SciCan Statim 2000 Guide d'installation
Statim 2000 & 5000
Technical
Training Manual
2
Table of Contents
Statim 2000 & 5000 Specifications 3
2000 Keypad 4
5000 Keypad, Installation & Language Selection 5
Display 6
Statim 2000 Unwrapped Cycle Description 7
Statim 2000 Wrapped Cycle Description 8
Statim 5000 Unwrapped Cycle Description 9
Statim 5000 Wrapped Cycle Description 10
Cassette Operation, Care & Maintenance, Seal Replacement 11
Statim 2000 & 5000 Cover Removal 12
SteamFlowChart 13
Sequence of Operation 14
No Power PCB Revision 2.4-2.92 & 6.4 15
Pump, Solenoid & Compressor Testing 16
Pump Filter Cleaning Instructions 17
ThermalFuseLocation 18
ProbeBracket 19
MicroswitchLocation 20
SolenoidValve 21
Boiler Calibration 2000 & 5000 Rev. 2.4-2.9 22
Boiler Calibration 2000 & 5000 Rev. 6.x & Adapter Boards with 44-pin Microprocessor 23
WaterTesters 24
Water Quality Problems 25
Water Quality Check Revision 4XX or 5XX Software 26
Control Box Connections 27
Water Pump Filters Tech Service Bulletin 28
QA Supply Water Tester 29
3
Statim 2000 & 5000 Specifications
The Statim 2000 & 5000 are tabletop steam sterilizers, which are designed to sterilize instruments and
handpieces between patients.
Statim 2000 Statim 5000
External Size (LgthxWdthxHgth) External Size (LgthxWdthxHgth)
17 3/4" x 16 1/4" x 6" 21 3/4" x 16 1/4" x 7 1/2"
Cassette Internal Dimensions Cassette Internal Dimensions
11" x 7" x 1 1/2" 15" x 7" x 3"
Reservoir Capacity Reservoir Capacity
4 Liters 4 Liters
Approximately 40 Cycles Approximately 15-18 Cycles
Weight Without Water Weight Without Water
46 Pounds 72 Pounds
Power Consumption Power Consumption
1300 Watts 1300 Watts
Printer Printer
Not Available Type: Thermal Paper
Print: 20 Characters Per Line
Speed: 1 Line Per Second
Capacity: 80 Cycles Per Roll
Cycle Time Cycle Time
Unwrapped: 6 Minutes* Unwrapped: 9 Minutes*
Wrapped: 12-15 Minutes* Wrapped: 15-18 Minutes*
Rubber & Plastics: 20 Minutes* Rubber & Plastics: 40 Minutes*
Heavy Duty Unwrapped: 12 Minutes*
Warranty Warranty
1 Year Parts (Excluding Seal) 1 Year Parts (Excluding Seal)
1 Year SciCan Labor 1 Year SciCan Labor
*Cycle times will vary depending on load size in cassette.
4
2000 Keypad
Cycle Sterilization Time & Temperature
1 Unwrapped Instruments 3.5 Minutes 135°C
2 Wrapped Instruments 10 Minutes 135°C
3 Rubber & Plastics 15 Minutes 121°C
4 Air Dry Only 60 Minutes
5 Start
6 Stop
1
2
3
4
5
6
5
5000 Keypad, Installation & Language Selection
Cycle Sterilization Time & Temperature
1 Unwrapped Instruments 3.5 Minutes 132°C
2 Wrapped Instruments 6 Minutes 132°C
3 Rubber & Plastics 20 Minutes 121°C
4 Heavy Duty Unwrapped 6 Minutes 132°C
5 Start
6 Stop
Installation
Adjust the bubble level, located in the right front corner of the Statim, so the bubble is in the 4 or
5 o’clock position.
The waste bottle should be placed below the Statim.
Install the exhaust tubing as short as possible with no complete loops and no dips below the
waste bottle.
Make sure the mesh rack in the cassette, is positioned so there is a gap underneath for airflow.
Cassettes need to be treated with Stat-Dri Plus when water begins to cling to the cassette lid.
Do not stack bags in the cassette.
All the above will help to enhance drying in the Statim cassette.
Selecting a Language
Turn the Statim OFF.
Hold down the wrapped instrument button and turn the Statim ON. Release the wrapped button
when the display appears.
Press and release the wrapped button or the unwrapped button to scroll through the languages.
You are looking for N A English (North American English).
When N A English appears on the display press the stop button.
1
2
3
4
5
6
6
Display
When the Statim is turned ON the display will show Statim and model 2000 or 5000 then the
software number. The last three digits of the software number (501) are the software revision.
The revision number is required to answer numerous questions concerning the Statim. The
display will change to Select A Cycle after approximately 5 seconds. To see the software
revision number again the Statim will need to be turned OFF and then back ON. This display is
for a Statim 2000, with revision 501 software.
Units manufactured from 1990 thru 1994 may say Select A Program with no software number
when turned ON.
When using the Troubleshooting Guide there are three sets of error codes.
Statims that say “Select A Program” when turned ON, use original Statim error codes on page 17
in the troubleshooting guide.
Statims with software revision 2XX when turned ON, use 2XX error codes page 3 in the
troubleshooting guide.
Statims with software revision 5XX when turned ON, use 5XX error codes page 10 in the
troubleshooting guide.
