Schiit Saga S Manuel utilisateur
PASSIVE OR ACTIVE REMOTE PREMP
A PASSIVE RELAY-STEPPED ATTENUATOR? YES.
A DISCRETE JFET BUFFER? YOU BET.
AND REMOTE CONTROL? YEP, THAT’S INCLUDED AS WELL.
SAGA IS A SEERESS IN NORSE MYTHOLOGY,
BUT THE ONLY THING WE’RE SEEING IS THE LOOK OF SHOCK
WHEN YOU DISCOVER THE PRICE OF THIS GREAT LITTLE PREAMP.
SAGA S
OWNER’S MANUAL
The following is required by the roughly 9,542
government agencies and regulations we have to
comply with. If you have some common sense, they
should seem pretty straightforward. In any case, read these
instructions before proceeding farther, follow all instructions,
and heed all warnings. Or else!
1. If you don’t know how to install audio devices, get a
qualied professional to help.
2. Never use this device near water, and clean only with a
dry cloth.
3. Assure adequate ventilation, do not block any ventilation
openings, or place near heat sources.
4. Use only the supplied power cord or suitable replacement.
Route cords away from trafc areas and protect them from
being pinched. Unplug the cord from the outlet if the apparatus
is unused for a long period of time.
5. To prevent electric shock, do not use the plug with an
extension cord, receptacle, or outlet unless blades can be
fully inserted.
6. Refer all servicing to qualied service personnel. Service is
required when the device has been damaged, including cord or
plug damage, liquid has been spilled or objects have fallen into
the device, the device has been exposed to rain or moisture,
does not operate normally, or has been dropped.
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS DEVICE TO
RAIN OR MOISTURE.
Saga S is just like Saga+, but without that pesky
tube. Now, you can have the convenience of an
all-solid-state ultra-high-end preamp, cleverly
disguised with a low price. You won’t nd any
volume-control chips or other shortcuts in
Saga—just uber-quality techniques as used in
the most expensive audio gear. Choose passive
output, or engage the discrete JFET buffer, for
exceptional flexibility.
INTRODUCTION
WHAT’S IN THE BOX
(1) Saga S
(1) Power cord
(0) Pesky tubes
(0) Stick-on feet (they’re pressed in!)
ASSEMBLED IN USA
1 2 3 4 5
1 2 3 4 5 A B
CAUTION: RISK OF ELECTRIC
SHOCK—DO NOT OPEN
NO USER SERVICEABLE
PARTS INSIDE
5 IR Window. The remote “talks” to the Saga S
through this window. Don’t block it, unless you
don’t want the remote to work.
6 Mute Indicator. When Saga S is muted, this LED
will turn on. Saga is muted for 60 seconds on rst
turn-on. You can also mute the preamp at any
time using the remote control.
7 Passive/Buffer Indicator. This lights up when
you’re using the JFET buffer output. It’s off for
passive output.
1 Input. The selected input lights up to indicate
the selected input. Pretty simple, right?
2 Input Switch. Press to choose the input you
want to listen to.
3 Volume Knob. Turn it to the right to make the
music louder. Stop before smoke comes out of
your speakers.
4 Mode Select. Press to change between passive
and buffer output.
CONTROLS
1 2
3
45
6
7
3 On-Off Switch. Up is on. Down is off. If you have
the preamp in a place where you can’t easily reach
it, just plug it in to a power strip or use a remote-
controlled outlet. Yes, those are a thing.
4 AC Input. Plug the power cord in here. Plug the
other end into an outlet of the correct voltage.
Trying to run a 115V product on 230V will blow the
fuse and generally make for a bad, bad day.
1 RCA Inputs.
You can connect up to 5 inputs to Saga S using
RCA cables. The inputs are conveniently num-
bered “1” to “5” to match the front panel indica-
tors. Select the input you want to listen to using
the front panel buttons or the remote control.
2 RCA Outputs.
We’ve provided two sets of RCA outputs here,
so you can connect to 2 amps, or an amp and a
subwoofer, or you can just use a single output.
You don’t have to use both.
ASSEMBLED IN USA
1 2 3 4 5
1 2 3 4 5 A B
CAUTION: RISK OF ELECTRIC
SHOCK—DO NOT OPEN
NO USER SERVICEABLE
PARTS INSIDE
CONNECTIONS
1 2 341 1 1 1 2
REMOTE CONTROL
Yes, this preamp comes with a remote control. Unlike earlier Sagas,
this is now a fancy milled aluminum model. It’s still inexpensive to
replace in case you lose it or want another one, however.
1 Input. Press this button to select the input you want to listen to. If
you skip the input, keep pressing—it cycles back around.
2 Volume Up/Down. Press the up arrow to turn volume up, press the
down arrow to turn it down. Simple as that.
3 Output. Press to change between passive and JFET buffer output.
4 Mute. Press to mute the preamp.
Changing the Battery
1. Flip the remote over to reveal a single hole on the back.
2. Push the remote open by inserting the end of an open paper clip into
the hole in the back and pushing rmly. It’s held together with magnets.
3. Replace the battery inside with one of the same type.
4. Reassemble the remote by rst inserting the clear LED in the front,
then dropping the panel down onto the matching magnets. Press
down gently to pop the panel in place.
