Schlumberger Reflex USB Manuel utilisateur

Reflex USB

Reader Installation Guide

Title Page

Copyrights and Trademarks

ii Reflex USB Reader Installation Guide

Trademarks

Schlumberger, Cryptoflex, Cyberflex, Cyberflex Access, and e-gate are

trademarks or registered trademarks of Schlumberger.

Microsoft, Windows, and Windows NT are registered trademarks of Microsoft

Corporation. Other company, product, and service names may be trademarks

or service marks of others.

You will find the Reader Driver License Agreement (License.txt) in the

following directory: \Program Files\Schlumberger\Smart Cards and

Terminals\Smart Card Readers\Reflex USB\Docs.

The Reader Driver License Agreement is also available from the Reflex Reader

Technical Support website: http://www.reflexreaders.com/Support/

support.html

Your feedback about this manual is welcome! Comments, questions, and

suggestions about any part of the Cyberflex® Access™ documentation library

can be posted to the Docs & Samples Conference of the User Discussion

Forums:

www.flexforum.com/cgi-bin/dcforum/dcboard.cgi

Document Date

C300477_rev2 November 2003

iii

Contents

1Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

2Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Installation Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Unsigned Driver Warning Messages . . . . . . . . . . . . . . . . . . . . . 4

Installing on Windows 98 or Windows Me . . . . . . . . . . . . . . . . . . . 5

Updating on Windows 98 or Windows Me . . . . . . . . . . . . . . . . 6

Installing or Updating on Windows 2000 or Windows XP. . . . . . . 8

3Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Table of Contents

Introduction

The SchlumbergerSema Reflex USB

smart card reader is designed to

install easily and quickly into an

existing PC network infrastructure.

The Reflex USB smart card reader

supports the Cyberflex Access

software environment and takes full

advantage of the smart card handling capabilities integrated in Microsoft

Windows operating systems (the Personal Computer/Smart Card, or PC/SC,

architecture).

The Reflex USB smart card reader uses the computer’s Universal Serial Bus

(USB) port to transfer data at rates up to 115,200 bps. This high data transfer

rate makes the Reflex USB smart card reader ideal for e-commerce and PKI

applications that require smart cards to store certificates, generate digital

signatures, and perform advanced encryption.

The Reflex USB smart card reader is Plug-and-Play-compliant on Windows 98

and Windows Me systems, and hot pluggable on Windows 2000 and

Windows XP systems. The reader uses the USB interface both to transfer data

and supply power, so you have only one cable to connect.

Operating Systems Supported

•Microsoft Windows 98 (Second Edition)

•Windows Me

•Windows 2000 (Service Pack 2)

•Windows XP Professional

NOTE The Reflex USB smart card reader has been discontinued. Drivers for the

Reflex USB were last verified on the platforms listed above, and are

currently available from the Reflex Reader Technical Support website

(www.reflexreaders.com/Support/Downloads/downloads.html) on an “as is”

basis. See the "End of Life Product Announcements" section in the Release

Notes for details.

Chapter 1 - Introduction

2Reflex USB Reader Installation Guide

Other System Requirements

•Port — Universal Serial Bus 1.1 or later

Cards Supported

The Reflex USB smart card reader works with all leading ISO 7816-compatible

microprocessor cards, including:

•Cryptographic cards

•Java cards

•Subscriber Identity Modules (SIMs)

•SchlumbergerSema e-gate™ cards

Product Specifications and Features

•Smart Card Connector — Friction contacts with ISO-compliant chip position;

Association Française de Normalisation (AFNOR) chip position not

supported.

•Card Power — Compliant with ISO 7816 and EMV — 5V; reader: 39 mA;

smart card: ≤60 mA (limited by ISO specification).

•Connection — Reader’s 2-meter cable connects to a Type A USB port.

Reader automatically detects card insertion and removal.

•Communication protocols — T=0 (asynchronous, half-duplex, byte-oriented)

and T=1 (asynchronous, half-duplex, block-oriented)

•Communication speed — Variable communication rate of up to 115,200 bps,

which you can control through Protocol Parameter Selection commands.

•Dimensions — 85mm x 68mm x 15mm (3.75" x 2.75" x .68")

•Color — Steel gray

Standards Compliance

•ISO/IEC 7816, parts 1–4

•EMV Level 1

•FCC and CE

•Microsoft PC/SC

Installation

This section contains instructions for

installing the SchlumbergerSema

Reflex USB smart card reader. The

computer must have an available USB

port.

Installation Notes

The table presents the following information about installing the Reflex USB

smart card reader on each supported operating system:

•Overview of the installation sequence on each operating system. For

detailed instructions, see the sections that follow.

•Summary of each operating system’s Plug-and-Play or hot pluggable

capability.

•Summary of the expected behavior of the Reflex USB smart card reader’s

power light on each operating system.

Chapter 2 - Installation

4Reflex USB Reader Installation Guide

Unsigned Driver Warning Messages

A driver is “unsigned” if certification of the driver by Microsoft was pending

but not yet complete at the time of release. Depending on driver signing

options established by local system security policy (Control Panel > System

Properties > Hardware > Driver Signing…), driver installation on Windows

2000, Windows XP, and Windows Server 2003 might either silently allow,

display a warning message, or block the installation of unsigned drivers. If a

warning message is displayed, click Ye s or Continue Anyway to complete

the driver installation.

Operating System Installation Notes

Windows 98 /

Windows Me

• Installation sequence: Install the Reflex USB smart card reader

software and the Microsoft Smart Card Base Components (if

they are not already installed), connect the Reflex USB smart

card reader, and reboot.

