SANLI Red Back Manuel utilisateur

LAWN MOWER

CONSUMER

HELPLINE

1800 466 068

PLEASE READ THE INSTRUCTIONS IN THIS MANUAL BEFORE OPERATION.

Red Back

RCS405

INSTRUCTION MANUAL

PAGE 2

INSTRUCTION MANUAL

RCS40 LAWN MOWER

×1

×2

×4

1. Petrol Engine Mower

4. Grass Catcher

7. Spark Plug Socket 21mm

2. Instruction Manual

5. Spanners

8. Cable Clips

3. Handle Knobs and Bolts

6. Bolt and Nut Assembly

What you get with your mower

×1

9. Spring Cord Guide

PAGE 3

1. Comfort Grip Handle

2. Throttle Control Lever

3. Rear Flap

WWW.SANLI.COM.AU

4. Fuel Tank

5. Air Filter

6. Spark Plug

8. Oil Sump

9. Height Adjustment Lever

10. Grass Catcher

11. Spring Cord Guide

PAGE 4

Remove and ensure you have all the parts

required for assembly (see page 2 for reference)

Parts required:

4 x Bolts and Nuts

1. LOWER HANDLE BAR ASSEMBLY

1. Lower Handle Bar Assembly

Attach lower handle bar bolts. Take the

weight of the handle bar and fit the lower

2a. Locate the Starter Cord

Pull the starter cord up to the spring

and hold the cord at the lower side

ofthe spring. Rotate the string clockwise

around the spring.

INSTRUCTION MANUAL

PAGE 5

2. UPPER HANDLE ASSEMBLY

4. 5. 6.

2. Upper Handle Assembly

Fit the right side Handle Knobs and

Bolts.

3. Fit the Cable Clips

Push the cable clips into place.

ASSEMBLY GUIDELINES

LAWN MOWER RCS405

4. Attach the Grass Catcher

Lift the Rear Flap with one hand.

5. Attach the Grass Catcher

Lower the Grass Catcher

hook onto bar.

6. Complete machine readyfor your

lawn.

Parts required:

2 x Handle Knobs

2 x Bolts

1 x Spring Cord Guide

PAGE 6

INSTRUCTION MANUAL

BEFORE YOU BEGIN

WARNING! The following procedures must be carried out before you start the engine of your lawnmower.

FILL OIL SUMP WITH 600ml of

SAE 30 Oil

FILL FUEL TANK WITH

PREMIUM PETROL (NO

E10 PETROL)

MAX MIN

Filling oil sump with oil

The mower is supplied with oil in

the engine. You have to add 600ml

oil before starting the engine for

the rst time.

1. Firstly, remove the warning

label from under the dipstick,

then remove the dipstick and

slowly pour 600ml of SAE30

or 10W/30 lawnmower grade

engine oil into the engine via

the oil ller (Fig. 1). Replace the

dipstick and tighten.

2. Before you use the mower each

time, check the oil level (Fig.

2) and if necessary top up with

SAE30 engine oil. To check the

oil level, unscrew the yellow

dipstick, wipe with a rag and

replace into the oil ller (do not

screw back in place),

remove the dipstick again and

check the level.

3. The oil level must be between

the min and max marks on the

dipstick (Fig. 3). Replace the

dipstick and screw into place.

Fill Fuel tank with min 95 octane

premium unleaded petrol (Do not

use Ethanol petrol ie. E10).

Petrol is highly ammable so

extreme caution must be taken

when handling it. Always store

petrol in approved containers and

you must ensure that you use fresh

petrol that is less than 4-6 weeks

old. Do not mix oil with petrol.

4. To put petrol in the fuel tank,

rstly remove the warning label

from under the petrol cap.

It’s best to ll the tank using

a clean funnel, but never ll it

completely (Fig. 4) . Instead,

leave at least 13mm from

the bottom of the ller neck to

allow for expansion. Ensure that

you securely tighten the petrol

cap after lling. (Funnel & Fuel

not supplied).

Fig 1 Fig 2 Fig 4

Fig 3

PAGE 7

WARNING! The following procedures must be carried out before you start the engine of your lawnmower.

