Sanyo FVM4612 Manuel utilisateur

1

Service Manual

LCD TV

Model No. Service Reference No.

FVM4612

DP46132

DP46132M

WARNING

This service information is designed for experienced repair technicians only and is not designed for use by the general public. It does not

contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. Products powered by

electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair the product or

products dealt with in this service information by anyone else could result in serious injury or death.

There are special components used in this equipment which are important for safety. These are marked by in the Schematic Diagrams,

Circuit Board Diagrams. Exploded Views and Replacement Parts List. It is essential that these critical parts should be replaced with

manufacture’s specified parts to prevent shock, fire or other hazards. Do not modify the original design without permission of manufacturer.

IMPORTANT SAFETY NOTICE

Sanyo Manufacturing Corp. 3333

Sanyo Road, Forrest City, AR 72335

Printed in China, Dec, 2012

P46142-03

P46142-04

P46142M-04

All manuals and user guides at all-guides.com

all-guides.com

2

TABLEOFCONTENTS Page

1 Safety Precaution ------------------------------------------------------------------------------------------------ 3

1.1. General Guidelines ---------------------------------------------------------------------------------------- 3

2 Warning ------------------------------------------------------------------------------------------------------------- 4

2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive(ES) Devices 4

2.2. About lead free solder (PbF) ---------------------------------------------------------------------------- 5

3 Service Navigation----------------------------------------------------------------------------------------------- 6

3.1. Service Hint-------------------------------------------------------------------------------------------------- 6

3.2. Applicable signals------------------------------------------------------------------------------------------ 7

4 Specifications ----------------------------------------------------------------------------------------------------- 8

5 Troubleshooting Guide----------------------------------------------------------------------------------------- 9

5.1 No Power ----------------------------------------------------------------------------------------------------- 9

5.2 Abnormal Display ------------------------------------------------------------------------------------------10

5.3 No Display ---------------------------------------------------------------------------------------------------11

5.4 Sound Problem ---------------------------------------------------------------------------------------------12

5.5 Remote Control Malfunction ----------------------------------------------------------------------------13

6 Disassembly and Assembly Instructions ---------------------------------------------------------------14

7 Block Diagram----------------------------------------------------------------------------------------------------18

8 Schematic Diagram---------------------------------------------------------------------------------------------19

8.1 Main Board --------------------------------------------------------------------------------------------------19

8.2 Power Board ------------------------------------------------------------------------------------------------29

8.3 Key Board----------------------------------------------------------------------------------------------------32

8.4 IR Board------------------------------------------------------------------------------------------------------33

9 Wiring Connection Diagram ---------------------------------------------------------------------------------34

9.1. Caution Statement --------------------------------------------------------------------------------------34

9.2. Wiring --------------------------------------------------------------------------------------------------------34

10 Exploded View and Replacement Parts List----------------------------------------------------------35

10.1. Exploded View ------------------------------------------------------------------------------------------35

10.2. Replacement Parts List --------------------------------------------------------------------------------36

All manuals and user guides at all-guides.com

3

1 Safety Precautions

1.1. General Guidelines

1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been

overheated or damaged by the short circuit.

2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are

properly installed.

3. After servicing, make the following leakage current checks to prevent the customer from being exposed to

shock hazards.

4. When conducting repairs and servicing, do not attempt to modify the equipment, its parts or its materials.

5. When wiring units (with cables, flexible cables or lead wires) are supplied as repair parts and only one wire or

some of the wires have been broken or disconnected, do not attempt to repair or re-wire the units. Replace the

entire wiring unit instead.

6. When conducting repairs and servicing, do not twist the Faston connectors but plug them straight in or unplug

them straight out.

1.1.1. Leakage Current Cold Check

1. Unplug the AC cord and connect a jumper between

the two prongs on the plug.

2. Measure the resistance value, with an ohmmeter,

between the jumpered AC plug and each exposed

metallic cabinet part on the equipment such as

screw heads, connectors, control shafts, etc.

When the exposed metallic part has a return path

to the chassis, the reading should be 100 Mohm

and over. When the exposed metal does not have

a return path to the chassis, the reading must be

1.1.2. Leakage Current Hot Check (See Figure 1.)

1. Plug the AC cord directly into the AC outlet. Do

not use an isolation transformer for this check.

2. Connect a 1.5kohm, 10 watts resistor, in parallel

with 0.15μF capacitors, between each exposed

metallic part on the set and a good earth ground

such as a water pipe, as shown in Figure 1.

3. Use an AC voltmeter, with 1000 ohms/volt or

more sensitivity, to measure the potential

across the resistor.

