Schaub Lorenz SL 13600 Manuel utilisateur

SERVICE MANUAL

SL 13600

Design and specifications are subject to change without notice.

VIDEO CASSETTE RECORDER

ORIGINAL

MFR'S VERSION A

SERVICING NOTICES ON CHECKING

As for the places which need special attentions,

they are indicated with the labels or seals on the

cabinet, chassis and parts. Make sure to keep the

indications and notices in the operation manual.

PERFORM A SAFETY CHECK AFTER

SERVICING

Confirm that the screws, parts and wiring which

were removed in order to service are put in the

original positions, or whether there are the

portions which are deteriorated around the

serviced places serviced or not. Check the

insulation between the antenna terminal or

external metal and the AC cord plug blades.

And be sure the safety of that.

2. USE THE DESIGNATED PARTS

The parts in this equipment have the specific

characters of incombustibility and withstand

voltage for safety. Therefore, the part which is

replaced should be used the part which has

the same character.

Especially as to the important parts for safety

which is indicated in the circuit diagram or the

table of parts as a mark, the designated

parts must be used.

1. KEEP THE NOTICES 3. PUT PARTS AND WIRES IN THE

ORIGINAL POSITION AFTER

ASSEMBLING OR WIRING

There are parts which use the insulation

material such as a tube or tape for safety, or

which are assembled in the condition that

these do not contact with the printed board.

The inside wiring is designed not to get closer

to the pyrogenic parts and high voltage parts.

Therefore, put these parts in the original

positions.

A1-1

Remove the Top Cabinet and Front Cabinet.

(Refer to item 1 of the DISASSEMBLY INSTRUCTIONS.)

Remove the screw (1) of the Deck Chassis and remove the Loading Motor.

Rotate the Pinch Roller Cam in the direction of the arrow by hand to slacken the Video Tape.

Rotate the Clutch Ass'y either of the directions to wind the Video Tape in the Cassette Case.

Repeat the above step 3~4. Then take out the Video Cassette from the Deck Chassis. Be careful not to

scratch on the tape.

TAPE REMOVAL METHOD AT NO POWER SUPPLY

Pinch Roller Cam

Main Cam Clutch Ass'y

Main Chassis (Front Side)

Loading Motor

Screw (1)

Capstan DD Unit

Please include the following informations when you order parts. (Particularly the VERSION LETTER.)

1. MODEL NUMBER and VERSION LETTER

The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be

found at the end of the SERIAL NUMBER.

2. PART NO. and DESCRIPTION

You can find it in your SERVICE MANUAL.

HOWTO ORDER PARTS

CONTENTS

A1-1

A2-1

A3-1~A3-4

B1-1

B2-1~B2-6

B3-1, B3-2

C1-1, C1-2

C2-1

C3-1, C3-2

C4-1

D1-1

D2-1~D2-4

D3-1~D3-3

E-1, E-2

E-3, E-4

E-5, E-6

E-7, E-8

F-1, F-2

F-3, F-4

G-1, G-2

G-3, G-4

G-5, G-6

G-7, G-8

G-9, G-10

G-11, G-12

G-13, G-14

G-15, G-16

H-1

I1-1

I2-1, I2-2

J1-1

J2-1

J3-1, J3-2

A2-1

SERVICING NOTICES ON CHECKING......................................................................................

HOW TO ORDER PARTS............................................................................................................

TAPE REMOVAL METHOD AT NO POWER SUPPLY ............................................................

CONTENTS...................................................................................................................................

GENERAL SPECIFICATIONS.....................................................................................................

DISASSEMBLY INSTRUCTIONS

1. REMOVAL OF MECHANICAL PARTS AND P. C. BOARDS............................................

2. REMOVAL OF VCR DECK PARTS ....................................................................................

3. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC...............................................

KEY TO ABBREVIATIONS .........................................................................................................

ERROR CODE LIST.....................................................................................................................

SERVICE MODE LIST .................................................................................................................

PREVENTIVE CHECKS AND SERVICE INTERVALS ..............................................................

WHEN REPLACING EEPROM (MEMORY) IC...........................................................................

SERVICING FIXTURES AND TOOLS ........................................................................................

PREPARATION FOR SERVICING..............................................................................................

MECHANICAL ADJUSTMENTS .................................................................................................

ELECTRICAL ADJUSTMENTS...................................................................................................

BLOCK DIAGRAMS

Y/C/AUDIO/HEAD AMP............................................................................................................

