Sansui ES-24F1 Manuel utilisateur
Wide TFT-LED Monitor
User's manual
In order to avoid accident and risk,Please
read the “Important safety notice”and
instructions before using the monitor.
Model No.:ES-24F1
Monitor
LED
CONTENTS
-1-
Contents
-2-
Contents
3. Operation
3.1 Button Function description
3.2
3.3 Plug and Play
3.4 Power Management System
4. Technical Specification
4.1 Product Specification
11
13
25
25
26
27
4.2 The table of VGA default mode
Troubleshooting23
Main Menu
1.2 General Features
1.3 Technical Features (Overview)
1.4 Precautions
1.5 Package Contents
1
3
6
6
7
8
9
2.1 Hardware Setup
2.2 Connecting the Screen 10
1. Introduction
CONTENTS
2. Installation
1.1 Important Safety Instructions
-3- -4-
Introduction
Introduction
1.1 Important Safety Instruction
The lighting flash with arrowhead symbol, within a triangle, alerts
the user to “dangerous voltage” which could cause electric shock.
The exclamation point within a triangle indicates to the user to read
important operating and maintenance instructions in the manual.
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and third grounding prong. The wide blade or third prong
are provided for your safety. When the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched, particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used caution when
moving the cart/apparatus combination to avoid injury tip-over.
13. Unplug this apparatus during lightning storms or when unused for long
periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture,
-5- -6-
Introduction
Introduction
TM TM
TM
R
1.3 Technical Features- Overview(for complete specification
please refer to section 5)
DDC1 and DDC2B for Plug & Play compatibility
VESA DPMS power saving standard
1.2 General Features
Please read this information carefully to ensure viewing pleasure,
functionality and safety when using the monitor.
sources, including direct sunlight. To prevent the spread of fire, keep candles or other
21. Never place the TV, remote control or batteries near naked flames or other heat
flames away from the TV, remote control and batteries at all times.
22. The USB terminal should be loaded with 0.5 A under normal operation.
does not operate normally, or has been dropped.
Warning : To reduce the risk of fire or electric shock, do not expose this
apparatus to rain or moisture.
15. The apparatus shall be disconnected from the mains by placing the
power/standby switch in the standby position and unplugging the power cord
of the apparatus from the AC mains receptacle.
16. The receptacle shall be installed near the equipment and shall be easily
accessible.
17. This product should never be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
18. Apparatus shall not be exposed to dripping or splashing.
19. Do not place any sources of danger on the apparatus (e.g. liquid filled
objects, lighted candles).
20. Wall or Ceiling Mounting - The appliance should be mounted to a wall or
ceiling only as recommended by the manufacturer of the wall mount bracket.
-7- -8-
Introduction Introduction
Your LED Monitor package includes the following parts:
1.5 Package contents
If you find any of the above items damaged or missing , please
contact your local dealer.
Wide Screen LED Color Monitor with foot
HDMI Cable and Type C able
User Manual
1.4 Precautions
Sit at least 18in away from the screen.
Do not apply pressure to the screen! The LED element is very delicate.
Do not touch the screen directly with your fingers. Substances from
your skin may damage the screen and be difficult to remove.
Always make sure the LED environment is clean and dry..
Power Macintosh, Power PC and compatible
International Standards: FCC
External power supply
VGA modes for IBM or PC compatible
Resolution SVGA 1366x768 Pixel (18.5”) 1920x1080 Pixel (21.5-24”)
Adapter
-9-
Installation
-10-
2.2 Connecting the Screen
A) Make sure, both of your PC and the screen are turned off.
B) Connect the signal cable: Plug in one end of the signal cable to
the appropriate 15 pin D- SUB connector at the back of the
monitor. Plug in the other end of the signal cable into the VGA
output of your computer. Tighten the two connection bolts on
each plug.
C) Connect the power cord:
Plug in the male end of the power
cord to the power socket.
Installation
2.1 Hardware Setup
2. Installation
Set your monitor on a stable and even surface.
Make sure the receptacle and the PC are near the
monitor to avoid any tension on the signal cable or the power cord.
Choose a well-ventilated space to position your monitor. Avoid
exposing the LED to direct sunlight.
Adjust the environmental light for the best viewing condition.
to your personal preference.
Adjust the tilt of the screen (between~-0 to ~180 as shown below)
-11-
Operation
-12-
3. Operation
3.1 Button Function description
Operation
1、Press menu key display OSD and enter.
