Scorpio SR-i500 Mode d’emploi

SR-i500

FM 2-Way Security System

INSTALLATION MANUAL

AND USER’S GUIDE

Standard Features

•½ mile 2-Way FM Transceiver

•Remote sensor control

•LCD Water proof / impact

resistant remote

•Battery safeguard with “sleep

mode”

•Ultra low power drain MCM

•Violation display with time stamp

•Built-in accelerometer

•Passive arming

•Ignition protection

•Selectable arming / disarming

•Range Confirmation Signal (RCS)

•Programmable multi-tone siren

•Remote panic feature

Optional Accessories

•Perimeter sensor (SN-5) – A miniature multi stage microwave sensor that detects motion

in mass around the motorcycle.

•Ignition disable and anti-hijack kit (RID-5) - Allows remote disabling of the motorcycle’s

electrical system, should someone force you off your bike. Also prevents the engine from

being started when the system is armed.

•Back-up battery (BAT-5) – A built-in back-up battery feature allowing the siren and

transmitter to continue operating when power is interrupted.

•Factory Connector Kits–OEM style connectors that simply plug into the motorcycle’s

factory wiring harness. Connector kits are available for select motorcycle models.

Table of Contents

Installation

•Component List ---------------------------------------------------------------- Page 2

•Planning The Installation ---------------------------------------------------- Page 2

•Mounting The Components ----------------------------------------------- Page 3

•Color Codes --------------------------------------------------------------------- Page 3

•Connections --------------------------------------------------------------------- Page 4

•Using the T-tap Connectors ------------------------------------------------ Page 4

User’s Guide

•Remote Transceiver Icons and Message Display ------------------- Page 5

•Turning Transceiver On / Off ----------------------------------------------- Page 5

•RCS (Range Conformation Signal) -------------------------------------- Page 6

•Transceiver Battery Status --------------------------------------------------- Page 6

•Operating Instructions ----- -------------------------------------------------- Page 6

•Alarm Triggers-------------------------------------------------------------------- Page 7

•Sensor Memory Display ------------------------------------------------------ Page 7

•Battery Safeguard with “Sleep Mode” -------------------------------- Page 7

•Motorcycle Battery Status -------------------------------------------------- Page 8

•Locking the Transceiver’s buttons --------------------------------------- Page 8

•Checking Motorcycle Status and Violation Display --------------- Page 8

•Programming and customizing Instructions -------------------------- Page 9

•Selecting Transceiver Alert Type ------------------------------------------ Page 9

•Selecting Auto / Manual Arming ----------------------------------------- Page 10

•Selecting Siren Tone and Alarm Duration ----------------------------- Page 10

•Adjusting the Accelerometer (Shock / Tilt ) Sensor ---------------- Page 10

•Setting Clock Time ------------------------------------------------------------ Page 11

•Setting Alarm Clock ---------------------------------------------------------- Page 11

•Encoding a Transceiver ------------------------------------------------------ Page 11

Optional Accessories Instructions

•Perimeter Sensor (SN-5) ------------------------------------------------------ Page 12

•Ignition Disable / Anti-hijack Unit ----------------------------------------- Page 13

•Back-up Battery ---------------------------------------------------------------- Page 14

Warranty and FCC Information

•Limited Warranty ------------------------------------------------------------- Page 15

•FCC Notice ---------------------------------------------------------------------- Page 15

•Contact information --------------------------------------------------------- Page 15

Installation

Components List

MCM (Main Control Module)

Remote Transceiver

Accessory Harness

Generic Installation Kit (GEN-1)

Main Harness (HAR-1)

Planning the Installation

It is very important that before starting the installation of the security system, you carefully read

the installation instructions and spend time planning the installation. By planning ahead you will

be able to select the best approach in placing, securing and wiring the system to your specific

motorcycle. Although the installation is not difficult, there are a number of steps that must be

taken for the system to operate properly. We suggest the following steps:

1. Check that your motorcycle battery is fully charged and that all electrical circuits are in

good working condition.

2. Check the layout and construction of the motorcycle to decide what space is available to

place the components.