SYSTEM CONTROL/SERVO/TIMER ......................................................................................

HI-FI/DEMODULATOR/21PIN/VPS/TUNER ...........................................................................

DISPLAY/OPERATION/POWER .............................................................................................

PRINTED CIRCUIT BOARDS

SYSCON/AUDIO/OPERATION................................................................................................

SYSCON/AUDIO ......................................................................................................................

SCHEMATIC DIAGRAMS

Y/C/AUDIO/HEAD AMP............................................................................................................

SYSTEM CONTROL/SERVO/TIMER ......................................................................................

POWER .....................................................................................................................................

DISPLAY ...................................................................................................................................

HI-FI/DEMODULATOR .............................................................................................................

21PIN/VPS/TUNER ..................................................................................................................

OPERATION .............................................................................................................................

INTERCONNECTION DIAGRAM ................................................................................................

WAVEFORMS...............................................................................................................................

MECHANICAL EXPLODED VIEW ..............................................................................................

CHASSIS EXPLODED VIEWS ....................................................................................................

MECHANICAL REPLACEMENT PARTS LIST ..........................................................................

CHASSIS REPLACEMENT PARTS LIST...................................................................................

ELECTRICAL REPLACEMENT PARTS LIST............................................................................

GENERAL SPECIFICATIONS

G-1 VCR System VHS Player / Recorder

System Video System PAL

Hi-Fi STEREO Yes

NTSC PB(PAL60Hz) Yes

Deck DECK OVD-7

Loading System Front

Motor 3

Heads Video Head 4Head

FM Audio Head 2Head

Audio /Control Mono/Yes

Erase(Full Track Erase) Yes

Tape Rec PAL SP/LP

Speed NTSC -

Play PAL SP/LP

NTSC SP

t F

win

Tim

(

Appr

)

t +2

oFF:1'12"/REW:1'12"

with Cassette E-180

Forward/Reverse NTSC or PAL-M SP=3x,5x

Picture Search PAL or SECAM SP/LP=5x,7x / 7x, 13x

Frame Advance Yes

Slow Speed Approx. 1/5, 1/10, 1/30

G-2 Tuning Broadcasting System CCIR+Italy System BG

System Tuner and System 1Tuner

Receive CH Destination Oscar (W/ HYPER)

Tuning System F-Synth

Input Impedance VHF/UHF 75 OHM

CH Coverage E2~E4, X~Z+2, S1~S10,

E5~E12,S11~S41,E21~E69

Intermediate Picture(FP) 38.9MHz

Frequency Sound(FS) 33.4MHz

FP-FS 5.5MHz

Auto Guide Ch Area -

Auto Tuning Method ALL Band (Not C.C.I.R. CH Plan)

Preset CH 80CH

RF Converter Output Yes

Channel 23~69 ch

Level/Impedance 73 dBu / 75 Ohm

Sound Selector No

Stereo/Dual TV Sound G-ST

Tuner Sound Muting Yes

G-3 Power Power Source AC 230V, 50Hz

DC -

Power Consumption (at AC) 11 W at 230 V 50Hz

Stand by (at AC) 3 W at 230 V 50Hz

Per Year -

Protector Power Fuse Yes

Dew Sensor No

G-4 Regulation Safety CE

Radiation CE

G-5 Temperature Operation

- 4

Storage -2

G-6 Operating Humidity Less than 80% RH

G-7 Signal Video Signal Input Level 1 V p-p/75 ohm

Output Level 1 V p-p/75 ohm

S/N Ratio (Weighted) 53 dB

Horizontal Resolution at SP Mode 240Line

Audio Signal Input Level -3.8dBm/50Kohm

(0dB=0.775Vrms) Output Level -3.8dBm/1 Kohm

S/N Ratio at SP (Weighted) 42 dB

Harmonic Distortion at SP (1KHz)

pical 1.5%

Frequency Response at SP 100Hz ~10kHz

at LP 100Hz ~5kHz

at SLP -

Hi-Fi Audio Signal Dynamic Range : More than 75 dB

Frequency Response 20Hz ~20kHz

Wow And Flutter : Less than 0.01 %Wrms

Channel Separation : More than 60 dB

Harmonic Distortion : Less than 1.0 %

G-8 On Screen Menu Yes

Display Menu Type Character

ATS No

Timer Rec Set Yes

Auto Repeat On/Off Yes

VCR Set-Up No

Color System No

A3-1

GENERAL SPECIFICATIONS

NICAM Auto/Off No

BBE On/Off No

CH Set-Up Yes

CH Tuning Yes

Auto Tuning Yes

CH Mapping Yes

Guide CH Set No

System Set-Up Yes

Clock Set Yes (Calendar , 24H)