2、Press menu key display source(VGA/HDMI/TYPE C optional).
3、Press up key volume+，Press down key volume-.
4、Press down key brightness-，Press up key brightness+.
DC IN
EARPH ONE
VGA
HDMI TYPE-C
Button Function
DC IN
EARPHONE
VGA
HDMI T YPE-C
-13- -14-
Operation
Operation
3.2 Main Menu
Press MENU button, and the main menu page will appear as follows:
BRIGHTNESS
Brightness
Press ▼/▲ button to select Brightness, then press MENU button to confirm
your selection and press ▼/▲ button to adjust.This item can adjust the optical fiber
output of the entire picture, and it will affect the dark region of the picture.(0-100)
Contrast
Press ▼/▲ button to select Contrast, and then press MENU button to confirm
your selection
and press ▼/▲ button to adjust.This item can adjust the highlight intensity of the
picture, (0-100)
but the shadow of the picture is invariable.
ECO
Press ▼/▲ button to select ECO, and then press MENU button to confirm your selection
and press ▼/▲ STANDARD,RTS,FPS,TEXT,MOVIE,GAME Mode .
DCR
Press ▼/▲ button to select DCR , press MENU button to confirm your selection
and press ▼/▲ ON/OFF.
IMAGE
Press ▼/ ▲ button to select IMAGE, and then press MENU button to confirm your selection.
This item can adjust the configuration automatically.（VGAMode）
Press the Menu button to get into the BRIGHTNESS MENU, and then press MENU button to enter.
-15- -16-
Operation Operation
H.Position
Press▼/▲button to select H.Position, and then press MENU button to confirm your selection.
Press ▼ button image will move toward the left side. Press ▲ button image will move toward the right side.
V.Position
Press ▼/▲ button to select V.Position, and then press MENU button to confirm your selection.
Press ▼ button image will move down. Press ▲ button image will move up.
Clock
Press ▼/▲ button to select Clock, and then press MENU button to confirm your selection and press ▼/▲
button to adjust.
Phase
Press ▼/▲ button to select Phase, and then press MENU button to confirm your selection and press ▼/▲
button to adjust.
ASPECT :
Press ▼/▲ button to select Phase, and then press MENU button to confirm your selection and
Press ▼/▲ button to adjust. (AUTO WIDE or 4:3).
Press ▼/▲ button to select Color in the main menu, and then press MENU button to enter.
Color TEMP.
Press ▼ /▲ button to select COLOR TEMP, and then press MENU button to
confirm your selection and press ▼/▲ button to adjust.
This item can change the value of RGB to adjust the image tune.
COLOE TEMP：WARM/USRE/COOL）
Press ▼/▲ button to select User,
and then press MENU button to customize temperature.
-17- -18-
Operation Operation
Red®
Press ▼/▲ button to select Red, and then press MENU button to confirm your selection and press ▼/▲ button to
adjust the value of the three primary colors of red.
Press ▲ button to increase the number, and the picture color will become redder as the increasing number.
Press ▼ button to decrease the number, and the picture color will become greener as the decreasing number.
Green(G)
Press ▼/▲ button to select Green, and then press MENU button to confirm your selection and press ▼/▲ button to
adjust the value of the three primary colors of green.
Press ▲ button to increase the number, and the picture color will become greener as the increasing number.
Press ▼ button to decrease the number, and the picture color will become redder as the decreasing number.
Blue(B)
Press ▼/▲ button to select Blue, and then press MENU button to confirm your selection and press ▼/▲ button to
adjust the value of the three primary colors of blue.
Press ▲ button to increase the number, and the picture color will become bluer as the increasing number.
Press ▼ button to decrease the number, and the picture color will become more yellow as the decreasing number.
LOW BLUE LIGHT
Press ▼/▲ button t o s elect low blue light, and then press MENU button to confirm your selection and
press ▼/ ▲ button to adjust low blue light.
FULL
LANGUAGE
Press MENU button to LANGUAGE , Press ▼/▲elect LANGUAGE(Options:English/
French/ /Chinese/Italian/Spanish/Portuguese/Turkish/polish/Nederlands/Russian/Deutsch
Korean...)
OSD H.POS
Press▼/▲button to select OSD H.Pos, and then press MENU button to confirm your
selection and press ▼ button OSD menu will move toward the left side. Press ▲ button
OSD menu will move toward the right side.
OSD SETTING
Table des matières
Autres manuels Sansui Moniteur
