Schletter FIXGRID PRO-100 Manuel utilisateur

FIXGRID PRO EAST-WEST | 800440-100EN | V1 | ASSEMBLY INSTRUCTIONS | VERSION: 2023 / 01 | WWW.SCHLETTER-GROUP.COM
Subject to modifications
1
(18)
FIXGRID PRO-100
ASSEMBLY INSTRUCTIONS
TABLE OF CONTENTS
ROOF SYSTEMS FLAT ROOF BALLASTING SOLUTIONS
Assembly instructions
for east-west orientation
1 General Information����������������������������������������������������������������� 2
Tools Needed �������������������������������������������������������������������������� 2
Other Documents Required������������������������������������������������������ 2
Tightening Torques������������������������������������������������������������������ 2
Safety Instructions ������������������������������������������������������������������ 2
Installation Instructions������������������������������������������������������������ 3
2 Versions���������������������������������������������������������������������������������� 4
3 Defining base profile lengths and module support distances ����� 6
4 Inserting the Pro front screw-in module support ���������������������� 7
5 Inserting the Pro screw-in heightening elements ���������������������� 8
6 Extending the Pro heightening element������������������������������������ 9
7 Extending the Pro module support ����������������������������������������� 10
8 Mounting the surface protection mat ��������������������������������������11
9 Connecting the floor profile ����������������������������������������������������13
10 Aligning the floor profile �������������������������������������������������������13
11 Ballasting����������������������������������������������������������������������������� 14
12 Solar module installation�������������������������������������������������������18
EN

FIXGRID PRO EAST-WEST | 800440-100EN | V1 | ASSEMBLY INSTRUCTIONS | VERSION: 2023 / 01 | WWW.SCHLETTER-GROUP.COM
Subject to modifications
2
(18)
1 GENERAL INFORMATION
TOOLS NEEDED
• Tape measure
• Screwdriver with TX drive T40 bit Module installation
• Screwdriver with SW8 socket wrench Windsafe Pro installation
• Schletter screw-in aid Module support installation and screw-in heightening element
• Screwdriver or SW24 fork spanner to create leverage
Installation of ballast and composite rail using RapidCon90 cross connector
• Flat pliers For ballast version C
OTHER DOCUMENTS REQUIRED
• General installation manual – installation and project planning
• Installation manual RapidPro module clamps
• Product sheet FixGrid Pro-100
• Project-related planning and ballasting documents
TIGHTENING TORQUES
• Screw connections M8: 15 Nm
• Use of self-drilling screws: stop-oriented
SAFETY INSTRUCTIONS
Break hazard! PV modules may be damaged if stepped on�
Planning, installation and commissioning of the solar power system must only be performed
by qualified technical personnel� Improper execution can result in damage to the system and
endanger persons�
Electrical current hazard! Installation and maintenance of the PV modules must only be performed by
qualified technical personnel� Observe the safety instructions issued by the PV module manufacturer!
Falling hazard! Working on the roof as well as ascending and descending poses a risk of falling�
It is vital to observe accident prevention regulations and use appropriate fall protection equipment�
Hazard area! Prior to installation, set up barriers
to warn people who are in the vicinity�

FIXGRID PRO EAST-WEST | 800440-100EN | V1 | ASSEMBLY INSTRUCTIONS | VERSION: 2023 / 01 | WWW.SCHLETTER-GROUP.COM
Subject to modifications
3
(18)
INSTALLATION INSTRUCTIONS
Roof pitch and securing against slipping: Due to thermal linear expansion, so-called caterpillar
effects can occur� It has to be checked in each individual case whether an additional fixation
to prevent slipping is required� We recommend a basic fixation from a roof pitch > 5°�
In some circumstances, fixation should be carried out for minor slopes�
Thermal separation of the module blocks must be ensured�
The system must only be installed with ballasting according to the planning documents� The required
ballasting and related planning documents can be determined in the Schletter Configurator�
Check that the existing roofing has been adequately fixed�
Sufficient roof cover must be checked on site�

