Schleifenbauer PDU Manuel utilisateur



 

V2.52 Schleifenbauer PDU

User manual



Page 1 of 54

V252_User manual

Schleifenbauer PDU




Index 

Layout of this manual 4
UC_What’s new 4
Introduction 5
Power distribution meets intelligence 5
Interfaces 5
Accessories 5
Colored housing 6
Measurements 6
Part I - Installation of hardware 7
Safety warnings 7
Expert personnel 7
Technical installation requirements 7
Visual inspection 7
Testing 8
Cleaning 8
Contents of the package 8
Additionally needed tools 8
Mounting the PDU in cabinets 8
How to mount a PDU horizontally (19 inch)? 8
How to mount a PDU vertically (= 0U)? 9
How to install on a flat surface?...table top mount 9
How to prevent hot spots in a cabinet? …sunken installation
9
How to mount a PDU without tools? 9
How to achieve maximum mounting flexibility? ...mounting
with profile clamps 9
Cabling the PDU: ethernet, databus and sensors 10
How to connect the PDU to LAN? 10
How to connect a databus? 10
How to connect sensors to a PDU? 10
How to connect a NO/NC contact on Classic PDU and
ethernet PDU? 11
How to connect NO/NC contact on a g3 PDU? 11
Part II - User manual 12
How to maintain a PDU? 12
How to be sure the status of switchable outlets will not
change during firmware upgrade or restarting of the
controller? 12
Life-Supporting Policy 12
Part IIA - Locally monitoring: device display 13
How to change settings locally via PDU display? 13
How to stop a blinking display? … local alert reset 14
Why do alerts occur? 14
How to check the load balance, the temperature / humidity
or the status of the NO/NC contact? 14
How to get back to the first page? 15
How to check an outlet status locally? 15
How to check input and/or outlet measurements? 15
How to read measurements of optional sensors and what
options are possible? 16
Option 1: load page 16
Option 2: sensor pages 16
How to read Branch Residual Current measurements? 17
Data center practice: Residual Current Monitoring in
relation to Residual Current Devices 17
Where to measure residual current? 17
How to find the PDUs unit address, tag, name or location? 17
How to check the way the PDU is connected to the LAN? 18
How can I check in which mode and with what protocol the
PDU is running? 18
How to check the installed firmware version? 19
How to check for traceability information ? 19
Part IIB - Remote operating and monitoring: Web interface 20
Introduction 20
How to enlarge a pane in L sized screens? 21
How to select English or German language? 21
How to change and save settings in the web interface? 21
Dashboard – tab 22
System status 22
Load 25
Interfaces 25
Sensors – tab 26
Inputs – tab 27
Outlets – tab 28
System – tab 30
Identification 31
Configuration 32
Reset 32
Settings 33
Interfaces – tab 36
Part III - Administrator manual 37
Specific manuals 37
How to change SNMPv3 settings? 38
How to use the ‘connected devices’ section in the web
interface? 39
How to add new devices on an existing ring? How to solve
duplicate devices? 39
How about login profiles, usernames and passwords? 40
How to change factory passwords? 41
How to change the Ethernet link settings? 41
Network configurations 42
DHCP and default address 42
How to configure the IP settings manually? 42
How to setup IPv6? 43
IPv6 Autoconfigure (SLAAC) 43
Static IP 43
How to configure IPv6? 44
How to set up IPv6 address filtering? 45
How to send SNMP Traps with IPv6? 45
How to stop the alert signaling? ...auto reset alert 46
Firmware downgrade / upgrade 46
How to upgrade the firmware? ...using SPST 46
How to upgrade the firmware? ...using USB 47


Page 2 of 54
 V252_User manual
Schleifenbauer PDU




Schleifenbauer databus: what is it? 48

How to prevent data losses because of cable cuts? ...ring

redundancy 49

How to make a databus using Schleifenbauer Gateway? 50

How to connect the databus to LAN without a Gateway?