For units with revision 4XX software most troubleshooting will be done using 2XX codes.
Statim 2000 S201R501
Select A Cycle
7
Statim 2000 Unwrapped Cycle
Temperature rises to approx 102°C. Solenoid closes (new units 30 second delay after reaching
102°C before Solenoid closes). Unit then pressurizes to 135°C. Unit goes into sterilization for
3.5 minutes. Unit then depressurizes to 103°C, air-drying starts (on units with 4XX and 5XX
software the air compressor will turn ON while unit is still venting). This feature is to prevent
deposits from collecting in the boiler. The compressor turning ON during venting will remove
moisture from the boiler. The operator is unable to remove the cassette from the Statim until the
Stop button is pressed.
8
Statim 2000 Wrapped Cycle
Temperature rises to approx 102°C. Solenoid closes (new units 30 second delay after reaching
102°C before Solenoid closes). Unit then conditions to 135°C. Unit will hold at 135°C for
approximately 30 seconds, then the Solenoid opens and the unit depressurizes to 115°C. This
depressurization is to remove air from the bags. The Solenoid then closes and the unit
pressurizes to 135°C. The unit goes into sterilization for 10 minutes. Unit then depressurizes to
103°C and air-drying starts (on units with 4XX and 5XX software the air compressor will turn
ON while unit is still venting). This feature is to prevent deposits from collecting in the boiler.
The compressor turning ON during venting will remove moisture from the boiler. The operator
is unable to remove the cassette from the Statim until the Stop button is pressed.
9
Statim 5000 Unwrapped Cycle
Temperature rises to approx 102°C. Solenoid closes (new units 30 second delay after reaching
102°C before Solenoid closes). Unit then conditions to 132°C. The Solenoid opens and the unit
depressurizes to 115°C. This depressurization is to remove air from the large chamber. The
Solenoid then closes and the unit pressurizes to 132°C. The unit goes into sterilization for 3.5
minutes. Unit then depressurizes to 103°C and air-drying starts (on units with 4XX and 5XX
software the air compressor will turn ON while unit is still venting). This feature is to prevent
deposits from collecting in the boiler. The compressor turning ON during venting will remove
moisture from the boiler. The operator is unable to remove the cassette from the Statim until
the Stop button is pressed.
Note: Heavy Duty Unwrapped Cycle operates the same as the Unwrapped Cycle with a six-
minute sterilization time.
132ºC
(270ºC)
10
Statim 5000 Wrapped Cycle
Temperature rises to approx 102°C. Solenoid closes (new units 30 second delay after reaching
102°C before Solenoid closes). Unit then conditions to 132°C. The Solenoid opens and the unit
depressurizes to 115°C. The unit will condition up and down between 115°C and 132°C six
times. This depressurization is to remove air from the cassette and bags. The Solenoid then
closes and the unit pressurizes to 132°C. The unit goes into sterilization for 6 minutes. Unit
then depressurizes to 103°C and air-drying starts (on units with 4XX and 5XX software the air
compressor will turn ON while unit is still venting). This feature is to prevent deposits from
collecting in the boiler. The compressor turning ON during venting will remove moisture from
the boiler. The operator is unable to remove the cassette from the Statim until the Stop button
is pressed.
132ºC
(270ºC)
Autres manuels pour Statim 2000
6
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels SciCan Équipement de laboratoire
SciCan
SciCan STATIM 5000S Manuel utilisateur
SciCan
SciCan STATIM 7000 Guide d'installation
SciCan
SciCan SALUS Manuel utilisateur
SciCan
SciCan STATIM 900J Manuel utilisateur
SciCan
SciCan HYDRIM C61w G4 Manuel utilisateur
SciCan
SciCan statim 2000 G4 Manuel utilisateur
SciCan
SciCan statim 5000 G4 Mode d’emploi
SciCan
SciCan STATIM 7000 Manuel utilisateur
SciCan
SciCan Quantim 16 Manuel utilisateur
SciCan
SciCan statim 2000 G4 Manuel utilisateur
SciCan
SciCan QUANTIM B Manuel utilisateur
SciCan
SciCan statim 5000 G4 Manuel utilisateur
SciCan
SciCan STATIM Manuel utilisateur
SciCan
SciCan Bravo Manuel utilisateur
SciCan
SciCan HYDRIM L110w G4 Manuel utilisateur
SciCan
SciCan STATCLAVE G4 Manuel utilisateur
SciCan
SciCan HYDRIM C61w G4 Manuel utilisateur
SciCan
SciCan Statim 2000 Guide d'installation
SciCan
SciCan HYDRIM L110w Manuel utilisateur
SciCan
SciCan STATCLAVE G4 Manuel utilisateur
Manuels Équipement de laboratoire populaires d'autres marques
Agilent Technologies
Agilent Technologies 5800 ICP-OES Manuel utilisateur
Endress+Hauser
Endress+Hauser Cleanfit CPA875 Manuel utilisateur
NI
NI PXI-5422 Manuel
Collomix
Collomix Aqix Manuel utilisateur
SPEX SamplePrep
SPEX SamplePrep 6875 Freezer/Mill Series Manuel utilisateur
Ocean Insight
Ocean Insight FLAME-NIR+ Manuel utilisateur