Language Yes

AV2 DEC/AV Yes

RF Output G/K/I No

G-CODE(or SHOWVIEW or PLUSCODE)No. Entry No

NICAM 1/2,NICAM Off,Audio Output No

Stereo,Audio Output,Bilingual Yes

Play/Stop/FF/Rew/Rec/OTR (ITR) /T-Rec/Pause/Eject/Tape In

mbol Mark) Yes

Others CH/AV (LINE) Yes

Clock Yes

Repeat No

Tape Counter Yes

Index Yes

Tape Speed Yes

Manual Tracking (Bar Setting) Yes

Hi-Fi Yes

Zero Return Yes

VPS No

PDC No

TEST Signal Yes

G-9 OSD Language Eng / Ger / Fre / Spa / Ita

G-10 Clock,Timer Calendar 1990/1/1 ~ 2081/12/31

and Timer Timer Events 8 prog/1 month

Back-up One Touch Recording Max Time SP/LP:6 Hours

OTPB Valid Time -

Timer Back-up (at Power Off Mode) 30 min.

G-11 Display Indicator Yes

Indicator Type LED Module (Green + Red)

Clock/Counter,CH,Timer Rec, Play, REC Yes

VCR Yes

PM No

Auto Tuning Yes

RF Output CH Yes

G-12 Remote Unit RC- ED

Control Glow in Dark Remocon No

Format type NEC

Power Source Voltage(D.C) 3V

UM size x pcs UM-4 x 2 pcs

Total Keys 33 Keys

Keys Power Yes

1 Yes

2 Yes

3 Yes

4 Yes

5 Yes

6 Yes

7 Yes

8 Yes

9 Yes

0 / AV Yes

CH / Tracking Up Yes

CH / Tracking Down Yes

Play / Up No

Play / Up / Slow Yes

Stop/Down Yes

F.Fwd / Right Yes

Rew / Left Yes

Pause No

Pause/Still Yes

Rec/OTR Yes

Eject Yes

Counter Reset Yes

Speed Yes

Timer Rec Yes

Index Yes

TV / VCR Yes

Program Yes

Program / Video Plus+ No

A3-2

GENERAL SPECIFICATIONS

Menu Yes

Enter Yes

Cancel/CH Skip Yes

Call Yes

Zero Return Yes

Clock/Counter Yes

Audio Select Yes

Auto Tracking No

G-13 Features Auto Head Cleaning Yes

Auto Tracking Yes

Index Search Yes

HQ (VHS Standard High Quality) Yes

Auto Power On, Auto Play, Auto Rewind, Auto Eject Yes

Auto Repeat Yes

Auto Power Off Yes

VIDEO PLUS+(SHOWVIEW,G-CODE) No

Auto Set Up (CH Auto Set-Up/Auto Clock) No

ATS No

PDC No

VPS No

BBE Audio No

Remote Control Code 1/2 No

RGB Through No

SQPB (PAL SP Mode) No

G-14 Accessories Owner's Manual Yes

Language Italian

w/Guarantee Card No

Remote Control Unit Yes

Dew Caution Sheet No

Video Cassette Tape No

Battery Yes

UM size x pcs UM-4 x 2 pcs

OEM Brand No

Safety Tip No

Toll Free Insert Sheet No

Quick Set-Up Sheet No

Information Sheet No

75 Ohm Coaxial Cable (0.9m) Yes

type Single shield

U/V Mixer No

DC Car Cord (Center+) No

Guarantee Card Yes

Warning Sheet No

Circuit Diagram No

Antenna Change Plug No

Service Facility List No

Important Safeguard No

Dew/AHC Caution Sheet No

AC Plug Adapter No

AC Cord No

AV Cord (1.2m) No

Registration Card No

PTB Sheet No

300 ohm to 75 ohm Antenna Adapter No

G-15 Interface Switch Power Yes

Play Yes

Channel Up Yes

Channel Down Yes

F.FWD/Cue Yes

Rew/Rev Yes

Eject/Stop Yes

Rec/OTR Yes

Main Power SW No

Indicator Power No

Stand by No

TV/VCR No

T-REC No

Rec/OTR No

Terminals Front Video Input RCA x1 (YELLOW)

