Samsung WF365 Series Manuel

WASHING MACHINE

Technical Information

ModelS : WF361*

WF363*

WF365*

WF364*

Code No. : DC68-03207A-03_EN

• Duetopossibilityofpersonalinjuryorpropertydamage,alwayscontactanauthorized

technicianforservicingorrepairofthisunit.

• RefertoServiceManualfordetailedinstallation,operating,testing,troubleshooting,and

disassemblyinstructions.

AllsafetyinformationmustbefollowedasprovidedinServiceManual.

CAUTION

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

[BIGBANG]Technical_information-03207A-03_EN.indd 1 2013-7-16 17:15:01

ALIGNMENT AND ADJUSTMENTS

GENERAL ERROR FUNCTION

Error Code

(Diagnostic Code

Error Image)

Description Corrective Action

1nd

Thewaterlevelfailstodropbelow

theResetWaterLevelwithin15

minutes.

Goto“WillNotDrain”

TroubleshootingSection.

2LO DoorfailstoUnlockAfter7attempts. Goto“WillNotUnlock”

TroubleshootingSection.

3nF

WhenthellingContinuesfor

morethan40minutesorthereisno

changeofwaterlevelfor6minutes.

Goto“NoWaterFill”

TroubleshootingSection.

4 FL Doorfailstolockafter7attempts. Goto“WillNotLock”

TroubleshootingSection.

5 LE

AwaterlevellowerthantheReset

waterlevelisdetectedfor5seconds

duringtheWash/Rinsecycle.

Goto“NoWaterFill”Troubleshooting

Section.

6 1E

WaterLevelSensorTrouble.(When

theinputsignalfromthewaterlevel

sensorisoutofrange,theunitwill

sendoutbeepingsoundsandhalts

thecycle.)

Goto“NoWaterFill”

TroubleshootingSection

7OE

Afaultisdetectedinthewaterlevel

sensor.Data(frequency)shows

thewaterlevelisatorabovethe

overowwaterlevel.(Whenthis

conditionisdetected,themachine

willautomaticallystartsdraining

wateruntilthewaterlevelfalls

belowtheresetwaterlevel)

Firstchecktoseethatallofwater

valvesarenotstuck.Ifwatervalves

areOK,checkwaterlevel.

8dc

Unbalanceorcabinetbumpis

detectedduringnalspin,which

preventsthedrumfromspinning

over150rpm.(Neverexceeds150

RPMduetounbalancedload)

Goto“WetClothes”Troubleshooting

Section.

9 E2

JammedKey.(Whenkeyinput

signalsarecomingoutformorethan

30seconds,itisregardedasajam.)

Checkallofkeys.IfAkeyissensed

tobepressed,allkeyswilldonot

respond.

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

[BIGBANG]Technical_information-03207A-03_EN.indd 2 2013-7-16 17:15:01

ALIGNMENT AND ADJUSTMENTS

Error Code

(Diagnostic Code

Error Image)

Description Corrective Action

10 ds Doorisdetectedasopenwhileitis

tryingtolockthedoor.

Goto“QuickTestMode”andthendo

DoorLock/UnlockTest

11 tE

Abnormalhigh/lowtemperatureor

resistance(ThermalsensororPBA

resistance).

Goto“BoardInputTest”andcheck

WaterTemperature.Checkloose

orpinchedwires.ReplacePCBor

thermistor.

12 3E

MICOMisattemptingtodrivethemotor

butisnotgettinganyresponsesignals

fromthehallsensor.Visualcheckshows

motorisnotrunning.(Locked,Defective

HallSensororOverload)(WF364*)

Evaluatewireharnessforlooseor

unhookedconnections.Goto“

QuickTestMode”andtestMotor.

MICOMisattemptingtodrivethe

motorbutisnotgettinganyresponse

signalsfromthecurrent.Visualcheck

showsmotorisnotrunning.(Lockedor

Overload)

13 Hr HeaterRelayFailure(NoHeater

RelayCheckSignal) ReplacePCB

14 nF1 Thehot/coldwaterhoseconnection

isnotcorrect.

Pleaseconnectthehot/coldwater

hoseconnectioncorrectly.

15 2E Voltageformotorcontrolbusisover

orunderspeciedlimit. ReplacePCB

16 SUd

Sudsisdetectedduringthewashing

session.(“SUdS”isnotanerror.Ifthe

washerisinsudsperiod,“SUdS”will

lightupinsteadofremainingtime.)

Guideausertoreduceamountof

detergentusage.