ON OFF

RUN

COLD

START

STOP

RUN

COLD

START

STOP

BEFORE YOU BEGIN/STARTING THE ENGINE

LAWN MOWER RCS405

STARTING THE ENGINE

Starting the engine

1. Make sure that your mower is

on a safe, at area (a paved area

or path is ideal - avoid thick wet

grass and gravel surfaces) away

from fuel or fueling area to

make starting safe.

2. Slide the ‘Red’ petrol tap lever

to the left ‘On’ position (Fig. 5).

3. Move the throttle control lever

located on the handle to the

‘Cold Start’ position

(Fig. 6).

4. Firmly hold the top handle with

one hand, and then with your

other hand pull the cord slowly

until you feel resistance. Then

pull vigorously with one steady

action (Fig. 7). Guide the cord

back to it’s rest position (do not

release).

5. When the engine has been

running for at least 15 seconds

(more time on cold days) (Fig. 8)

adjust the throttle control lever

to the ‘Run’ position.

6. To restart a hot engine, move the

throttle control lever to the ‘Run’

position and then refer to ‘

Point 4’ .

7. To turn off your mower, slide the

throttle control lever down to the

‘Stop’ position. After it has stopped,

slide the ‘Red’ petrol tap lever to

the right ‘Off’ position.

RUN

Fig 5 Fig 6

Fig 7 Fig 8

PAGE 8

INSTRUCTION MANUAL

USING YOUR MOWER

ON OFF

Attach the Grass Catcher

The grass catcher attaches easily by

lifting the mower’s Rear Flap with

one hand (Fig. 9) and slide the Grass

Catcher into position (Fig. 10).

Cutting Height Adjustment

For best results adjust the cutting

height of your mower to suit the

mowing conditions. Do not try to

remove too much grass in one pass.

Adjustment of the cutting height is

made centrally. Take hold of the cut

height adjustment lever, positioned on

the mower’s righthand rear wheel.

Move the lever outwards to release

it from its locating notch. Move

the lever towards the front of the

machine to increase the cutting height

and towards the rear to reduce the

cutting height. Return the lever to

the locating notch to set the desired

cutting height.

securely into its serrated holder.

Mowing your Lawn

Start your mower (see: Starting the

engine). After mowing and emptying

the Grass Catcher ensure the engine

is not running and turned off.

Cleaning your Mower

Cut grass is damp. Regular cleaning

after each use will ensure better

functioning of the mower and reduce

the risk of corrosion or seizure.

the engine to cool then remove

accumulated grass clippings from and

around the engine with a brush. Clean

the grass collection bag annually with

a brush or gentle spray of water and

allow to dry.

Clean underneath regularly -

disconnect the spark plug cap and tilt

the mower on back. Remove cut grass

from the cutting system with a scraper

and a brush.

Do not use a pressure washer or hot

water to clean the mower. Dry off the

machine before storing by leaving it

clear surface to prevent corrosion or

seizure.

Storing your Mower

Store your mower in a dry, well-

sparks or heat sources. Disconnect the

spark plug cap. Avoid storing beneath a

tarpaulin or similar cover as it may

cause condensation resulting in

corrosion.

Transporting your Mower

Ensure the fuel tank is empty. Run

the engine until any remaining fuel is

consumed. Allow the engine to cool.

Turn fuel tap to OFF position (Fig. 13).

How to cut for best results

For best results cut your lawn in

alternative directions switching

direction each time you cut. Cut your

lawn at an equal and same height.

Slightly overlap your cutting lines.

WARNING!

Turn mower off before

adjusting cutting height lever

Turn mower off before cleaning

Fig 9 Fig10

Fig12 Fig13

Fig11

PAGE 9

Max 20°

HOT!

RUN

COLD

START

STOP

1. Beforestarting your mower inspect

it carefully to ensure that there are

no loose parts and that it is in good

working order.

2. Be sure of your footing.

Always walk, never run, when

operating the lawnmower.

