Savant SmartControl SSC-W02R Manuel utilisateur
SSC-W02R Quick Reference Guide | 009-1373-04 45 Perseverance Way, Hyannis, MA 02601
Copyright © 2021 Savant Systems, Inc. | 210628 1 of 2 Savant.com | 508.683.2500
Box Contents
(1) SmartControl RS232 Controller (SSC-W02R)
(1) Installation Kit (075-0174-xx)
(1) Mounting Plate (074-0569-xx)
(1) 6-pin Screw Down Plug-in Connector (028-9352-xx)
(1) 5V DC 1.2A Power Supply (025-0207-xx)
(1) Cable Tie (014-0071-xx)
(1) Product and Regulatory Insert (009-1950-xx)
Specifications
Environmental
Temperature 32° to 104° F (0° to 40°C)
Humidity 10% to 90% (non-condensing)
Dimensions and Weights
Height Width Depth Weight
Device 0.64 in
(1.62 cm)
2.70 in
(6.85 cm)
2.67 in
(6.78 cm)
0.50 lbs
(0.22 kg)
Shipping 3 in
(7.62 cm)
7 in
(17.78 cm)
10 in
(25.40 cm)
2.0 lbs
(0.90 kg)
Power
Input 5V DC 1.2A
Maximum 6 watts
Standards
Wireless
Wi-Fi (802.11 b/g/n 2.4 GHz)
IMPORTANT! 802.11r (fast roaming) is not
supported.
Security WPA™, WPA2™, WPA/WPA2™, WEP
Savant® SmartControl RS232 Wi-Fi Controller (SSC-W02R)
Quick Reference Guide
Network Guidelines
For more information, see the Savant Device Networking Guidelines
on the Savant Customer Community.
Front Panel
A
Press and hold for five seconds while powered On to clear the
network settings. The Status LED blinks rapidly when reset is
complete.
B
O: No Power
On Solid: Provisioned to the local network and communicating
with the Savant System Host.
Blinks Once: In Provisioning Mode. Ready to be added to the
local network.
1s.5s
REPEAT
Blinks Twice: Establishing connection with the local network.
.5s.5s .5s
REPEAT
1s
Blinks Three Times: Connected to the local network. Is
connecting to the Host.
.5s .5s.5s .5s
REPEAT
.5s 1s
Short O Blink: Firmware is updating.
.5s1.5s
REPEAT
Rapid Blink: The reset button was held down for at least five
seconds and the SSC-W02R is performing a factory reset. After
reset, all network settings are cleared and the factory defaults
are set.
.1s.1s .1s
REPEAT
.1s
Regulatory
Safety and
Emissions
FCC Part 15 CE C-Tick UKCA
Contains FCC ID: TLZ-CU277
Contains IC: 6100A-CU277
RoHS Compliant
Minimum Supported Release
Savant OS da Vinci 8.2
SSC-W02R Quick Reference Guide | 009-1373-04 45 Perseverance Way, Hyannis, MA 02601
Copyright © 2021 Savant Systems, Inc. | 210628 2 of 2 Savant.com | 508.683.2500
Rear Panel
CD
AB
5 VDC
-RS232
1
G
Tx
Rx
G
Tx
Rx
2
RS-232 Port 1 - 6-Pin Plug-In Connector (Left 3 Pins)
A
G Signal Ground
Tx Transmit Data
Rx Receive Data
RS-232 Port 2 - 6-Pin Plug-In Connector (Right 3 Pins)
B
G Signal Ground
Tx Transmit Data
Rx Receive Data
C
Input Power 5V DC 1.2A. Connect to included power supply.
D
Cable Lance Use with included cable tie to secure power
supply connection.
RS-232 Wiring and Connections
A 6-pin screw down type connector is included with each SSC-W02R
controller. This connector plugs into the connection on the rear of the
controller.
4 5 632
1
PIN 1 GND
PIN 2 TxD
PIN 3 RxD
PIN 4 GND
PIN 5 TxD
PIN 6 RxD
G
Tx Rx
G
Tx Rx
1. Remove power if applied.
2. Pull to remove the terminal block from the rear of the controller.
3. With a small flat bladed screwdriver,
turn the screws on top of the
connector counterclockwise until
the silver crimps in the rear of the
connector open enough to slide the
wire(s) into the square slots.
4. Strip back the insulation on each of
the wires ¼ inch. Insert the stripped
wires into their proper ports. Do not
allow more than ⅛ inch of bare wire
exposed.
5. Turn the screws on the top of the connector clockwise until the
crimps tighten around each wire. Tug on each wire a bit to verify
they are installed securely.
6. Plug terminal block back into the rear of the controller.
7. Reapply power.
< 1/8 inch
bare wire
exposed
Connecting to a Wireless Network
Refer to the SmartControl RS232 – Wi-Fi Smart Controller with 2
RS232 Deployment Guide located on the Savant Customer Community
to connect the SSC-W02R to the local network.
Additional Documentation
Additional Documentation is available on the Savant Customer
Community.
–SmartControl RS232 - Wi-Fi Smart Controller with 2 RS232 (009-
1374) Deployment Guide
–RS-232 Conversion to DB-9 and RS-422/485 Pinout Reference
Guide
Autres manuels Savant Contrôleurs
Savant
Savant SmartControl 3 Guide de référence rapide
Savant
Savant SmartControl Manuel utilisateur
Savant
Savant ICC-TP00 Manuel utilisateur
Savant
Savant LCB-DMX1 Guide de référence rapide
Savant
Savant S2 Manuel utilisateur
Savant
Savant SmartControl 25 Manuel utilisateur
Savant
Savant SmartControl 3 Manuel utilisateur
Savant
Savant SmartLighting 18 Manuel utilisateur
Savant
Savant Lamp Controller Manuel utilisateur
Savant
Savant QO PBC-1000-10 Guide de référence rapide
Savant
Savant CPT-1212 Manuel utilisateur
Savant
Savant Pro Host Manuel utilisateur
Savant
Savant Director HST-DIRECTOR Manuel utilisateur
Savant
Savant SmartControl 3 Manuel utilisateur
Savant
Savant SmartControl 7 Manuel utilisateur
Savant
Savant SmartLighting SSL-W002 Manuel utilisateur
Savant
Savant FRC-P100-00 Manuel utilisateur
Savant
Savant SmartControl 3 Manuel utilisateur
Savant
Savant WIF 104 Series Manuel utilisateur
Savant
Savant SmartLighting 2 Manuel utilisateur