4. Check each exposed metallic part, and

measure the voltage at each point.

5. Reverse the AC plug in the AC outlet and

repeat each of the above measurements.

6. The potential at any point should not exceed

0.75 volts RMS. A leakage current tester

(Simpson Model 229 or equivalent) may be

used to make the hot checks, leakage current

must not exceed 1/2 milliamp. In case a

measurement is outside of the limits specified,

there is a possibility of a shock hazard, and the

equipment should be repaired and rechecked

before it is returned to the customer.

Figure 1

All manuals and user guides at all-guides.com

4

2 Warning

2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly

are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some

field-effect transistors and semiconductor [chip] components. The following techniques should be used to help

reduce the incidence of component damage caused by electrostatic discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off

any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially

available discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying

power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface

such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static solder removal device. Some solder removal devices not classified as [anti-static (ESD

protected)] can generate electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to

install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive

foam, aluminum foil or comparable conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the

protective material to the chassis or circuit assembly into which the device will be installed.

Caution

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise ham less motion

such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate

static electricity (ESD) sufficient to damage an ES device).

All manuals and user guides at all-guides.com

5

2.2. About lead free solder (PbF)

Note: Lead is listed as (Pb) in the periodic table of elements.

In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder.

The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu).

That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.

This model uses Pb Free solder in it’s manufacture due to environmental conservation issues. For service and repair

work, we’d suggest the use of Pb free solder as well, although Pb solder may be used.

PCBs manufactured using lead free solder will have the PbF within a leaf Symbol PbF stamped on the back of PCB.

Caution

• Pb free solder has a higher melting point than standard solder. Typically the melting point is 50 ~ 70 °F

(30~40 °C) higher. Please use a high temperature soldering iron and set it to 700 ± 20 °F (370 ± 10 °C).

• Pb free solder will tend to splash when heated too high (about 1100 °F or 600 °C).

If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before

applying Pb solder.If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder.

• After applying PbF solder to double layered boards, please check the component side for excess solder which

may flow onto the opposite side. (see figure below)

Suggested Pb free solder

There are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper)

solder. However, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used.

All manuals and user guides at all-guides.com

6

3 Service Navigation

3.1 Service Hint

Board Name Function Remarks

Main Board

SPDIF,COMPONENT/AV IN, ANTENNA/DTV/TV,

PC IN,PC/DVI IN/AUDIO,

HDMI(HDMI1/DVI,HDMI2,HDMI3),USB PORT All boards are non

serviceable and should

be exchanged for service

IR Board Remote Receiver, LED

Power Board Power (AC/DC), DC-DC

Key Board Control Button, Power switch

Main Board

Power Board

Key Board

IR Board

All manuals and user guides at all-guides.com

all-guides.com

7

3.2. Applicable signals

Resolution VGA HDMI-DVI Component Horizontal

Freq. (KHz) Vertical Freq.

(Hz) Nominal Pixel

Clock (MHz)

640x480@60Hz ●●31.469 59.940 25.175

720x400@70Hz ●●31.469 70.087 28.322

800x600@60Hz ●●37.879 60.317 40.000

1024x768@60Hz ●●48.363 60.004 65.000

1280x720@60Hz ●●44.772 59.855 74.500

1280x768@60Hz ●●47.396 59.995 68.250

1280x1024@60Hz ●●63.981 60.020 108.000

1440x900@60Hz ●●55.469 59.901 88.750

1680x1050@60Hz ●●65.290 59.954 146.250

720x480i 59.94/60Hz ●●

720x480P 59.94/60Hz ●●

720P 59.94/60Hz ●●

1080i 59.94/ 60Hz ●●

1080P 24Hz ●

1920x1080@60Hz ●●67.500 60.000 148.500

All manuals and user guides at all-guides.com

8

4 Specifications

Panel Type • LCD

Panel Size • 46"

Maximum Visible Range • 1018.08(H)× 572.67(V)

Refresh Rate • 60 Hz

Picture Resolution • Full HD (1920x1080)

Viewing Angle • 178°(H), 178°(V)

Brightness • 350 cd/m

Contrast Ratio • 3000:1 (Typical)

Voltage • AC120V~ 60 Hz

Power Consumption • 98 Watts

Color System • NTSC, ATSC, Clear QAM

Channel Coverage

• Low band: 55.25 to 144.00MHz

• Mid band: 145.00 to 424.00MHz

• High band: 425.00 to 861.00MHz

Horizontal frequency • 30 ~ 80 KHz

Vertical frequency • 56 ~ 75 Hz

Inputs/Outputs

• DIGITAL AUDIO OUT (S/PDIF)

