Scandex SX-1134 Manuel utilisateur

USER GUIDE V2

SX-1134 433 MHZ LASER SCANNER

Characteristics...............................................................

Pairing Mode..................................................................

Functions.......................................................................

Working Mode................................................................

Character Codes Table....................................................

Performance Parameters.................................................

Operation Guide.............................................................

Number of Conceal Characters Table................................

Maintenance Record.......................................................

Prefix and Suffix.............................................................

Warranty........................................................................

Content..........................................................................

INDEX

Please take time to read this user guide before using the barcode scanner.

If you have any questions please contact us or alternatively support is available

via the “Scandex Red Card”enclosed in the box.

CHARACTERISTICS

Ergonomic design. External soft rubber bumpers and rugged internal build

for better and faster barcode reads. Easy to use with a simple setup. Large capacity,

superior to the average drop resistance. The latest barcode engine and decoding technology

Scanning setting alarm: A short beep. Low voltage alarm: A long beep.

greater than ordinary scanners ensures longer use after fully charged.

Pairing operation failure: 3 short beeps.

Data unloading success: 2 short beeps. Failure: 3 short beeps

SOUND GUIDE

FUNCTIONS

Automatic jumping frequency. Strong Anti-Interference ability.

Transmission distance with obstacles under ‘Normal Mode’

is 20m-100m and over 400m with no obstacles.

If the distance is exceeded 3 beeps will sound, indicating the data load has failed.

Each scanner has a unique mechanical ID to avoid interferences with other devices in use.

The customizable ID allows the user to distinguish the data source easily.

The pairing method is very simple. Repeated pairing is possible.

The ‘Check Mode’ is simple and easy to use. Can storage between

500-10000 barcode messages. (Customization is needed if messages are more then 500).

Automatic ‘Sleep Mode’. Sleeping current is less than 10UA,

this extends greatly the standby time of the battery.

A special charging circuit guarantees a safe charge.

To force a shutdown at any time hold the trigger for 12 seconds.

PAIRING MODE

INSTRUCTIONS

One to one

Connect the receiver into the computer USB interface.

The indicator on the cradle turns on while the drivers are being installed.

before the indicator on the scanner starts ﬂashing indicating the installation is complete.

The scanner is ready to be used.

One to one & storage

One to more More to one

Scan the code ‘One to One’ within 5 seconds,

One to One

One to One One to One Stored Data

One to One

Stored Data Upload

Stored Data Restore Breakpoint Continuingly

One to One

Stored Data Total Stored Data Reset

Clear All More to One Pairing

Clear All One to More Pairing

To clear previous pairing scan the code

‘Clear All One to More Pairing’ or ‘Clear All More to One Pairing’.

ID Settings Display ID Hide ID

ID PARAMETERS TABLE

ID SETTINGS

SLEEP MODE SETTINGS

8 hrs

None

5 min 10 min

2 min

30 sec

20 min

Sleep Mode Settings 20 sec 60 sec

By default the pre set time for the device to enter into ‘Sleep Mode’ is 20 seconds.

Recovery Routine Wireless Mode

Note: Do not read ‘Recovery Routine’ under ‘Common Mode’.

WORK STATUS

No Losing Mode Total Stored Data

No Losing Mode Clear Stored Data

Normal Mode No Losing Mode

and will be uploaded to the receiver when reaching the wireless transmission range.

WORKING MODE SETTINGS

Under the ‘No Losing Mode’, when exceeding the wireless transmission range the data will be stored

Check Mode

Checked Data Total

Checked Data Upload Checked Data Upload Checked Data Upload

Sound ON Sound OFF

Checked Data Clear

Checked Data Restore

‘Breakpoint’ for the remaining data to be uploaded.

If the scanner losses connection during the upload process read the code

Breakpoint

Table des matières

Autres manuels Scandex Lecteur de codes-barres

Scandex

Scandex SX-1141 Manuel utilisateur

Manuels Lecteur de codes-barres populaires d'autres marques

POSMicro

POSMicro Datalogic PowerScan D7100 Manuel utilisateur

Marson

Marson MT780 Guide de configuration rapide

NCR

NCR RealPOS Manuel utilisateur

Motorola

Motorola SE3300 Guide de configuration rapide

Element

Element P130BT Manuel utilisateur

Motorola

Motorola Symbol LS3008 Manuel d'installation et d'exploitation

Meec tools

Meec tools OBD-II / VAG Manuel utilisateur

SICK

SICK CLP 100 Manuel utilisateur

Royal Tag SA

Royal Tag SA I-Read Manuel utilisateur

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuel utilisateur

Meteor

Meteor 8310 Manuel utilisateur

Denso

Denso BHT-500B Manuel utilisateur

Datalogic

Datalogic Heron HD3130 Manuel utilisateur

Motorola

Motorola MP6000 Instructions de montage

Newland

Newland NLS-HR15-BT Manuel utilisateur

ARTDEV

ARTDEV AS-1310 Manuel utilisateur

Aopos

Aopos AS290 Manuel utilisateur

ENS

ENS 367-5455 Manuel utilisateur