• Plug-and-Play compliant: Operating system detects Reflex USB

smart card reader at connect/disconnect; Smart Card Resource

Manager detects Reflex USB smart card reader at boot-time

(mid-session connect/disconnect detected only at reboot).

• Power light: Reflex USB power light is on continuously when the

reader is connected to the computer via a USB port (power light

blinks continuously when a card is fully inserted into the Reflex

USB smart card reader).

Windows 2000 /

Windows XP

• Installation sequence: Attach the Reflex USB smart card reader,

and then install the Reflex USB smart card reader software.

• Hot pluggable: Operating system and Smart Card Resource

Manager automatically detect Reflex USB smart card reader

status at connect/disconnect.

• Power light: Reflex USB power light is on continuously when the

reader is connected to the computer via a USB port (power light

blinks continuously when a card is fully inserted into the Reflex

USB smart card reader).

Refer to the release notes for driver version numbers and information about

potential installation issues.

Installing on Windows 98 or Windows Me

Reflex USB Reader Installation Guide 5

Installing on Windows 98 or Windows Me

To install the SchlumbergerSema Reflex USB smart card reader on a

Windows 98 or Windows Me computer, follow these steps, which are

described in detail in the sections that follow:

1Install the new Reflex USB smart card reader software.

2Connect the Reflex USB smart card reader.

3Reboot the computer.

Step 1: Install the Reflex USB smart card reader software

Go to the Reflex Readers Download website (www.reflexreaders.com/

Support/Downloads/downloads.html) to download the latest Reflex USB

driver package for Win98/Me. If the Microsoft Base Components are not

already installed on your computer, you will also need to download and install

that software.

See the package’s Install Notes for installation instructions.

Step 2: Connect the Reflex USB smart card reader

Insert the Reflex USB smart card reader cable connector into the USB port.

The Reflex USB smart card reader is compliant with Plug-and-Play

specifications, so you can make the connection while the computer is running.

The Reflex USB smart card reader power light glows continuously to indicate

that the reader is receiving power, and the computer automatically begins to

scan for Plug-and-Play-compliant hardware. Displayed messages report that

the system has found the new hardware, and has located and installed the

software for it.

Step 3: Reboot the computer

The Windows 98 and Windows Me operating systems detect the Reflex USB

smart card reader as soon as it is connected to the host computer, but the

Smart Card Resource Manager detects it only during reboot or restart.

Therefore, although you will see the Reflex USB smart card reader listed in the

DeviceManager as an installed device after you complete step 2, the Reflex

USB smart card reader is not usable until you reboot.

Refer to the release notes for driver version numbers and information about

potential installation issues.

Chapter 2 - Installation

6Reflex USB Reader Installation Guide

These are other situations that require you to reboot your computer:

•If you connect the Reflex USB smart card reader in mid-session, the Smart

Card Resource Manager is unaware of the change until you reboot.

•If you remove the Reflex USB smart card reader and then reconnect to it,

the Reflex USB smart card reader does not function until you reboot.

•If you remove the Reflex USB smart card reader without first stopping the

device, these errors display:

Reader removal monitor error retry threshold

reached. The parameter is incorrect.

Reader monitor ‘Schlumberger Reflex USB 0’ received

uncaught error code: The parameter is incorrect.

To make the Reflex USB reader functional, reconnect it and reboot.

At this point you are ready to start using the Reflex USB smart card reader.

You can test the reader setup using the Smart Card Reader Tools. From the

Start menu on the Windows taskbar, select Programs →Schlumberger

Smart Cards and Terminals →Smart Card Readers →Tools.

Updating on Windows 98 or Windows Me

To update the Reflex USB smart card reader software, complete these tasks,

which are described in detail in the sections that follow:

1Install the new Reflex USB smart card reader software.

2Step through the Update Device Driver wizard.

3Reboot the computer.

Step 1: Install the new Reflex USB smart card reader software

Go to the Reflex Readers Download website (www.reflexreaders.com/

Support/Downloads/downloads.html) to download the latest Reflex USB

driver package for Win98/Me.

See the package’s Install Notes for installation instructions.

Step 2: Step through the Update Device Driver wizard

Use the operating system’s Update Device Driver wizard to point the operating

system to the new driver:

Refer to the release notes for driver version numbers and information about

potential installation issues.

Table des matières

Autres manuels Schlumberger Lecteur de cartes

Schlumberger

Schlumberger Reflex 72 Manuel utilisateur

Manuels Lecteur de cartes populaires d'autres marques

Lindy

Lindy 43185 Manuel utilisateur

Lindy

Lindy 43185 Manuel utilisateur

ViziT

ViziT RD-4F Manuel utilisateur

Jinmuyu Electronics

Jinmuyu Electronics MR811 Series Manuel utilisateur

AVID ID

AVID ID AVID1043 Manuel utilisateur

Conrad

Conrad PCMCIA Manuel utilisateur

Rosslare

Rosslare DR-6255 Manuel utilisateur

Lindy

Lindy 51541 Manuel utilisateur

Diapro T?bbi Ürünler

Diapro T?bbi Ürünler Across System Manuel utilisateur

Johnson Controls

Johnson Controls Kantech tyco ioSmart Manuel utilisateur

ACS

ACS ACR122L Manuel utilisateur

Secukey

Secukey S2-MF Manuel utilisateur

Elecom

Elecom MR-SMC07 series Manuel utilisateur

Alien

Alien ALR-9800 Manuel utilisateur

ACS

ACS ACR310 Manuel utilisateur

Datamars

Datamars R-IN1300 MID Manuel utilisateur

Alarm Lock

Alarm Lock AL-PRE2 Manuel utilisateur

xpr

xpr B100PROX-AH Guide de l'utilisateur