FIXGRID PRO EAST-WEST | 800440-100EN | V1 | ASSEMBLY INSTRUCTIONS | VERSION: 2023 / 01 | WWW.SCHLETTER-GROUP.COM
Subject to modifications
4
(18)
2 VERSIONS
LANDSCAPE
Version 5° Landscape
Version 10° Landscape
Version 15° Landscape
Detail A
Modulewidth
Support spacing
A
Modulewidth
Support spacing
A
100
100
Modulewidth
Support spacing
A100
Maintainance
Maintainance
Maintainance

FIXGRID PRO EAST-WEST | 800440-100EN | V1 | ASSEMBLY INSTRUCTIONS | VERSION: 2023 / 01 | WWW.SCHLETTER-GROUP.COM
Subject to modifications
5
(18)
Modulewidth
Support spacing
B
Modulewidth
Support spacing
B
100
100
Modulewidth
Support spacing
B100
Maintainance
Maintainance
Maintainance
Detail B
LANDSCAPE PLUS
Clamping at the quarter point of the
modules in case of increased snow loads
Version 5° Landscape Plus
Version 10° Landscape Plus
Version 15° Landscape Plus

FIXGRID PRO EAST-WEST | 800440-100EN | V1 | ASSEMBLY INSTRUCTIONS | VERSION: 2023 / 01 | WWW.SCHLETTER-GROUP.COM
Subject to modifications
6
(18)
3 DEFINING BASE PROFILE LENGTHS AND MODULE SUPPORT DISTANCES
The distances of the heightening and support elements depend on the module size
and are shown accordingly in the project-related structural analysis report�
LANDSCAPE
LANDSCAPE PLUS
The modules are to be clamped flush at the upper and lower module support�
Detail A
Detail B
Modulewidth
Support spacing
A100
Maintainance
Modulewidth
Support spacing
B100
Maintainance

FIXGRID PRO EAST-WEST | 800440-100EN | V1 | ASSEMBLY INSTRUCTIONS | VERSION: 2023 / 01 | WWW.SCHLETTER-GROUP.COM
Subject to modifications
7
(18)
Mark position according to planning
documents
Place screw-in aid in position on the base profile
Insert Pro module support parallel to Pro
base profile in assembly aid (insert pressed-
in screw-in connector into click channel)
Turn the screw-in aid 90° clockwise
Lift the screw-in aid slightly
Pull the screw-in aid sideways off the base profile
4 INSERTING THE PRO FRONT SCREWIN MODULE SUPPORT
2
1
4
3 5
6

FIXGRID PRO EAST-WEST | 800440-100EN | V1 | ASSEMBLY INSTRUCTIONS | VERSION: 2023 / 01 | WWW.SCHLETTER-GROUP.COM
Subject to modifications
8
(18)
Turn the screw-in aid 90° clockwise
Lift the screw-in aid slightly
Pull the screw-in aid sideways off the base profile
Determine the distance to the screw-
in module support according to the
assembly instructions (see chapter 2)
Place screw-in aid in position on the base profile
Insert Pro module support parallel to Pro
base profile in assembly aid (insert pressed-
in screw-in connector into click channel)
5 INSERTING THE PRO SCREWIN HEIGHTENING ELEMENTS
2
4
3
5
6
1

FIXGRID PRO EAST-WEST | 800440-100EN | V1 | ASSEMBLY INSTRUCTIONS | VERSION: 2023 / 01 | WWW.SCHLETTER-GROUP.COM
Subject to modifications
9
(18)
Fit Pro heightening extension element on
existing slightly inclined element (short side
to short side - groove to right-angled arm)
Click in on long side
6 EXTENDING THE PRO HEIGHTENING ELEMENT
OVERVIEW OF THE REQUIRED NUMBER OF REAR PRO
HEIGHTENING ELEMENTS FOR LANDSCAPE ASSEMBLY
5° 10° 15°
Pro module support 1 1 1
Pro heightening element – 1 2
Pro screw-in heightening
element
1 1 1
The Pro screw-in heightening element can also be used instead of the Pro heightening element�
The Pro screw-in module support can also be used instead of the Pro module support�
1 2

FIXGRID PRO EAST-WEST | 800440-100EN | V1 | ASSEMBLY INSTRUCTIONS | VERSION: 2023 / 01 | WWW.SCHLETTER-GROUP.COM
Subject to modifications
10
(18)
Place Pro module support on Pro
heightening element at a slight angle
Click in on long side
7 EXTENDING THE PRO MODULE SUPPORT
1 2
Table des matières

