...using a PDU! 51

PART IV - Problem Solving 52

How to perform a “Software reset”? And why? 52

Remotely 52

Locally 52

How to perform a “Factory reset”? 52

How to reset peak current?.....and other dips or peaks 53

Recycling 54

PRODUCT SPECIFICATIONS 54

SERVICE AND SUPPORT 54



Page 3 of 54

V252_User manual

Schleifenbauer PDU



LAYOUT OF THIS MANUAL

This manual is split in three sections. You can focus on the section that fulfills your need when installing, operating and/or

managing the PDU.



The “How to....” section is meant to guide you directly to a solution for a problem you are faced with. It is not necessary to

read the complete manual.



Part I

Installation manual

Prepare PDU for use:



●safety issues

●mounting the PDU

●cabling the PDU



Part II

User manual

Operator and user part:



●operating/read out via the PDU-display

●operating/read out via the web interface

●problem solving



Part III

Administrator manual

Admin part:



●configure via the web interface

●set up via the web interface

●problem solving



Part IV

Problem Solving

In this chapter you can find the frequently asked questions

(FAQs)



WHAT’S NEW

●Firmware upgrade via USB port

●Near zero cross switching of outlet relays

●Support for 54 metered and/or switched outlets

●Voltage drop alert is now based on the input line voltage rather than a fixed value for 120 and 230 Volt operation.



Page 4 of 54

V252_User manual

Schleifenbauer PDU



INTRODUCTION

POWER DISTRIBUTION MEETS INTELLIGENCE

The Schleifenbauer Intelligent Power Distribution Unit (PDU) is designed to distribute power for many years and without

problems. It is equipped with a Schleifenbauer databus which makes it possible to read and manage many PDUs with a

single IP address. An ethernet port was added to the individual PDUs so that alongside the advantages of a databus, a

whole range of new options has become available.

Schleifenbauer PDUs bring together or merges the interests between IT and infrastructures, making it a real bridge builder.

The PDU may contain:

●metered outlets

●switched outlets

●metered and switched outlets

●passive outlets

Monitoring capabilities will be described in detail within this manual in coming sections.

INTERFACES

In the Admin part of this manual you will find information about the “Interfaces” with which we mean the technology to

communicate via your LAN with the Schleifenbauer databus. There are several possibilities:

●(embedded) web interface

●Modbus/TCP

●SNMP

(Simple Network Management Protocol)

●(SP)API

(Schleifenbauer Products Application Programming Interface)

ACCESSORIES

The following accessories can be purchased from Schleifenbauer, additionally. Please check the Installation Section for

more details regarding mounting brackets.

●C14/C20 plugs if C13/C19 outputs are used

●Different types of attachment brackets

o19” rack mounting brackets

oTabletop mounting brackets

oMounting plates for sunken installation

oProfile clamps

oToolless Mounts

●Customer Specific solutions related tools



Please check www.schleifenbauer.eu for further details regarding the accessories.

 



Page 5 of 54

V252_User manual

Schleifenbauer PDU



COLORED HOUSING



Standard the housing color of the Schleifenbauer PDUs is black. It is also possible to anodizing the housing in 5 other

colors.



01. black

02. green 

03. orange

04. blue

05. red

06. Yellow



Not shown but available is “natural”



Note:



actual colors may vary!

MEASUREMENTS

Measurements of the input and the outlet level can be found below:



Measurement

Unit

Remark

Energy

(kWh)

total & subtotal

Voltage

(V)

with voltage dip registration

Current

(A)

with peak value registration and drop detection.

Power factor

(%)



Apparent power

(VA)



Real power

(W)



Temperature

(°C)

with optional sensor

Relative humidity

(%)

with optional sensor

NO/NC contact

0-2

devices equipped with a USB-port can operate two NO/NC contacts

(see chapter “How to connect a NO/NC contact)



 



Page 6 of 54

V252_User manual

Schleifenbauer PDU



PART I - INSTALLATION OF HARDWARE

Please use the information in this chapter to inspect, install and connect the Schleifenbauer Intelligent PDU and all

optional mentioned accessories.