Audio Input RCA x 2 (WHITE/RED)

Other Terminal No

Rear Video Input No

Audio Input No

Video Output No

Audio Output RCA x 2 (WHITE/RED)

Euro Scart 2-SCART

A3-3

GENERAL SPECIFICATIONS

VHF/UHF Antenna Input/Output DIN Type

G-16 Set Size Approx. W x D x H (mm) 360 x 229 x 95

G-17 Weight Net (Approx.) 3.2 Kg

Gross (Approx.) 3.8 Kg

G-18 Carton Master Carton No

Content -

Material -

Dimensions W x D x H(mm) -

Description of Origin -

Gift Box Yes

Material Single/Brown

Dimensions W x D x H(mm) 429 x 292 x 168

Pulp Package Yes

Design As Per BUYER 's

Description of Origin No

Drop Test Natural Dropping Quelle Dropping At 2 Edges / 4 Surfaces

Height (cm) 80

Container Stuffing(40' container) 2992 Sets

G-19 Material Cabinet Front PS 94HB

PCB Non-Halogen Demand No

Eyelet Demand No

A3-4

DISASSEMBLY INSTRUCTIONS

1.REMOVAL OF MECHANICAL PARTS

AND P.C. BOARDS

1-1: TOP CABINET, FRONT CABINET AND

OPERATION PCB (Refer to Fig. 1-1)

B1-1

1-3: DECK CHASSIS (Refer to Fig. 1-3)

Fig. 1-3

Deck Chassis

Bottom Plate

(2)

(1) (2)

FE Head

NOTE

Do not remove the cable at the FE Head section.The FE

Head may be damaged if you remove the cable by force.

Remove the screw (1).

Remove the FE Head.

Remove the 3 screws (2).

Disconnect the following connectors:

(CP1001, CP4001, CP4002 and CP4003).

Remove the Deck Chassis in the direction of arrow.

1-2: FLAP (Refer to Fig. 1-2)

Open Flap to 90° and flex in direction of arrow (A), at

the same time slide in direction of arrow (B).

Then lift in direction of arrow (C).

Fig. 1-2

(A)

(C)

(B)

Flap

Upper side

Bottom side

Remove the 4 screws (1).

Remove the Top Cabinet in the direction of arrow (A).

Disconnect the following connector: (CP651).

Unlock the 7 supports (2).

Remove the Front Cabinet in the direction of arrow (B).

Remove the 3 screws (3) and remove the Operation PCB.

Fig. 1-1

(2) (2)

(1)

(2)

(B)

(A)

(1)

Top Cabinet

(2)

(3)

Operation PCB

Front Cabinet

1-4: SYSCON PCB (Refer to Fig. 1-4)

Remove the 2 screws (1).

Remove the screw (2).

Remove the Syscon PCB in the direction of arrow (A).

Remove the Audio PCB in the direction of arrow (B).

Fig. 1-4

(2)

Audio PCB

Syscon PCB (1)

Bottom Plate

(1)

(B)

(A)

DISASSEMBLY INSTRUCTIONS

B2-1

2. REMOVAL OF VCR DECK PARTS

2-1: TOP BRACKET (Refer to Fig. 2-1)

Extend the 2 supports (1).

Slide the 2 supports (2) and remove the Top Bracket.

2-2: CASSETTE HOLDER ASS'Y (Refer to Fig. 2-2)

Move the Cassette Holder Ass'y to the front side.

Push the Locker R to remove the Cassette Side R.

Remove the Cassette Side L.

Fig. 2-1

Main Chassis

Top Bracket

Main Chassis

Cassette Side L

Cassette Side R Locker R

Fig. 2-2

2-3: CASSETTE SIDE L/R (Refer to Fig. 2-3-A)

Remove the Locker Spring.

Unlock the 4 supports (1) and then remove the

Cassette Side L/R.

Unlock the support (2) and then remove the Locker R.

Link Ass'y

NOTE

In case of the Locker R installation, check if the one

position of Fig.2-3-B is correctly locked.

When you install the Cassette Side R, be sure to move

the Locker R after installing.

2-4: LINK UNIT (Refer to Fig. 2-4)

Set the Link Unit to the Eject position.

Unlock the support (1).

Remove the (A) side of the Link Unit first, then remove

the (B) side.

