Sanyo CM29FS2 Manuel utilisateur

CM29FS2

CM29FS2A

CA29FS2

CP29FS2

INSTRUCTION MANUAL

Colour Television

■ Slim Flat Screen

■ A2 & Digital NICAM Stereo

■ Surround Sound System

■ Video Component Input Terminal

Inst. Manual C8ZRL-A (ME) 12/7/05 3:48 PM Page 1

Warnings and Cautions

If the television is to be built into a compartment or

similarly enclosed, the minimum distances must

be maintained. Heat build-up can reduce the ser-

vice life of your television, and can also be dan-

gerous.

Never stand on, lean on or push suddenly the tele-

vision or its stand.

You should pay special attention to children.

Serious injury may result if it should fall.

Do not place your television on an unstable cart,

stand, shelf or table. Serious injury to an individual,

and damage to the television, may result if it

should fall.

When the television receiver is not used for an

extended period of time, it is advisable to discon-

nect the AC power cord from the AC outlet.

Avoid exposing the television receiver to direct

sunlight and other source of the heat.

Do not stand the television receiver directly on

other products which give off heat. E.g. video cas-

sette players, audio amplifiers.

Do not block the ventilation holes in the back

cover.

Adequate ventilation is essential to prevent failure

of electrical components.

Do not squash power supply cord under the televi-

sion receiver.

Warning

High voltages are used in the operation of this

television receiver. Do not remove the cabinet

back from your set. Refer servicing to qualified

service personnel.

To prevent fire or electrical shock hazard, do

not expose the television receiver to rain or

moisture.

Do not drop or push objects into the television

cabinet slots or openings. Never spill any kind

of liquid on the television receiver.

Caution

Warning

Caution

5cm

10cm

20cm

Minimum distances

Caution

Inst. Manual C8ZRL-A (ME) 12/7/05 3:48 PM Page 2

Installation

■Plug & Play

■Connecting the aerial

Use one of these methods to connect a signal to your TV.

Following connection examples are our recommended standard connection. For further information please

consult your local dealer.

✐For all aerial circuit problems please consult your local dealer.

■Connecting AC cord

Connect the power cord of the TV set to a wall outlet.

✐The TV set is prepared for a mains voltage AC110~240V 50/60Hz. When the TV set is not to be used

for an extended period of time, it is advisable to disconnect the power cord from the power outlet.

WARNING!

High voltages are used in the operation of this set. Refer service to qualified service

personnel.

YCB

MONITOR

OUT

S-WOOFER

OUT

AV1 INPUT

AUDIO

S-VIDEO

(MONO)

AUDIO

S-WOOFER

VIDEO

AV3 / DVD

INPUT

Let’s start !

2Press the MENU button after completing Plug & Play to return to the normal TV mode.

This TV set provides a self-automatic tuning system function called “Plug & Play”. It automatically begins

searching and storing of all available channels when switching-on the TV set for the first time.

1Press the Power ON/OFF button to turn the TV on, and the TV set will search and store of all

available TV channels automatically.

✐ This procedure only appears at the first switch-on time.

Now the installation is completed !

STEP 1

STEP 2

STEP 3

Inst. Manual C8ZRL-A (ME) 12/7/05 3:48 PM Page 3

Control Panel Each button on the control panel has the same function

with its counterpart on the remote control

AUDIO

VIDEO

TV/AV MENU CH

Mains ON/OFF button

Remote Control Detector

Stand-by and Power Indicator

Audio Input Jack-Right (AV2)

Audio Input Jack-Left (AV2)

Video Input Jack (AV2)

Headphone Jack (Mini

Stereo Jack)

VOLUME

TV/AV Selector

Programme UP/DOWN

Press to open

Inst. Manual C8ZRL-A (ME) 12/7/05 3:48 PM Page 4

Remote Control

-/- -

BASS TXT/TV S. SYS

SURROUND

A•B

PICTURE

SWAP SOUND

TIMER

JXPSB

TV / AV

TV/AV Selector Button

RECALL/Colour System button

NUMERIC buttons

DIGIT button

SWAP button

VOLUME (-) button

STEREO/MONO button

PROGRAMME DOWN button

POWER ON/OFF button

Sound MUTE button

TIMER button

ALTERNATE button

SOUND Mode button

PROGRAMME UP button

VOLUME (+) button

MENU button

SURROUND button

To Install Batteries Into the Remote Control

1. Remove the battery compartment cover.

2. Insert two size AA batteries (1.5 V) according to "+" and "-" polarity markings inside the battery

compartment.

3. Close the battery compartment cover.

NOTE:

When remote control doesn't work in normal or stable condition, or it can't control operation of the

TV set, replace the batteries. (exhausted batteries may leak substance detrimental to the remote

control, replace them immediately when they are weak.)

BASS button

PICTURE Mode button

SOUND System button

TEXT/TV button

GREEN button

Inst. Manual C8ZRL-A (ME) 12/7/05 3:48 PM Page 5

General Operation

Press the Alternate button, and the pro-

gramme position will alternately select

the previous position and the present

position.

Should you wish to mute the sound, (e.g.

While talking on the telephone) press the

Sound Mute button. To switch the sound

back on, press this button again (or press the

Volume + or

button).

-/- -

Direct Programme Selection

Example:

■Press 6button to select programme position 6.

■ To select programme position 27, press the

Digit button, press 0, 2then 7button.

■ To select programme position 215, press the

DIGIT button, press 2,1then 5button.

-/- -

Auto Shut Off Function

This TV set changes to the standby mode within

10 minutes after all broadcasts have ended.

Volume Control

-/- -

Sound Mute

-/- -

Alternate

-/- -

Press the Power ON/OFF button to turn on

or off (Stand-by) the TV set.

