Savant SEN-OCC24V Series Manuel utilisateur
Occupancy Sensor 24V Contact QRG | 009-1919-02 45 Perseverance Way, Hyannis, MA 02601
Copyright 2021 Savant Systems, Inc | 210312 1 of 4 Savant.com | 508.683.2500
Box Contents
(1) Occupancy Sensor 24V Contact (SEN-OCC24V-xx)
(1) Wall Anchor Kit
(2) Retaining Springs
(1) Quick Reference Guide (this document)
Specifications
Environmental
Indoor Use Only
Temperature 32° to 104° F (0° to 40°C)
Humidity 10% to 90% (non-condensing)
Dimensions and Weights
Height 1.5 in (38.1 in)
Diameter 3.75 in (95.25 mm)
Weight 0.20 lbs ( 0.09 kg)
Power
Input 24V DC
Power
Consumption 5 - 20 mA
Regulatory
Safety and
Emissions
FCC Part 15 CE C-Tick
RoHS Compliant
Drop Ceiling Installation
1. Install the two retaining springs.
2. Use a hole saw to cut a circular hole (85mm) in the drop ceiling
panel.
3. Holding the retaining springs together, push assembled sensor
through ceiling panel hole until sensor seam is seated flush.
Occupancy Sensor 24V Contact Quick Reference Guide
Top Panel Bottom Panel
Relay 24V
+
-
SEN-OCC24V-00 REV: XX
OCCUPANCY SENSOR
INPUT: 24V DC
OUTPUT: RELAY (NO)
MADE IN CHINA
A
ON OFF ON OFF
12 3 4
ON DIP
B
12 3 4
ON DIP
A B CDF G
H I J
E
K
ARelay Normally Open (NO) solid state relay
Maximum: 50 mA / 30V
BPower Input 24 V DC.
CUltrasound Sensor Used to detect motion.
DDip Switch A Refer to Sensor Modes.
E
Ultrasound
Sensitivity
Adjustment
Adjust Ultrasound sensitivity level. Refer to
Occupancy Sensor Adjustment.
FPIR Sensor Uses Infrared to detect motion.
G
Ambient
Sensitivity
Adjustment
Adjust sensitivity of motion detection with
only ambient lighting. Refer to Occupancy
Sensor Adjustment.
H
PIR Sensitivity
Adjustment
Set the tolerance for microphones to
detect sound and activate relays. Refer to
Occupancy Sensor Adjustment.
IAmbient Light
Sensor
Set the range at which infrared sensor will
.detect movement and activate lights
J
Timer Adjustment
Set the length of time relays remain
active after occupancy detection. Refer to
Occupancy Sensor Adjustment.
KDip Switch B Refer to Sensor Modes.
Solid Ceiling Installation
1. Attach base ring to the ceiling with included screws.
2. Press sensor onto base ring.
2
3
1
2
1
Occupancy Sensor 24V Contact QRG | 009-1919-02 45 Perseverance Way, Hyannis, MA 02601
Copyright 2021 Savant Systems, Inc | 210312 2 of 4 Savant.com | 508.683.2500
Occupancy Sensor Adjustment
Remove the control cover to adjust occupancy sensor settings. Refer to the diagram and table below for details:
Timer Adjustment 30 Seconds 5 minutes 10 minutes 20 Minutes 30 Minutes
Ambient Light
Sensitivity 20 Lux 40 Lux 80 Lux 160 Lux 320 Lux
Ultrasound Range
O Low Medium High Maximum
Infrared Range
Sensor Modes
The Occupancy / Motion Sensor can be configured to meet the requirements of the deployment. To do this, remove the sensor cover and
configure the DIP Switch banks as described below.
Switch O On
A
ON OFF ON OFF
12 3 4
ON DIP
B
12 3 4
ON DIP
A1 Multi-Tech Mode Single Tech Mode
A2 PIR Mode Ultrasonic Mode
A3 Auto-Adapting Enabled Auto-Adapting Disabled
A4 Walk-Through Enabled Walk-Through Disabled
B1 Light Mode Enabled Light Mode Disabled
B2 LEDs Enabled LEDs Disabled
B3 OFF > ON > OFF: Enter/Exit Test Mode
B4 N/A
Multi-Tech Mode 1: (A1 OFF, A2 ON) If motion is detected in PIR or Ultrasonic, the relay is closed.
Multi-Tech Mode 2: (A1 OFF, A2 OFF) If motion is detected by the PIR, both PIR and Ultrasonic sensors will be activated. If motion is detected
by either in this state, the relay is closed.
Single-PIR Mode: (A1 ON, A2 OFF) If motion is detected by PIR Sensor, the relay is closed.
Single-Ultrasonic Mode: (A1 ON, A2 ON) If motion is detected by Ultrasonic sensor, the relay is closed.
Auto-Adapting Mode: When room lights are turned on, sensor enters the Walk-Through mode. If occupancy is detected for longer than 2.5
minutes, the occupancy sensor will exit Walk-Through mode and treat the room as occupied. The length of time.
Walk-Through Mode: Lights will be turned o shortly after no occupancy is detected.
Light Mode: Ambient Light sensing is enabled.
Timer Mode: The output signal to attached relays will last 2.5 minutes when this mode is enabled. If occupancy is sensed during this time, the
relay will be closed.
Test Mode: Sets the Delayed-O Time Adjustment to 5 seconds. This mode will persist for 15 minutes or until the OFF-ON-OFF command
sequence is entered again.
Occupancy Sensor 24V Contact QRG | 009-1919-02 45 Perseverance Way, Hyannis, MA 02601
Copyright 2021 Savant Systems, Inc | 210312 3 of 4 Savant.com | 508.683.2500
Example Wiring Diagram
NOTE: The Low Voltage Keypad diagram below shows the Occupancy/Motion sensor wired to a Low Voltage Keypad. However it can be wired to
any GPIO Port.
Basic Deployment
5 VDC
-GPIO/Relay
1CG
PD
NC
NO
Relay 24V
+
-
Savant Controller
To Power Supply NOTES:
–This works with any Savant Controller using a sense GPIO.
–An external power supply is required.
Savant Keypad Link w/External Power
Relay 24V
+
-
T
o Keypad Link
To Power Supply
NOTE: An external power supply is required.
Savant Keypad Link
Relay 24V
+
-
To Keypad Link
NOTES:
–All Savant Keypad Links have a maximum number of keypads
per run, the occupancy sensor counts as a keypad in this
maximum when being powered by an SKL.
Occupancy Sensor 24V Contact QRG | 009-1919-02 45 Perseverance Way, Hyannis, MA 02601
Copyright 2021 Savant Systems, Inc | 210312 4 of 4 Savant.com | 508.683.2500
NOTES:
Ce manuel convient aux modèles suivants
1
Autres manuels Savant Capteur de sécurité
