Schertler STAT PRE Manuel utilisateur

Schertler SA

Via Beroldingen 18

6850 Mendrisio

Switzerland

T +41 (0)91 6 0 07 10

F +41 (0)91 6 0 07 11

info@schertler.swiss

www.schertler.swiss

Facebook @schertler.sa

Instagram @schertleraudio

Youtube @Schertler SA

#shareyourschertler

QUICK GUIDE V1

STAT PRE

QUICK GUIDE

THANK YOU

FOR

CHOOSING

SCHERTLER

QUICK START

AT FIRST USE

The 9V battery is already installed on new preamps.

For battery check, plug an instrument cable into the

OUTPUT socket and see that the blue LED lights up.

Repeat this anytime you want to check the battery

status.

To replace an empty battery, remove the 4 screws on

the rear panel’s corners to get access to the battery

compartment.

CONNECTIONS

Connect the instrument cable to the INPUT socket

and the output cable to the OUTPUT socket.

Unplug the OUTPUT to turn off the preamp and save

battery when the preamp is not in use.

LEVEL SET UP

Set the GAIN as needed. Don’t be afraid to even

take it all the way up, if necessary.

EXTERNAL EFFECTS

The use of external effects is only possible in series

and after the STAT PRE.

WARNING: Do not use the STAT PRE with M AG6

guitar pickup, as the 10V provided by the preamp

might damage the pickup.

RELATED PRODUCTS

TEDDY

Stage monitor ARTHUR

Mixer

ACOUSTIC

Amps

CA JM JM

¼”jack cable STAT

pickups

CONNECTIONS

UNBALANCED output

to line channels

(Plug for battery check) UNBALANCED input

from pickup

Thepreamplier requires a 9V battery, which should deliver nearly 500 hours of playing time.

Equipped with a single INPUT and OUTPUT, plus a GAIN control for adjusting the level of input signal,

the preamp is activated when jack cables are inserted into both the INPUT and OUTPUT sockets. (If only

the INPUT is connected, there is no use of battery power.) However, to preserve battery life it is generally

recommended that all cables are disconnected when the preamp is not in use.

To check the battery level, insert a mono jack into the OUTPUT. The blue CHECK light indicates a charged

battery. Thesystem will be ready to work once a jack is also inserted into the INPUT.

To change the battery, carefully remove the four screwsfrom the housing cover, replace the battery, then

replace the screws.

WARNING: Although all ground connections are correctly implemented on the STAT system (pickup,

cables, STAT PRE box and circuit), they are not directly connected to ground (and are therefore “oating”),

as they actually depend on the grounding connection of the device to which the STATsystem is connected.

If that device is not properly grounded, or generates a ground loop, it is possible to experience hum.

Solving the problem requires attention to the device’s ground connection, usually via the GROUND

LIFTswitch.

In short: the ground connection must be provided by the device to which the STAT system is connected.

TECHNICAL INFORMATIONPRACTICAL TIPS

Weight

Dimensions (LxDxH)

Frequency response (@ ± dB)

Construction

Mic In connector

Mic In sensitivity

Mic In impedance

Instrument In connector

Instrument In sensitivity

Instrument In impedance

Return connector

Return sensitivity

Return impedance

Master Out connector

Master Out level

Master Out impedance

Warm

Low Cut

Phantom power (nominal)

Stat power (10 VDC)

Preamp

Audio transformer

Supply

0.16 kg

10. x 5.5 x 2.5 cm

40 Hz to 20 kHz

Aluminum box

n.a.

1/4” jack unbalanced

0 dBu

25 kΩ

n.a.

1/4” jack unbalanced

8 dBu

190 Ω

1st order Low pass (cut freq. 2 kHz) always on

2nd order High pass lter (cut freq. 100 Hz) always on

Yes

Class-A, no negative feedback

9 V alkaline battery

Autres manuels pour STAT PRE

Autres manuels Schertler Amplificateur

Schertler

Schertler GIULIA X Manuel utilisateur

Schertler

Schertler ROY Manuel utilisateur

Schertler

Schertler Giulia Y Manuel utilisateur

Schertler

Schertler DAVID X Manuel utilisateur

Schertler

Schertler GIULIA X Manuel utilisateur

Schertler

Schertler Giulia Manuel utilisateur

Schertler

Schertler UNICO X Manuel utilisateur

Schertler

Schertler JAM X Manuel utilisateur

Schertler

Schertler Arthur ART48 Subgroup Manuel utilisateur

Schertler

Schertler JAM X Manuel utilisateur

Schertler

Schertler Yellow Single Manuel utilisateur

Schertler

Schertler arthur ART48-MICIN/MIC-ULN Manuel utilisateur

Schertler

Schertler Jam 100 Manuel utilisateur

Schertler

Schertler LaFaro DELUXE Manuel utilisateur

Schertler

Schertler Yellow Blender Manuel utilisateur

Schertler

Schertler GIULIA X Manuel utilisateur

Schertler

Schertler Yellow Single Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur

Schertler

Schertler STAT PRE PS Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur

Schertler

Schertler JAM 150 Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur

Schertler

Schertler DAVID X Manuel utilisateur

Schertler

Schertler Yellow Blender Manuel utilisateur

Manuels Amplificateur populaires d'autres marques

ASTRO

ASTRO HVO V40 P Manuel utilisateur

Marantz

Marantz SUPERSCOPE BLA-545 Instructions de montage

NAD

NAD CI980 Manuel utilisateur

Technics

Technics SE-CH770 Manuel utilisateur

Harman Kardon

Harman Kardon HK6300 Manuel utilisateur

NAD

NAD T975 Manuel utilisateur

McIntosh

McIntosh MA6850 Manuel utilisateur

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuel utilisateur

Viatron

Viatron Autrix Manuel utilisateur

GME

GME GA9800 Manuel utilisateur

Atlas

Atlas CP700 Manuel utilisateur

Roland

Roland KC-1000 Manuel utilisateur

Pyle

Pyle PFMRA350BW Manuel utilisateur

Advantage

Advantage S-250 Manuel utilisateur

IRT Electronics

IRT Electronics DVA-3007 Manuel utilisateur

Dimavery

Dimavery BA-100 Series Manuel utilisateur

Sony

Sony XM-S400D Manuel utilisateur

Phonic

Phonic XP 3000 Manuel utilisateur