17 AE

CommunicationerrorbetweenSUB

PBAandMAINPBA

CheckMainPBA,SUBPBA&Wire-

harness.ReplacePCB

18 SF SystemError ReplacePCB

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

[BIGBANG]Technical_information-03207A-03_EN.indd 3 2013-7-16 17:15:02

ALIGNMENT AND ADJUSTMENTS

TEST MODE

Test Mode:

EachTestModefortheBIGBANGisasfollowsin

thecomingpages.Thetestmodesindicatedby

theredarrowsaremodesunabletogetanaccess

oncethewashingcyclehasstartedduetosafety

resons.

Quick Test Mode

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

Special Test Mode

Power Off State

Quick Test Mode

EEPROM Clear

Mode

Continuous Cycle

Mode

Service Mode

Demo Mode

Quick Spin Test Mode

Cycle Count Check Mode

S/W Version Check Mode

Fast Time Down Test Mode

Board Input Test Mode

Diagnostic Code

CheckMode

Power On State

(Normal User Mode)

211

2 7

6 8

[BIGBANG]Technical_information-03207A-03_EN.indd 4 2013-7-16 17:15:03

ALIGNMENT AND ADJUSTMENTS

Denition of Quick Test Mode:

- CheckoperationofallLED’s(VerifyfaultyLED).

- Checkmodelandsoftwareversion.

- Checkdierentoperatingmodes(e.g.watervalve,motor,door,drainpump,etc.).

How to Enter:

- Plugintheunit.

- PressSoilKey,SpinKeyandPowerKeyatthesameTime.

Quick Test Mode:

1. AllLED’slightupanditsendsoutBeepSoundwhenit

entersintotheQuickTestMode.(Including7-Segment)

2. DisplayssoftwareversionforasecandClearEEprom.(Ex.If

S/WVersionis04,7-SegmentwilldisplayUd04)

3. Whentheversionisdisplayed,turntheJog-Dialsothat

theversiondisappears.Pressthefollowingkeystotestthe

variouscomponents.

-TempKey:WaterValveTest

-SpinKey:DoorLock/UnlockTest

-SoilKey:WaterHeaterTest

-Signal:DrainPumpTest

EEPROM Clear Check

Denition of EEPROM Clear Mode:

- EEPROMinitialization.

- Allcourse/optionsettingsaretoberesettodefault

valuesafterEEPROMinitialization.

- WhenServicearisesanditneedsPCBreplacement,

EEPROMshouldbereset.

How to Enter:

- Theunitneedstobeon.

- PressDelayStartKey,andPowerKeyatthesame

time.

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

[BIGBANG]Technical_information-03207A-03_EN.indd 5 2013-7-16 17:15:04

ALIGNMENT AND ADJUSTMENTS

Continuous Run Mode

Denition of Continuous Run Mode:

- WillcontinuouslyrepeatthecurrentcycleuntiltheContinuousRunModeiscancelled.

How to Enter:

- PressDelayStartKey+ChildLockKey(Spin+SoilLevel)togetherfor7sec.

Continuous Run Mode:

1. Press

DelayStartKey+ChildLockKey(Spin+SoilLevel)

for7secduringPowerOnState(Normal

UserMode).

OnceinContinuousRunMode,Thesevensegmentswillnolongerdisplay“0000”andwillalternate

betweendisplayingthenumberofcyclesofthecompletedcourseandtheremainingtimeofthecourse.

3. TheContinuousRunModewillrepeatthepreviouscycleuntilcontinuousrunmodeiscancelled.

DuringContinuousRunMode,pressDelayStartKey+ChildLockKey(Spin+SoilLevel)for7secto

returntonormalusermode.Thesevensegmentswillnolongerdisplaythenumberofcyclesand

willdisplaythemaintenancetimeonly.

5. IfyouexitServiceModeafterenteringitfromContinuousMode,thewashingmachinereturns

toContinuousMode.

6. IfpowerislostinContinuousRunMode(thatis,whenthepowerplugisdisconnectedorthe

Powerkeyispressedturningthewashingmachineo),themodeisreleasedwhenthewashing

machineisturnedonagain.

Service Mode

Denition of Service Mode:

- ServiceModeenablesservicetechnicianstoverifytheoperationofthewashingmachineand

dotroubleshooting.

- ServiceModecanbeenteredduringallwashingcyclewithoutinterruptingthecycleexcept

someoftestmodes.

- VarioustestscanbedonewithServiceMode.So,troubleshootingcanbedonebasedonthe

resultingdiagnosticcodes.

