cub Cadet

Cub Cadet LTX 1045 Manuel utilisateur

Craftsman

Craftsman 917.378461 Manuel utilisateur

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manuel utilisateur

Challenge

Challenge CH18V2 Instructions de fonctionnement

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manuel utilisateur

DEWEZE

DEWEZE ATM-725 Manuel d'utilisation

Weed Eater

Weed Eater 180083 Manuel utilisateur

Husqvarna

Husqvarna Poulan Pro PP185A42 Manuel utilisateur

Better Outdoor Products

Better Outdoor Products Quick Series Manuel utilisateur

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manuel d'utilisation

MTD

MTD 795, 792, 791, 790 Manuel utilisateur

Toro

Toro Groundsmaster 3505-D Manuel utilisateur

Dennis

Dennis FT 610 Manuel utilisateur

AIRFORCE

AIRFORCE F-15 Gen 3 Manuel utilisateur

MTD

MTD 126-220-000 Manuel utilisateur

Toro

Toro 74806 Manuel utilisateur