3. Keep hands, feet and clothing away

from the mower’s moving parts

always wear appropriate footwear

(avoid sandals or open shoes).

4. Never put your hands or feet

underneath the chassis of the

lawnmower while the engine is

running.

5. Clear the area to be mowed of any

stones, sticks, wire and debris

before beginning. Always ensure

that you mow a safe distance away

(over 14 metres) from adults,

children and animals.

6. Turn off the engine and disconnect

the spark plug cap before

cleaning, transporting, or making

adjustments. Never leave the

mower unattended.

7. Never open the fuel ller cap, or

ll the tank, if the engine is still

hot after use. Please ensure that

you securely tighten the petrol cap

after lling.

14. Do not transport the

mower in a vehicle if there

is any petrol in the tank.

15. Be aware that the machine’s

exhaust area and other parts

of the lawnmower get very

hot during and right after use.

16. Turn off the engine before

emptying the grass-catcher and

before clearing any grass caught in

the rear ap where the catcher ts.

17. Store fuel and oil in a cool well-

ventilated place, away from direct

sunlight and gas cylinders or hot

water heater systems.

18. It is recommended that you wear

a ear protectors, safety goggles

and safety boots when using

alawnmower.

19.To inspect the underside of your

mower, only tilt the lawnmower to

your right, or back, when standing

behind it (this is the side where

the exhaust is near the ground)

otherwise oil may leak into

inappropriate areas of the engine.

Never tilt the lawnmower when

the engine is running.

20. All servicing and repair work

under warranty must be carried

out by an Authorised Dealer.

USING YOUR MOWER/SAFETY TIPS

LAWN MOWER RCS405

TIPS ON MOWER SAFETY

8. Mow across the face of slopes, not

up & down, and avoid mowing on

very steep slopes. We recommend

you avoid mowing when it is

raining, after nightfall or in poor

light conditions.

9. Do not operate the machine by

pulling it towards you as you risk

pulling it onto your feet. Instead,

always push and walk behind your

lawnmower.

10. Do not ll the tank, or start the

lawnmower indoors, or in a poorly

ventilated area, as exhaust gases

contain poisonous substances

and petrol fumes are ammable

and dangerous.

11. Do not alter engine governing

settings or over-rev the engine, as

excessive speed is dangerous and

can reduce engine life.

12. Do not smoke when lling

the fuel tank, using the machine,

or when petrol is in the immediate

area. Never use or store the

mower near a naked ame.

13. Always use fresh 95 octane

premium unleaded petrol that is

not more than 4-6 weeks old. Fill

the tank using a funnel, but never

completely. Clean up any over ow

or splashes before starting.

3/4 5 7

19128

PAGE 10

INSTRUCTION MANUAL

MAINTENANCE SCHEDULE

WARNING! The following procedures must be carried out before you start the engine of your lawnmower.

SUMMARY OF REGULAR MAINTENANCE

REQUIRED BY THE MOWER

Before each

mowing After 5 hours Every 25 hours or once a year

minimum before winter lay-up

Cutting system Check and verify

its condition

Sharpen and balance blade.

Replace worn or damaged blade.

Spark plug Check

Clean and check the clearance

of the electrodes. Replace if

necessary.

Air Filter Check necessary.

Oil Check the level Drain and

renew Drain and renew

OUT

Frequency

Components

Cutting System

Before and after each mowing

session, check that the blade, its

attachment bolts and drive shaft

are not damaged or excessively

worn. Never try to straighten a

bent blade. Replace a damaged,

worn or bent blade as soon as

possible. Use only genuine SANLI

parts or those approved by SANLI.

Excessive vibration when mowing

is a good indication of a problem

with the cutting system.

Removing the blade

Wear appropriate protective

gloves to prevent possible

injury when handling the blade.

Disconnect the spark plug cap

and tilt the mower on its side with

uppermost.

hand, use a spanner or socket to

loosen the blade screw.

Sharpening the blade

For best mowing results, have the

edges sharpened and the blade

balanced at least once a year by a

specialist service dealer or agent.

Mounting the blade

Wear appropriate protective gloves

to prevent possible injury when

handling the blade. Disconnect

the spark plug cap and tilt the

uppermost.