How to Enter:

- ToentertheServiceMode,presstheDelayStart+SpinKeyfor3secondsoruntiltheunitsends

outbeepingsounds.

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

[BIGBANG]Technical_information-03207A-03_EN.indd 6 2013-7-16 17:15:04

ALIGNMENT AND ADJUSTMENTS

Service Mode

Service Mode:

1.ThewashermustbeontogointotheServiceMode.

2.Themotorspeedwillbedisplayedwhenstarted(Itdisplays0whenthemotordoesnotspin).

3.Thepresentstateofthemachinewillnotbechanged.

(i.e.,thecurrentcycleinprogresswillnotbeinterruptedandonlythedisplaywillchange)

4. ToexitServiceMode,pressDelayStart+SpinKeyfor3secondagain,orPowerKey.Ifnokeyis

operatedduringServiceModefor5minutes,themachinewillreturntonormalusermode.

Quick Spin Test Mode

Denition of Quick Spin Test Mode:

- QuickSpinTestModeistodoSpinCheck.(HighRPM)

How to Enter:

- DuringServiceMode,presstheDelayStartandTemp.Keysfor3secondstoenterQuickSpin

TestMode.

- Cannotenteroncethewashingcyclehasstarted.

Quick Spin Test Mode:

AsitentersintotheQuickSpinTestMode,itstartsspinningandreachestoitsmaximumRPM.

OncetheSpinspeedreachesthemaximumRPM,thespeeddropsimmediately.

ToholdQuickSpinTestMode(enteringHoldSpeedMode),presstheStart/Pausebutton.Ifthe

Start/PausebuttonispressedduringQuickSpinTestMode,itwillstopacceleratingandholdits

spinningspeedfor10minutesbeforegoingbacktoQuickSpinTestMode.

Also,tocanceltheholdandallowQuickSpinTestModetocontinue,presstheDelayStartand

TempKeystogetherfor3seconds.

IfyouholddowntheDelayStartandTemp.keysforthree(3)secondswhenthewashingmachine

isnotinHoldSpeedMode,QuickSpinModeisexitedandServiceModeisrestored.

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

[BIGBANG]Technical_information-03207A-03_EN.indd 7 2013-7-16 17:15:05

ALIGNMENT AND ADJUSTMENTS

Cycle Count Check Mode

Denition of Cycle Count Check Mode:

- CycleCountCheckModeistotallyupthenumberofwashings.

How to Enter:

- ToentertheCycleCountCheckMode,presstheSignalKeyduringServiceMode.

Cycle Count Check Mode:

1. ActivatetheServiceModeinadvance.

2.WhentheSignalkeyispressed,thetotalnumberofwashingswilllightupandasignalLEDwill

glow.

3.Themaximumnumberofcycleswillbe1999.

Thecounterwillrolloverto0andstartcountingagainafter1999.

4.Thecountingwillbecarriedoutattheendofthenormalcycle.

(FornormalandContinuousRuncycles,thecountiscarriedoutattheendofthecycles.

5. ToexittheCycleCountCheckMode,pressthe“Signal”keyagain.

S/W Version Check Mode

Denition of S/W Version Check Mode:

- S/WVersionCheckModeistobringupS/WVersioninformation.

How to Enter:

- ToentertheS/WVersionCheckMode,presstheSoilLevelKeyduringServiceMode.

S/W Version Check Mode:

1. ActivatetheServiceModeinadvance.

2. PresstheSoilLevelKeytobringupitssoftwareVersion

EX)GenerateUd04atVersion04(UdisMicomcode,04isit’ssoftwareversion)

3. ToexittheS/WVersionCheckMode,presstheSoilLevelS/Wonceagain.

Then,itreturnstotheServiceModewithmotorRPMilluminating.

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

[BIGBANG]Technical_information-03207A-03_EN.indd 8 2013-7-16 17:15:06

ALIGNMENT AND ADJUSTMENTS

Fast Time Down Test Mode

Denition of Fast Time Down Test Mode:

- FastTimeDownTestModeistoforwardtheprogramtothenextcyclestage.

How to Enter:

- ToentertheFastTimeDownTestMode,presstheTempkeyduringServiceMode.

Fast Time Down Test Mode:

1. ActivatetheServiceModeinadvance.

2. Toforwardtheprogramtothenextcyclestage,presstheTempkey.

Each stage is located at key points of a complete cycle as follows:

- EndofEachFill(BeginningofWashorRinseTumbleSession)

Caution:CheckifthecurrentwaterlevelishigherthantheResetwaterlevelandthenperform

theFasttimedowntest.