3. Verify that no moving parts interfere with the components or their wires.

4. Do not route wires near sharp edges, which could cut wires and cause a short.

5. Do not mount components near extreme heat areas such as exhaust pipes etc.

6. Allow at least an inch or two of slack at all connection points to reduce the chance that a

connection will break apart due to vibration.

Mounting the Components

Select a suitable location under the seat or in a side cover. Mount the MCM using Velcro or

cable ties. Make sure that it is not exposed or easily reached.

Routing the Antenna Wire

The MCM includes an 18” antenna wire. The first 12” is a coaxial wire; the remaining 6” is the

reception antenna wire. When routing, try to avoid running the antenna along or near metal. For

best performance, have the antenna wire as vertical as possible and exposed.

Wire Connections

Note: All connectors are unique and will only fit the appropriate component one way.

The MCM is equipped with two connectors. One is for the main harness (HAR-1) and the other is

for the optional accessories.

Accessory Harness

Plug in the accessory harness to the matching connector on the MCM. If no options are being

used, plug in the supplied dust cover.

Main Harness

Note: If the optional factory connector kit is being used, please disregard this section of the

instructions and refer to the instructions supplied with the factory connector kit.

The main harness consists of two harnesses. One is labeled (HAR-1) and the second is labeled

(GEN-1). Plug in the white 4 pin connector from the (HAR-1) into the matching 4 pin connector

from the (GEN-1). The (HAR-1) also has a waterproof connector that plugs into the MCM. The

wires should be connected as follows:

HAR-1

Black wire with fuse and ring terminal – To battery Positive (+).

GEN-1

Black wire – To ground (-).

Grey wire – To turn signal power wire (Left).

Grey wire – To turn signal power wire (Right).

Orange wire – To tail light wire or any other wire that is hot (+) when ignition is “ON” (NOTE: this is

an input to the alarm this connection is not designed to flash the tail light).

Color Codes:

Ground (-) Tail Light Left Turn Signal Right Turn Signal

Honda Green wire Brown wire Orange wire Blue wire

Kawasaki Black wire Red wire Green wire Grey wire

Suzuki Black/White Brown wire Green or Black Grey wire

Yamaha Black wire Blue wire Green wire Brown wire

Harley Davidson Black wire Blue wire Brown wire Purple wire

Connections

Fuse

To Battery (+)

Accessory

HAR-1 Connector

GEN-1

MCM

Black – To Ground (-)

Grey – To Turn Signal

Orange – To Tail Light

Note: Connect the (HAR-1) harness to the MCM only after installation is completed. If the

battery is to be removed, disconnect this connector first. Reconnect only after battery

terminals are reconnected.

Note: When the main harness (HAR-1) is plugged in, the siren should chirp. If the siren dose

not chirp; check the fuse, and battery (+) and ground (-) connections.

Using the T-tap Connectors

1) Place female T-tap connector over wire to be tapped, close and squeeze until it snaps close.

2) Now slip male T-tap connector over hinged end of the female connector to make a

connection.

Motorcycle Wire

Female T-tap

2) Female T-tap

Male T-tap

Motorcycle

Wire

Wire from (GEN-1)

User’s Guide

Remote Transceiver Icons and Message Displays

3. Press button 4

repeatedly to

scroll though the

programmable

icons

Battery Level Indicator

System Armed

Silent Paging Only Arming

Shock Trigger

Perimeter Trigger

Alarm Clock

Ignition Trigger

Clock

Back up Power Activated

Signal Indicator

Alert Type Aud/Vibr

System Disarmed

Tilt Trigger

Button #1 Button #2

Button #3

Button # 4

Cycle Low Battery Indicator

Turning the Transceiver On/Off

•To turn “on” , press and hold button #4 until the transceiver chips two times. The power is

now “on”.

•To turn “off”, press and hold button #4 until the transceiver chips two time followed by

another two times. The power is now “Off”.

Note: When the Transceiver is in the “Off” mode only the and icons will still be

displayed

Note: Out of the box the transceiver does not have the battery installed, please install battery to

operate transceiver.

RCS (Range Confirmation Signal)

If the system is armed and the Transceiver is within range of the MCM the LCD displays icon

If the Transceiver does not receive the RCS signal the icon will not appear.