Power ON/OFF(Stand by)

You can turn on the TV in the standby mode by

pressing the following button in addition to the

Power ON/OFF button.

●Programme Up/Down button of the remote

control transmitter or the TV set.

●1to 9,0 button on the remote control transmitter.

Lighting of the Stand-by and Power Indicator shows

that there is a power supply. For shutting off a

power supply completely, press Mains POWER

ON/OFF button on the front control of TV set.

To increase or decrease the sound

volume Level.

To select the next or previous programme

position.

Programme Up and Down

-/- -

TV / AV

TV/AV Selector

Press repeatedly to switch to TV, AV1, AV2

or DVD/AV3(VIDEO) mode.

-/- -

BASS

Bass Expander On/Off

Press the BASS button to get an

emphasised bass sound.

Press the Picture Mode button repeat-

edly to select the following picture

modes;

PERSONAL : Your personal preference mode.

DYNAMIC: Suitable for brightly lit room.

NATURAL: Normal viewing mode.

ECO:Suitable for dimly lit room and gives a

cinema-like effect.

GAME:Picture mode that is gantle on the eyes,

suitable for TV game.

Picture Mode Selection

-/- -

PICTURE

Press the Sound Mode button repeat-

edly to select the following sound

modes;

PERSONAL : Your personal preference mode.

MUSIC: Suitable for music programme.

TALK: Suitable for news programme.

NORMAL: Normal listening mode.

Sound Mode Selection

-/- -

SOUND

Inst. Manual C8ZRL-A (ME) 12/7/05 3:48 PM Page 6

General Operation

This TV provides an incredible

3 Dimensional Surround sound effect.

Active 3D Surround

-/- -

SURROUND

Press the SURROUND button to select the fol-

lowing modes.

SURROUND OFF:

To cut off 3D surround effect.

SURROUND 1:

Gives the middle 3D surround effect.

SURROUND 2:

Gives the deep 3D surround effect.

To display the on screen indication, press

the

Recall/Colour System

button.

If the clear sound cannot be obtained,

press the Sound System button repeated-

ly until optimum sound can be produced.

Colour System Selection

-/- -

If the clear picture cannot be obtained,

press the Recall/Colour System button

repeatedly until optimum image can be

produced.

Sound System Selection

Programme Information Call

BG D/K I M

Asound system setting is automatically stored in

the memory.

NICAM

Sound

Status

Off-timer

Programme Position

Sound

System

OFF 5 3

SECAM

NTSC4.43

Acolour system entry to the memory cannot be

made during TV mode, make it during manual tun-

ing mode.

NTSC

PAL

AUTO

AUTO Colour

System

-/- -

S. SYS

A2 Stereo, NICAM Stereo and

Bilingual Broadcast Receiving

■A2

Stereo and NICAM Stereo sound

reception

NICAM

■ Bilingual reception

If the TV receives bilingual programs, the TV ini-

tially selects language A and displays “A” on the

screen briefly. If you want to switch to language B

or MONO (only available in NICAM reception),

press the Stereo/Mono button.

When receiving NICAM stereo broadcast, NICAM

will be displayed on the screen. For A2 (German)

stereo broadcasts, STEREO will be displayed.

When a clear stereo sound can not be obtained

during NICAM or A2 (German) stereo broadcast

due to poor signal reception, press the

Stereo/Mono button to select mono mode.

MONO

STEREO MONO

ABMONO

NICAM Stereo

A2 Stereo

NICAM Bilingual

-/- -

A•B

-/- -

A•B

A2 Bilingual

Note: The Multi Personal Preference Level

Function equip for model CA29FS2 only.

For position 1 through to position 30, the picture

settings (Colour, Brightness and Contrast) and the

volume level that you choose can be stored sepa-

rately in memory for each position. Thus you can

enjoy watching TV channels with optimum picture

and volume settings, even if you change from one

channel to another. 7

Multi Personal Preference Level Function

Inst. Manual C8ZRL-A (ME) 12/7/05 3:48 PM Page 7

-/- -

-/- - -/- -

-/- -

Menu Operation

MAIN MENU

SETTING

PICTURE

PRESET

SOUND

Sound Adjustments

SOUND

EQUALIZER

SOUND PRESET

BALANCE 0

PERSONAL

VOLUME

SURROUND 2

BASS EXPANDER ON

AUTO VOLUME ON

5Press the MENU button repeatedly to exit.

The on-screen menu provides the viewer with

easy

access to adjustments and settings.

■During the menu operation, the following

buttons are used.

To call up the menu.

To go back and to exit the menu.

To move around the

menus.

To move around the menus.

To make adjustments.

2Press or to display “SOUND” menu.

1Press the MENU button to display main menu,

and “SOUND” will be selected first.

3Select an item with or .

•

BALANCE :

Left and Right speaker volume balance

adjustment.

•SOUND PRESET (Sound Mode Selection):

Enable to select the suitable sound adjustment

(PERSONAL, MUSIC, TALK, NORMAL). Also

possible to select directly with the Sound

Mode button.

Note: Your sound adjustment will be memorized

to “PERSONAL” of the Sound preset

automatically.

•

SURROUND :

Enable to select active 3D surround modes

(SURROUND OFF, 1or 2). Also possible to

select directly by pressing the SURROUND

button of the remote control.

•

AUTO VOLUME (ON/OFF) :

This function automatically equates the sound

volume of each position. It is used to prevent the

sharp volume change when you change the

channel.

4Press or to adjust.

■ Equalizer Adjustment

There are 5 types EQUALIZER adjustment:

•

100 Hz Adjustment