• COMPONENT/AV IN

• ANTENNA/DTV/TV

• PC IN (D-Sub)

• PC/DVI (AUDIO IN)

• HDMI (HDMI1/DVI, HDMI2, or HDMI3)

• USB

Audio Output • 8W + 8W

Dimensions (Including

Stand) • 1056.2(L) x 214.9(W) x 673.3(H) mm

Net Weight (Including

Stand) • 15.8 kg

Operating Environment

• Operating Temperature: 0°C to 35°C

• Operating Humidity: 10 % to 90 % (non-condensing)

• Storage Temperature: -20°C to 60°C

• Storage Humidity: 30% to 90% (non-condensing)

• Specifications are subject to change without notice.

All manuals and user guides at all-guides.com

9

5. Troubleshooting Guide

5.1 No Power

No power (LED “Off”)

Check the AC input and

the power is “ON”? Power “On”

Power board

output=5.2V?

Replace the Power board

Yes

Use RC or Key to turn on

the TV

Yes 1. RC can turn on the TV and Key can’t,

replace the key board.

2. Key can turn on the TV and RC can’t,

replace the RC.

Replace the Main board

All manuals and user guides at all-guides.com

10

5.2 Abnormal Display



Abnormal Display

Replace LVDS Cable

Replace the main board

Replace the panel

Yes

Enter factory mode

to Reset

Replace the main board

Yes

Rese

Check the OSD is

normal?

All manuals and user guides at all-guides.com

Autres manuels pour FVM4612

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Sanyo TV

Sanyo

Sanyo DS19500 Manuel utilisateur

Sanyo

Sanyo C29LF39 Manuel utilisateur

Sanyo

Sanyo 29-F5BA Manuel utilisateur

Sanyo

Sanyo DP42840 - 42" Diagonal LCD FULL HDTV 1080p Manuel utilisateur

Sanyo

Sanyo C20LB18S Manuel utilisateur

Sanyo

Sanyo C29LF37 Manuel utilisateur

Sanyo

Sanyo CZP1662 Manuel utilisateur

Sanyo

Sanyo DS19500 Manuel utilisateur

Sanyo

Sanyo C29ZK80TX Manuel utilisateur

Sanyo

Sanyo LCD-46XZ10FH Manuel utilisateur

Sanyo

Sanyo CE21DN6F-C Manuel utilisateur

Sanyo

Sanyo DS35224 Manuel utilisateur

Sanyo

Sanyo CPP2910 Manuel utilisateur

Sanyo

Sanyo C1 4ZA25 Manuel utilisateur

Sanyo

Sanyo CA21XS2 Manuel utilisateur

Sanyo

Sanyo DP15647 Manuel utilisateur

Sanyo

Sanyo DP32648 - 31.5" LCD TV Manuel utilisateur

Sanyo

Sanyo CP20SR1 Manuel utilisateur

Sanyo

Sanyo CE 25MT2A-C Manuel utilisateur

Sanyo

Sanyo CW21CF1 Manuel utilisateur

Sanyo

Sanyo CT21MF2v Manuel utilisateur

Sanyo

Sanyo CP21G1 Manuel utilisateur

Sanyo

Sanyo CPP2940TX Manuel utilisateur

Sanyo

Sanyo CP34ST3T Manuel utilisateur

Manuels TV populaires d'autres marques

Philips

Philips Colour Television Manuel utilisateur

Toshiba

Toshiba 27A10 Manuel utilisateur

Philips

Philips 42PF9630A/37 Manuel utilisateur

Hitachi

Hitachi 32FX48B Manuel utilisateur

DAEWOO ELECTRONICS

DAEWOO ELECTRONICS DTQ-14V1FC Manuel utilisateur

Changhong Electric

Changhong Electric uhd55b6000is Manuel utilisateur

Philips

Philips Matchline 21CE7551 Manuel utilisateur

Panasonic

Panasonic Genus TX-G10 Manuel utilisateur

Toshiba

Toshiba 19A20 Manuel utilisateur

Philips

Philips 25PT4523-16 Manuel utilisateur

Sony

Sony XBR-100Z9D Manuel utilisateur

Philips

Philips PR0930X3 Manuel utilisateur

Philips

Philips Brilliance 231P4QPY Manuel utilisateur

Samsung

Samsung 55S9 B Series Manuel utilisateur

Philips

Philips 32HF9385D Guide de dépannage

Sharp

Sharp LC-40FI5012E Manuel utilisateur

Loewe

Loewe Table Stand Reference 55 Manuel utilisateur

Philips

Philips 32PFH5300 Manuel utilisateur