Transceiver Battery Status

The LCD will display 3 different icons to show the Transceiver battery status.

Operating Instructions

The following instruction assumes that the transceiver is with in range of the motorcycle.

Arm

1. Press button #1, siren chirps 3 times and the turn signal lights flash 1 time.

2. The Transceiver echoes 3 chirps and the LCD displays and and PERIMT OFF icons.

Disarm

1. Press button #2, siren chirps 1 time and lights flash 1 time.

2. The Transceiver echoes 1 chirp and the LCD displays icon.

Arming With Optional Perimeter Sensor

1. Press button #3, siren chirps 4 times and turn signal lights flash 1 time.

2. The Transceiver echoes 4 chirps and the LCD displays , icons.

3. The system is armed and the Perimeter Sensor is activated.

Arming Without Siren / Paging Only

1. Press buttons #1 and #3 at the same time, siren chirps 5 times and the turn signal lights

flash 1 time.

2. The Transceiver echoes 5 chirps and the LCD displays , and icons.

3. The system is armed but the siren and turn signal lights are disabled for a silent paging

only alert.

Arming Without Siren or Perimeter Sensor (optional) / Paging Only

1. Press buttons #2 and #3 at the same time, siren chirps 6 times and the turn signal lights

flash 1 time.

2. The Transceiver echoes 6 chirps and the LCD displays , ,and PERIMT OFF icons.

3. The system is armed but the siren, turn signal lights and perimeter sensor are disabled.

Panic/ Stop Trigger

a. When system is armed press button #3 for Panic feature. (panic feature will

sound siren for a few seconds, drawing attention to your bike)

b. Pressing button #3 during an alarm trigger stops the alarm cycle but keeps

the system armed.

Alarm Triggers

When the system is triggered, the siren will sound and the turn signal lights will flash. The

Transceiver’s LCD will display the following messages:

1. If bike is bumped, the LCD will display icon. The siren on the bike will sound for 5

seconds and the lights will flash. This cycle will repeat twice.

2. If the perimeter sensor triggers a full alarm cycle, the LCD will display icon. The siren

on the bike will sound for 5 seconds. This cycle will repeat twice

(Note: The turn signal lights will not flash for a perimeter sensor trigger).

3. If the bike is tilted, the LCD will display icon. The siren on the bike will sound for 30

seconds and the lights will flash. This cycle will repeat six times.

4. If the ignition switch is turned on or tampered with, the LCD will display Icon. The

siren on the bike will sound for 30 seconds and the lights will flash. This cycle will repeat

six times.

5. With the optional back up system installed, the LCD will display icon if the main

harness or battery power supply is disconnected. The MCM will still continue to sound

and transmit from its internal power source. The siren on the bike will sound for 30

seconds. This cycle will repeat six times.

6. The Transceiver will continue to flash the triggered icon until any button is pressed.

Note: The Transceiver will sound a unique tone to correspond with the triggered sensor

Sensor Memory Display

When the system is disarmed the turn signals will flash to indicate if there has been an alarm

trigger. The lights will flash once to indicate that the system has been disarmed, additional flashes

indicate that the following trigger has occurred:

1 flash then 1 additional flash = Shock Trigger

1 flash then 2 additional flashes = Tilt Trigger

1 flash then 3 additional flashes = Perimeter Sensor Trigger

1 flash then 5 additional flashes = Ignition Trigger

Motorcycle Battery Safeguard with “sleep mode”

•If the optional perimeter sensor is being used and the alarm is armed for more then 10 days

the system will automatically disable the perimeter sensor.

•If the alarm is armed for more than 30 days, the system will automatically disable the systems

receiver. In this mode the transceiver will no longer be able to operate the system but the

system is still armed and protecting the bike.

•To disarm, trigger the alarm, and press the #2 button.

Motorcycle Battery Status

When the voltage on the motorcycle battery drops below 11.2 volts The LCD displays icon.

Locking the Transceiver’s buttons

To “lock”, press button #4 for 2 sec. The Transceiver will beep and buttons will lock.

To “unlock”, press button #4 for 2 sec. The Transceiver will beep and buttons will unlock.