The PDU must be installed in a restricted access location

Socket-outlet must be installed near the equipment

Socket-outlet must be easily accessible

Installation by expert personnel only

After installation: default passwords / RC4 keys MUST be changed (see: Part III - Administrator manual)

SAFETY WARNINGS

This manual contains important safety instructions that should be followed during installation and operation of the PDU.

Please read this manual carefully since there may be serious or fatal personal injury and damage to the equipment if the

safety instructions, warnings and directions are not followed. Please save this document for future use.

EXPERT PERSONNEL

Installation, maintenance and inspection of the Schleifenbauer Intelligent PDU must be carried out by adequately trained

persons according to NEN EN 50110-1, with full observance of the specifications of NEN EN 50110-1 and NEN 3140.

TECHNICAL INSTALLATION REQUIREMENTS

Before installing and putting the system into operation, check whether the characteristics of the electrical system to which

connection is to be made correspond to the product specifications.

●The Schleifenbauer Intelligent PDU has been designed for connection to electrical systems that comply with IEC

60364 or in the Netherlands, NEN 1010.

●The voltage, maximum permitted current and the number of phases must be correct. This information is

displayed on the front side of the PDU.

●The maximum permitted power must be taken into account with regard to the maximum length and the diameter

of the connecting lead.

●The values and characteristics of the in-series protective devices must match the PDU and the protective

elements included in it.

●The environmental factors must correspond to the product specifications.

VISUAL INSPECTION

After opening the cardboard box and removing the packaging material, the PDU should be checked visually. The PDU

should not be put into operation if damage is detected such that safe and proper operation cannot be guaranteed. In such

cases, please contact Schleifenbauer Products BV.

Note that, in the case of PDUs that are equipped with an over voltage protection, the overvoltage protection and the

respective overcurrent protection (if applicable) must be inspected on a regular basis.



Page 7 of 54

V252_User manual

Schleifenbauer PDU



TESTING 

Each Schleifenbauer PDU is individually tested according to the NEN 3140 standard. Test reports are available on request.



For measurement of insulation resistance, the measuring voltage used must be lower than or equal to the

voltage according to the product specification.



CLEANING

The PDU may only be cleaned by wiping off the outside with a clean dry cloth.

CONTENTS OF THE PACKAGE

The Schleifenbauer Intelligent PDUs are shipped in a cardboard box. Where applicable, dispose the packaging material in a

responsible manner, in accordance with local regulations. All of the materials used for packaging can be recycled.

Immediately after receipt, check whether you have received all of the goods.



The following items are delivered for each PDU:

●fixing materials: these can be attached to the PDU (19’’ or table-mounting brackets), or are delivered separately if

they have been ordered separately;

●the installation manual (1 per shipment);



Please note that the PDU User Manual can be found online at http://schleifenbauer.eu

ADDITIONALLY NEEDED TOOLS

The following tools are needed to install the PDUs:

●cage-nuts with bolts and washers

●suitable screwdriver.

MOUNTING THE PDU IN CABINETS

How to mount a PDU horizontally (19 inch)?

Each 19’’ rack bracket of a PDU has holes for horizontal mounting in 19” racks. The holes are

positioned so that an appropriate fixing hole is always available for a PDU with a profile height of

1.5 U. Using one or two of the 4 holes allows mounting without wasting space.



 



Page 8 of 54

V252_User manual

Schleifenbauer PDU



How to mount a PDU vertically (= 0U)?

In the case of a PDU for vertical mounting, the connection lead is fed through a hole in the upper, bottom or front face.

There are 4 options for horizontal mounting:



How to install on a flat surface?...table top mount

Gives the profile possibility to be mounted to a flat surface (tabletop).This

arrangement is used for:

●vertical mounting to the bracing beams in the 19” cabinet

●fixing to a mounting plate

●mounting between the 19” uprights: the profile attaches to the front

of the uprights

The holes on the brackets are located as far as possible to the outside so

that it can also fit and tighten the bolts if a swivel gland has been placed

on the short side.



