Satel FD-1 Manuel utilisateur

FD-1

WATER FLOOD DETECTOR

fd1_en 09/17

The FD-1 detector senses the presence of water leaks or flooding in rooms with plumbing.

This manual applies to the detector with electronics version 1.4 (or newer).

1. Features

External flood sensor.

Supply voltage control.

LED indicator.

Tamper protection against cover removal and tearing enclosure from the wall.

2. Description

The alarm is triggered approximately 4 seconds after the water level

reaches the height at which the flood sensor electrodes are installed.

During the alarm condition the relay contacts are open and the LED

is ON. The alarm ends a few seconds after the water level drops

below the height at which the flood sensor electrodes are installed.

Supply voltage control

In the event of a prolonged voltage drop below 9 V (±5%), the

detector will signal a trouble. The trouble is indicated by the

activation of alarm relay and the steady light of LED indicator. The

trouble signaling will continue as long as the trouble persists.

Electronics board

terminals:

+12V - power input.

COM - common ground.

TMP - tamper output (NC).

NC - alarm output (NC relay).

tamper contact.

LED indicating the relay status. It lights red when the relay is

open.

pins for enabling/disabling the LED indicator. The LED indicator

is enabled when jumper is placed on the pins.

terminals for the flood sensor connection.

3. Installation

Disconnect power before making any electrical connections.

The detector is designed for indoor operation.

1. Select the place where the detector is to be installed.

2. Open the detector enclosure (Fig. 2).

3. Make the wire entry opening in the enclosure base.

4. Run the wires through the opening made.

2 FD-1 SATEL

5. Pull the flood sensor wires through the hole in the enclosure.

6. Use screws to fix the enclosure base to the mounting surface (Fig. 4). Wall plugs (screw

anchors) and screws are included in the detector delivery set.

7. Connect the wires to the detector terminals.

8. Close the detector enclosure.

9. Test the detector for proper operation, by submerging the flood sensor in water.

10.Secure the flood sensor wires and the flood sensor itself (Fig. 5). The detector is now

ready for work.

4. Specifications

Supply voltage .................................................................................................12 V DC (±15%)

Standby current consumption ........................................................................................ 2.5 mA

Maximum current consumption ......................................................................................... 4 mA

Relay contacts rating (resistive load) .............................................................. 40 mA / 16 V DC

Flood sensor cable length....................................................................................................3 m

Environmental class.................................................................................................................II

Operating temperature range.............................................................................-10 °C...+55 °C

Enclosure dimensions................................................................................... 26 x 112 x 29 mm

Weight.................................................................................................................................81 g

The declaration of conformity may be consulted at www.satel.eu/ce

SATEL sp. z o.o. • ul. Budowlanych 66 • 80-298 Gdańsk • POLAND

tel. +48 58 320 94 00

www.satel.eu

Table des matières

Autres manuels Satel Capteur de sécurité

Satel

Satel OPAL Manuel utilisateur

Satel

Satel PDB-100 Manuel utilisateur

Satel

Satel SLIM-DUAL-PRO Manuel utilisateur

Satel

Satel OPAL Plus Manuel utilisateur

Satel

Satel AOCD-260 Manuel utilisateur

Satel

Satel AOD-210 Manuel utilisateur

Satel

Satel AMD-103 Manuel utilisateur

Satel

Satel AOD-200 Manuel utilisateur

Satel

Satel MAGENTA Manuel utilisateur

Satel

Satel AQUA RING S Manuel utilisateur

Satel

Satel AMD-102 Manuel utilisateur

Satel

Satel OPAL Pro Manuel utilisateur

Satel

Satel abax 2 ACD-220 Manuel utilisateur

Satel

Satel ASD-250 Manuel utilisateur

Satel

Satel COBALT Manuel utilisateur

Satel

Satel OPAL Pro Manuel utilisateur

Satel

Satel MAGENTA Manuel utilisateur

Satel

Satel AGD-200 Manuel utilisateur

Satel

Satel APMD-150 Manuel utilisateur

Satel

Satel AQUA S Manuel utilisateur

Satel

Satel AGATE Manuel utilisateur

Satel

Satel micra MXD-300 Manuel utilisateur

Satel

Satel CD-2 Manuel utilisateur

Satel

Satel IVORY Manuel utilisateur

Manuels Capteur de sécurité populaires d'autres marques

THORLABS

THORLABS PDA10JT Manuel utilisateur

Waeco

Waeco UV-DETECT Manuel utilisateur

Intermatic

Intermatic IOS-DSIMF Manuel utilisateur

urmet domus

urmet domus 1083 Manuel utilisateur

Siemens

Siemens AZL66 Series Manuel utilisateur

BTI

BTI Profiline Multi Finder Manuel utilisateur

Challenger

Challenger SL01 Manuel utilisateur

DMP Electronics

DMP Electronics 1122INT Manuel utilisateur

Rielta

Rielta Ladoga MK-RK Manuel utilisateur

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuel utilisateur

Bosch

Bosch DS835 Manuel utilisateur

DBI SALA

DBI SALA EZ Stop Manuel de l'opérateur

Lamptime

Lamptime ST05C Manuel utilisateur

Ubiquiti

Ubiquiti MFI-MSC Manuel utilisateur

Subsite

Subsite 910R Instructions d'installation

Aleph

Aleph XC-1XTEU Manuel utilisateur

Pima

Pima LARIS QUAD Manuel utilisateur

Solinst

Solinst 301 Manuel utilisateur