Fig. 2-4

Fig. 2-3-A

Cassette Side L

Cassette Side R

Locker R

Cassette Holder

Locker Spring

Fig. 2-3-B

Check if this

position is locked.

(A)

Link Unit

Main Chassis

Link Unit

(B)

Main Chassis

Cassette Side R

Locker R

(1)

NOTE

1. After the installation of the Top Bracket, bend the

support (1) so that the Top Bracket is fixed.

(1)

(2)

(1)

2-5: LINK LEVER/FLAP LEVER/BOT COVER

(Refer to Fig. 2-5)

Fig. 2-5

Unlock the support (1).

Remove the BOT Cover.

Extend the support (2).

Remove the Link Lever.

Remove the Flap Lever.

LinkLever

FlapLever

(2)

(1) BOT Cover

DISASSEMBLY INSTRUCTIONS

B2-2

2-6: LOADING MOTOR/WORM (Refer to Fig. 2-6-A)

Remove the screw (1).

Remove the Loading Motor.

Remove the Worm.

Fig. 2-6-A

• Screw Torque: 3 ± 0.5kgf•cm

Loading Motor

(1)

Main Chassis

Worm

2-7: TENSION ASS'Y (Refer to Fig. 2-7-B)

Turn the Pinch Roller Cam clockwise so that the

Tension Holder hook is set to the position of Fig. 2-7-A

to move the Tension Arm Ass'y.

Remove the Tension Spring.

Unlock the 2 supports (1) and remove the Tension

Band.

Unlock the support (2) and remove the Tension Arm

Ass'y.

Unlock the support (3) and remove the Tension

Connect.

Float the hook (4) and turn it clockwise then remove

the Tension Holder.

NOTE

In case of the Worm installation, check if the value of

the Fig. 2-6-B is correct.

In case of the Loading Motor installation, hook the wire

on the Cassette Opener as shown Fig. 2-6-C.

When installing the wires between Capstan DD Unit

and Loading Motor, connect them correctly as shown

Fig. 2-6-D.

Loading Motor Capstan DD Unit

Pink

Fig. 2-6-D

White

Fig. 2-7-A

Tension Arm Ass'y

Fig. 2-7-B

Fig. 2-7-D

Tension Band

Tension Spring

(1)

(2)

(4)

Tension Band

Tension Arm Ass'y

(3)

(1)

Tension Holder

Tension Connect

NOTE

In case of the Tension Band installation, note the

direction of the installation. (Refer to Fig. 2-7-C)

In case of the Tension Band installation, install

correctly as Fig. 2-7-D.

In case of the Tension Connect installation, install as

the circled section of Fig. 2-7-E.

Tension Band

Tension Connect

[OK]

[NG]

Fig. 2-7-E

Tension Connect

Main Chassis

Fig. 2-7-C

Tension Band

Tension Connect

Fig. 2-6-B

19.2 ± 0.1mm

Safety surface for

pressing of the insert.

Fig. 2-6-C

Loading Motor

Cassette Opener

Table des matières

Autres manuels Schaub Lorenz Système de magnétoscope

Schaub Lorenz

Schaub Lorenz SL0014KO Manuel utilisateur

Schaub Lorenz

Schaub Lorenz SL0520KO Manuel utilisateur

Manuels Système de magnétoscope populaires d'autres marques

Toshiba

Toshiba M-662 Manuel utilisateur

Sony

Sony GV-500 Primary Manuel utilisateur

JVC

JVC HR-J282EU Manuel utilisateur

Sony

Sony HDCAM-SR SRW5800 Manuel utilisateur

Magnavox

Magnavox VRU242AT Manuel utilisateur

Sony

Sony HVR-M10C Manuel utilisateur

RCA

RCA VR634HF - Hi-Fi VCR Manuel utilisateur

JVC

JVC HR-5910U Manuel utilisateur

Panasonic

Panasonic ProLine AG-1320 Manuel utilisateur

JVC

JVC HR-S8600EU Manuel utilisateur

JVC

JVC HR-FS1U Manuel utilisateur

Sharp

Sharp VC-H9888U Manuel utilisateur

FUNAI

FUNAI LC-950 Manuel utilisateur

Sharp

Sharp VC-S2000GM Manuel utilisateur

Sony

Sony Video8 EV-A60 Manuel utilisateur

Panasonic

Panasonic Omnivision PV-V4523S Manuel utilisateur

Aiwa

Aiwa HV-E212 Manuel utilisateur

JVC

JVC HR-J3006UM Manuel utilisateur