Check that all components (the

blade, key, blade holder, screws and

washers) are present, clean and in

good condition.

Position the blade on its support

engine.

Check the correct alignment and

matching of pads with the blade.

The blade must be positioned

precisely on its stand.

Tighten the screws connecting all of

check that all parts are present and

(NB wear suitable gloves).

Spark Plug

Check the spark plug initially after

Thereafter, maintenance of the spark

plug should take place every 25 hours.

Remove the spark plug cap (Fig.14)

using a rotary motion and then remove

the spark plug with the wrench

provided (Fig.15).

Clean off any carbon deposits using a

copper brush and check the electrode

gap with a feeler gauge (the gap should

be ≈ 0.7 mm). Replace and tighten the

serviced spark plug and replace the

cap.

If the spark plug is worn or damaged,

replace with a new spark plug of the

same or suitable type for the engine.

We recommend to use NGK

BPR6ES or Torch F6RTC for Sanli

mowers.

If in doubt, contact your point of

purchase or local dealer.

WARNING!

Vibration from a bent or damaged

blade can cause costly damage to the

mower. Working with an excessively

worn blade wastes fuel and can

lead to injury if the blade becomes

detached from the machine.

Fig14

Fig15

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels SANLI Tondeuse à gazon

SANLI

SANLI Bumble Bee Jnr BBJ300 Manuel utilisateur

SANLI

SANLI LS 40 Manuel utilisateur

SANLI

SANLI TBH 1066A Manuel utilisateur

SANLI

SANLI SSP550 Manuel utilisateur

SANLI

SANLI LS 40 Manuel utilisateur

SANLI

SANLI LS 430 P7R Manuel utilisateur

SANLI

SANLI Victory BIG350 Manuel utilisateur

SANLI

SANLI PCS355 Manuel utilisateur

SANLI

SANLI SSP550 Manuel utilisateur

SANLI

SANLI LazerCut LCS400 Manuel utilisateur

SANLI

SANLI TBH 1066A Manuel utilisateur

SANLI

SANLI LBP350 Manuel utilisateur

SANLI

SANLI LS42 Manuel utilisateur

SANLI

SANLI LazerMulch LMS400 Manuel utilisateur

SANLI

SANLI ADR1130 Manuel utilisateur

SANLI

SANLI LazerMulch LMS405 Manuel utilisateur

SANLI

SANLI Power Mulch PMS405 Manuel utilisateur

SANLI

SANLI Bull Ant PCS350 Manuel utilisateur

SANLI

SANLI LazerCut LCS405 Manuel utilisateur

SANLI

SANLI Bumble Bee BBP400 Manuel utilisateur

SANLI

SANLI LBP 480 ABS Manuel utilisateur

SANLI

SANLI LBP 510 S9A Manuel utilisateur

Manuels Tondeuse à gazon populaires d'autres marques

RHINO

RHINO 1958 Manuel utilisateur

Wolf Garten

Wolf Garten Compact plus 40 B Manuel utilisateur

Cub Cadet

Cub Cadet LTX 1045 Manuel utilisateur

Craftsman

Craftsman 917.378461 Manuel utilisateur

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manuel utilisateur

Challenge

Challenge CH18V2 Instructions de fonctionnement

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manuel utilisateur

DEWEZE

DEWEZE ATM-725 Manuel d'utilisation

Weed Eater

Weed Eater 180083 Manuel utilisateur

Husqvarna

Husqvarna Poulan Pro PP185A42 Manuel utilisateur

Better Outdoor Products

Better Outdoor Products Quick Series Manuel utilisateur

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manuel d'utilisation

MTD

MTD 795, 792, 791, 790 Manuel utilisateur

Toro

Toro Groundsmaster 3505-D Manuel utilisateur

Dennis

Dennis FT 610 Manuel utilisateur

AIRFORCE

AIRFORCE F-15 Gen 3 Manuel utilisateur

MTD

MTD 126-220-000 Manuel utilisateur

Toro

Toro 74806 Manuel utilisateur