Saga/Freya Ragnarok 2 Loki Loki Max
SCH 03-11
SCH 03-13 SCH 03-14
BYPASS
20HZ UP/DOWN
250HZ UP/DOWN
2KHZ UP/DOWN
6KHZ UP/DOWN
16KHZ UP/DOWN
BYPASS
PRESET 1
PRESET 2
PRESET 3
20HZ UP/DOWN
120HZ UP/DOWN
400HZ UP/DOWN
2KHZ UP/DOWN
6KHZ UP/DOWN
16KHZ UP/DOWN
VOLUME
INPUT
OUTPUT
MUTE
SCH 03-12
VOLUME
INPUT
OUTPUT
MUTE
GAIN
Sleipnir/Ellida
SCH 03-15
PLAY/PAUSE
SKIP FWD
FAST FWD
FAST REV
STOP/EJECT
DISPLAY OFF
SKIP BACK
DACs DACs
SCH 03-16a SCH 03-16b
INPUT
INVERT
MUTE
INPUT SEL
INVERT
MUTE
2
1
3
4
I hear hum, what do I do?
You may have a ground loop. To x a ground loop,
try a ground loop isolator or an EbTech HumX.
There’s no sound for a while after I turn Saga S
on.
That’s perfectly normal. Saga S delays the output
for 60 seconds after you rst turn the preamp on
to help prevent loud noises during start-up.
What’s with the clicking noises when I turn the
volume?
That’s the sound of the mechanical relays in the
relay-switched stepped attenuator. This is totally
normal.
I’m not getting any sound output, but the lights
are on.
Is the mute light on? If so, the preamp is muted.
Unmute the preamp using your remote control.
Otherwise, make sure you’re on the correct input
and the volume is turned up.
FAQ
Can I leave Saga S on all the time?
Yes, you can. Saga S is fully solid-state, so it
does not have any tubes to worry about. Feel
free to leave it on all the time, or turn it on and
off as needed. It’s up to you.
Can I use both outputs at the same time?
Most of the time, yes. If you have products that
short the input when turned off, then that can
cause distortion.
I have the volume all the way down and still
hear faint music.
Yes, that is normal with a relay attenuator. If it’s
bothersome, hit the Mute button on the remote
to completely mute the preamp.
It doesn’t turn on, what do I do?
Plug it in to a different AC socket. Ensure you
are not currently in a blackout. Then email us if
it still doesn’t work.
Schiit Audio warrants to the original purchaser that the product shall be free from defects in material and workman-
ship for ve (5) years from the date of purchase. Exceptions: tubes and remote controls. Tubes are covered by a
90-day limited warranty with the same terms. Remote controls are covered by a 1-year warranty with the same terms.
If a defect covered by this warranty occurs during this warranty period, Schiit Audio will repair the defective product,
free of charge. Date of purchase will be based on customer-submitted receipts, otherwise date of manufacturing will
be used to determine warranty period.
If you believe you need warranty service, CONTACT US rst. There may be a simple solution to your problem. Schiit
Audio products sent back to us without a RETURN AUTHORIZATION (RA) will be returned to the sender without repair.
To contact us and obtain an RA, email [email protected]. We will respond quickly to either phone or email messages.
WARRANTY LIMITATIONS
THIS WARRANTY SHALL NOT APPLY IF THIS PRODUCT: (a) IS MODIFIED OR TAMPERED WITH; (b) IS DAMAGED BY
NEGLIGENCE, ACCIDENT, UNREASONABLE USE, COFFEE, OR BY OTHER CAUSES UNRELATED TO DEFECTIVE
MATERIALS OR WORKMANSHIP; OR (c) HAS HAD THE SERIAL NUMBER ALTERED, DEFACED OR REMOVED.
ANY APPLICABLE IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE HEREBY LIMITED IN DURATION TO THE WARRANTY PERIOD (5 YEARS). IN NO EVENT
SHALL SCHIIT AUDIO BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES RESULTING FROM THE BREACH
OF ANY IMPLIED OR EXPRESS WARRANTIES. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN
IMPLIED WARRANTY LASTS OR EXCLUSION OF CONSEQUENTIAL OR INCIDENTAL DAMAGES, SO THE ABOVE LIMITA-
TIONS MAY NOT APPLY TO YOU.
This warranty gives you specic legal rights. You may also have other rights which vary from state to state or prov-
ince to province.
WARRANTY
SCHIIT.COM
Application for Council Directives 72/23/EEC
Conformity declared for EN60065, EN50082-1
Table des matières
Autres manuels Schiit Amplificateur
Schiit
Schiit TYR Manuel utilisateur
Schiit
Schiit Fulla 3 Manuel utilisateur
Schiit
Schiit Mjolnir SCH-05 Manuel utilisateur
Schiit
Schiit Vali 2 Manuel utilisateur
Schiit
Schiit Freya Manuel utilisateur
Schiit
Schiit Lyr 3 Manuel utilisateur
Schiit
Schiit SHOLL Manuel utilisateur
Schiit
Schiit MANI 2 Manuel utilisateur
Schiit
Schiit Fulla 2 Manuel utilisateur
Schiit
Schiit Asgard 3 Modular Continuity Manuel utilisateur
Schiit
Schiit MAGNI Manuel utilisateur
Schiit
Schiit AEGIR Manuel utilisateur
Schiit
Schiit Jotunheim R Manuel utilisateur
Schiit
Schiit SYS Manuel utilisateur
Schiit
Schiit JOTUNHEIM Manuel utilisateur
Schiit
Schiit REKKR Manuel utilisateur
Schiit
Schiit FOLKVANGR Manuel utilisateur
Schiit
Schiit SCH-21 Manuel utilisateur
Schiit
Schiit Valhalla 2 Manuel utilisateur
Schiit
Schiit ASGARD 2 Manuel utilisateur