- BeginningofDrainSession

- BeginningofSpinSession(Here,itchecksthewaterlevel.So,ifitisovertheresetlevel,itcarries

outdrainingbeforethespinning.)

- BeginningofFillSession

- BeginningofBleachFill

- BeginningofFabricSoftenerFill

- Every3minutesduringWashandRinseTumbleSession

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

[BIGBANG]Technical_information-03207A-03_EN.indd 9 2013-7-16 17:15:06

ALIGNMENT AND ADJUSTMENTS

Board Input Test Mode

Denition of Board Input Test Mode:

- BoardInputTestModeistodisplaysaspeciedinputafterakeypress.

How to Enter:

- ToentertheBoardInputTestMode,presstheExtraRinsekeyduringServiceMode.

Board Input Test Mode:

1. ActivatetheServiceModerst.

2. PressthekeytostartBoardInputTest.

3.TurntheJog-DialsothatthenormalcourseLEDisturnedon,andTheWaterTemperaturewillbe

displayedinCelsius.

4.TurntheJog-DialsothattheHeavydutycycleLEDisturnedon,TheWaterTemperaturewillbe

displayedinFahrenheit.

5.TurntheJog-DialsothatthePermPresscycleLEDisturnedon,Thedoorstatuswillbedisplayed

(OPifopen,CLifclosed).

6. TurntheJog-DialsothatSanitizeLEDisturnedon,TheDoorLockSwitchstatuswillbedisplayed

(ULifunlocked,LOiflocked).

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

[BIGBANG]Technical_information-03207A-03_EN.indd 10 2013-7-16 17:15:07

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Samsung Rondelle

Samsung

Samsung WF431AB Manuel utilisateur

Samsung

Samsung WW7 T4 Series Manuel utilisateur

Samsung

Samsung WF1704WSE2/XEU Manuel utilisateur

Samsung

Samsung WW10H8 series Manuel utilisateur

Samsung

Samsung WW9 T Series Manuel utilisateur

Samsung

Samsung WA50U1 Manuel utilisateur

Samsung

Samsung WF350ANR/XAA Manuel utilisateur

Samsung

Samsung WF455ARGSWR/AA Manuel

Samsung

Samsung WF45H6300 Manuel utilisateur

Samsung

Samsung WA11J673 Series Manuel utilisateur

Samsung

Samsung WA11M8700 Series Manuel utilisateur

Samsung

Samsung WA16CG6745 Series Manuel utilisateur

Samsung

Samsung WA15J673 Series Manuel utilisateur

Samsung

Samsung WW7 A Series Manuel utilisateur

Samsung

Samsung WT8202 Manuel utilisateur

Samsung

Samsung WB25H7 Series Manuel utilisateur

Samsung

Samsung WA400 AA Series Manuel utilisateur

Samsung

Samsung WF0500NXW/XEH Guide de référence

Samsung

Samsung WF45H6300AG/A2-01 Manuel utilisateur

Samsung

Samsung WF8604 Manuel utilisateur

Samsung

Samsung WD7702R8C Manuel utilisateur

Samsung

Samsung WW9*K6 series Manuel utilisateur

Samsung

Samsung WW7 T3 Series Manuel utilisateur

Samsung

Samsung WA54R7600A Series Manuel utilisateur

Manuels Rondelle populaires d'autres marques

Tricity Bendix

Tricity Bendix AW 1000 W Guide produit

Panasonic

Panasonic NA-F60L5WRB Manuel utilisateur

GE WSLP1500 Manuel

Electrolux

Electrolux EWF1284EDW Manuel utilisateur

Bosch

Bosch WAN2829BSN Manuel utilisateur

LG TV2516DV3B Manuel utilisateur

LG TH2517DSAV Manuel utilisateur

VESTEL

VESTEL CMH-XL 7510 TE Manuel utilisateur

AEG

AEG 74335 Manuel d'utilisation

Johnson

Johnson JWF721A Manuel utilisateur

Beko

Beko WTE7604XLW0 Manuel utilisateur

Danby

Danby DTT100A1WDB Instructions de montage

Amica

Amica WA 14 Ex Manuel utilisateur

Daewoo

Daewoo DWD-F1222 Manuel utilisateur

Bosch

Bosch WAS28461AU Manuel utilisateur

Miele

Miele PW 6080 Vario Manuel utilisateur

Finlux

Finlux FLX108CF220 Manuel utilisateur

Whirlpool

Whirlpool 3LBR5132AN0 Manuel utilisateur