How to prevent hot spots in a cabinet? …sunken

installation

When power leads might block the flow of hot exhaust air, especially in

case of a 600mm wide cabinet, it is necessary to create flow space. This

can be done by using the “sunken installation brackets”. Because of the

shape of the bracket, it is possible to ‘partially sink’ the profile into the

cabinet and save space.

These mounting plates can be used for many different cabinets.



How to mount a PDU without tools?

Toolless mounting is created by making attachment points on the rear of

the PDU housing. There is a wide range of cabinet brackets available, all in

which you can hang the PDU without using tools.

Toolless Mounting can be done as single PDU or double PDUs (see photo).



Mounting brackets can be custom made by Schleifenbauer.



How to achieve maximum mounting flexibility?

...mounting with profile clamps

The clamps, made of spring steel, can be installed in the position of your

choice. The clamp fits around the PDU profile and is secured with a

fastening screw. Best is to use one clamp for every 50 cm of profile length.



Page 9 of 54

V252_User manual

Schleifenbauer PDU



CABLING THE PDU: ETHERNET, DATABUS AND SENSORS

How to connect the PDU to LAN?

10/100 Mbps LAN Ethernet port

Connecting the PDU to a Local Area Network (LAN) provides

communication through an Ethernet network, if the PDU is connected

exclusively, or simultaneously with the databus.

The RJ45 connector for the network cable must be plugged into the

Ethernet port:

●Connect the RJ45 Ethernet cable to the Ethernet port on the PDU

and to the Ethernet connector on the LAN device; when

connected, the orange LED – marked “lnk” - will blink



How to connect a databus?

There are three black communication ports. One is marked as sensorport,

the other two as databus ports (in and out).

The left databus port is the “incoming” databus port. The right databus

port is “outgoing”. This is a MUST HAVE for devices in bridge mode. For

devices in hybrid mode it is a NICE TO HAVE.

The serial databus in the Schleifenbauer PDU uses CAT5 patch cables.

The terms IN and OUT are arguable. Data will be send and received            

by both ports but to close the databus ring, it is recommended to follow             

the connection diagram. See it as the best way to daisy chain PDUs.



How to connect sensors to a PDU?

The PDU has a RJ12 connector sensor port for connecting a digital

temperature sensor, a combined sensor for temperature/humidity or one

or multiple dry switch contacts.



Plug and play

The PDU registers which sensor is connected and automatically adapts

the menu in the display to the sensor(s) that it has detected.



Use Schleifenbauer sensors only



Page 10 of 54

V252_User manual

Schleifenbauer PDU



Table des matières

Autres manuels Schleifenbauer Unité de distribution d'énergie

Schleifenbauer

Schleifenbauer V2.62 Manuel utilisateur

Manuels Unité de distribution d'énergie populaires d'autres marques

hager

hager SP 015 Manuel utilisateur

Pakedge

Pakedge PowerPak 9 Manuel utilisateur

Pts

Pts 9042 Series Manuel utilisateur

Shure

Shure WA405 Manuel utilisateur

CORNING

CORNING CCH 4U Manuel utilisateur

Panamax

Panamax M4LT-EX Manuel utilisateur

PANCONNECT

PANCONNECT FLAT 3M Manuel utilisateur

Raytheon

Raytheon 138-118 Manuel utilisateur

D&R ELECTRONICS

D&R ELECTRONICS PDU-6SS Manuel utilisateur

Botex

Botex PSA 322-6 DL Manuel utilisateur

GE QuiXtra 4000 Guide de démarrage rapide

RDL

RDL EZ Series Manuel utilisateur

StarTech.com

StarTech.com RKPW161915 Manuel du système

Vertiv

Vertiv Knürr DI-Strip Rack PDU Manuel utilisateur

ABB

ABB PSBS0065 Manuel

Baumuller

Baumuller BFN 3-1-0007-001 Manuel

Eaton

Eaton StructuredWiringSolutions ESWT41600 Manuel

GE GEK-45404F Manuel utilisateur