Checking Motorcycle Status and Violation Display with Time Stamp

1. Press button #4. The back light and the memory screen will be displayed. If the alarm

was not triggered, all the sensor icons will come on and the # 0 0 will be displayed.

2. If there was an alarm trigger, the last triggered sensor will flash. Press button #4

repeatedly to scroll through all the triggered sensors in the Transceiver’s memory.

3. The alternating numeric display shows the current trigger, numbering of triggers in

memory, and the time the trigger occurred. For Example: [03 05] + [A 8:55] means

the tilt sensor was triggered. It was the 3rd sensor violated out of a total of 5 alarm triggers

and the event occurred at 8:55am.

4. Press button #3 to exit.

5. To clear memory, press and hold down button #3 for 2 seconds.

If no alarm triggers in memory, all

sensor icons will be displayed If the system was trigged, the last triggered

sensor will be displayed

Press button

4 once

Time of trigger

Trigger # Total # of triggers

Press button 4 repeatedly to

scroll though the trigger memory Pres button 3 to exit and clear.

Or, press and hold button 3 for 2

seconds to erase memory.

Programming and Customizing Instructions

There are two types of programming mode:

1) Programming the Transceiver- To program the transceiver the MCM does not have to be

installed or be within range. The programmable modes for the Transceiver are:

•Transceiver Alert Type (Audible/Silent Vibrate).

•Alarm Clock.

•Clock.

2) Programming the MCM- To program the MCM the system must be installed, with in range, and

in the disarmed mode. The programmable modes for the MCM are:

•Auto/Manual Arming.

•Siren Tones and Siren Duration.

•Adjusting Accelerometer (impact/shock sensor).

Entering Programming Mode

Follow the steps below to enter the programming mode:

3. Press button 4 repeatedly to

scroll though the programmable

icons

NOTE:

Press button 3 to

exit without

changing the

setting or saving

4. Press button 1 to

select icon and to begin

programming

1. Press button 4 twice to

enter programming

mode

2. Available programmable

options will be displayed.

The selected icon will flash

4. Press button 1 to

select icon and to begin

programming

1. Press Button 2

to scroll

between the

alert options

Alert options include: alert off, vibrate,

audible, vibrate and audible

Selecting Transceiver Alert Type (Audible/Silent/Vibrate)

1. Enter programming mode. The icon will begin to flash, press button #1 to select.

The LCD will display the current settings. To program follow these steps:

Note. At any time during programming press button # 3 to exit without saving and return to the

main screen

2. Press button

4 to save and

exit

Autres manuels pour SR-i500

Table des matières

Autres manuels Scorpio Alarme de voiture

Scorpio

Scorpio OEM-500i Mode d’emploi

Scorpio

Scorpio SR-i900 Series Manuel utilisateur

Scorpio

Scorpio CYL-300DX Mode d’emploi

Scorpio

Scorpio SR-i500 Manuel utilisateur

Scorpio

Scorpio SR-i500SW Mode d’emploi

Manuels Alarme de voiture populaires d'autres marques

Clifford

Clifford 3606X Manuel utilisateur

Ultra Start

Ultra Start 2500M SERIES Manuel utilisateur

Ultra Start

Ultra Start 650 Series Manuel utilisateur

Audiovox

Audiovox Prestige Platinum+ APS-511C Manuel utilisateur

Sparkrite

Sparkrite SRA8 Manuel utilisateur

Viper

Viper 4708V Manuel utilisateur

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Manuel

Falcon

Falcon Predator XL3 Guide de l'utilisateur

Audiovox

Audiovox Auto Security XR91 Mode d'emploi

Clifford

Clifford Sabre II Manuel utilisateur

CrimeStopper

CrimeStopper CS-8717 Guide de démarrage rapide

Ultra Start

Ultra Start 450 SERIES Manuel utilisateur

Scytek electronic

Scytek electronic Vectra X3 Manuel utilisateur

Excalibur

Excalibur AL-1860-EDPB Manuel utilisateur

Clifford

Clifford CYBER 2 Manuel utilisateur

Gemini

Gemini 7057 Manuel utilisateur

FlashLogic

FlashLogic FLRSBA PRESTIGE Manuel utilisateur

Magicar

Magicar FAI-440 Manuel utilisateur