Samsung WA45H7200A Manuel

WASHING MACHINE

Technical Information

Code No. : DC68-03132G-01_EN

• Duetopossibilityofpersonalinjuryorpropertydamage,alwayscontactanauthorized

technicianforservicingorrepairofthisunit.

• RefertoServiceManualfordetailedinstallation,operating,testing,troubleshooting,and

disassemblyinstructions.

Models : WA48H7400A*

WA45H7200A*

WA45H7000A*

AllsafetyinformationmustbefollowedasprovidedinServiceManual.

CAUTION

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

WA7000HA WASH_WA48H_TECH MANUAL_DC68-03132G-01_EN.indd 1 2014-1-6 15:56:26

ALIGNMENT AND ADJUSTMENTS

GENERAL ERROR FUNCTION

Error Code

(Diagnostic Code

Error Image)

Description Corrective Action

1 5E Thewaterlevelfailstodropbelowthe

ResetWaterLevelwithin30minutes.

Goto“WillNotDrain”

TroubleshootingSection.

2 dE1 DoorfailstoUnlockAfter7attempts. Goto“WillNotUnlock”

TroubleshootingSection.

3 4E

Whenthellingcontinuesformore

than60minutesorthereisnochangeof

waterlevelfor5minutes.

Goto“NoWaterFill”

TroubleshootingSection.

4 dE1 Doorfailstolockafter7attempts. Goto“WillNotLock”

TroubleshootingSection.

5LE

AwaterlevellowerthantheResetwater

levelisdetectedfor5secondsduring

theWash/Rinsecycle.

Goto“NoWaterFill”

TroubleshootingSection.

61E

WaterLevelSensorTrouble.(Whenthe

inputsignalfromthewaterlevelsensor

isoutofrange,theunitwillsendout

beepingsoundsandhaltsthecycle.)

Goto“NoWaterFill”

TroubleshootingSection.

7OE

Afaultisdetectedinthewaterlevel

sensor.Data(frequency)shows

thewaterlevelisatorabovethe

overowwaterlevel.(Whenthis

conditionisdetected,themachinewill

automaticallystartdrainingwateruntil

thewaterlevelfallsbelowthereset

waterlevel)

Firstchecktoseethatallofwater

valvesarenotstuck.Ifthewater

valvesareOK,checkwaterlevel.

8UE Unbalanceorcabinetbumpisdetected

duringnalspin.

Goto“WetClothes”

TroubleshootingSection.

9 dE Doorisdetectedasopenwhileitis

tryingtolockthedoor.

Goto“QuickTestMode”andthen

doDoorLock/UnlockTest.

10 tE

Thisoccurswhenthewatertemperature

sensorfaultisdetectedcontinuously

for5seconds.

Goto“BoardInputTest”and

checkWaterTemperature.Check

looseorpinchedwires.Replace

PCBorthermistor.

11 3E

MICOMisattemptingtodrivethemotor

butisnotgettinganyresponsesignals

fromthehallsensor.Visualcheckshows

motorisnotrunning.(Locked,Defective

HallSensororOverload)

Evaluatewireharnessforlooseor

unhookedconnections.Goto“

QuickTestMode”andtestMotor.

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

WA7000HA WASH_WA48H_TECH MANUAL_DC68-03132G-01_EN.indd 2 2014-1-6 15:56:26

ALIGNMENT AND ADJUSTMENTS

Error Code

(Diagnostic Code

Error Image)

Description Corrective Action

12 4E Thehot/coldwaterhoseconnectionis

notcorrect.

Pleaseconnectthehot/cold

waterhoseconnectioncorrectly.

13 SUd

Sudsisdetectedduringthewashing

session.(“SUd”or“Sd”isnotanerror.

Whenitnisheswashing,Endandthe

“SUd”or“Sd”codewillblinkinturn.)

Guideausertoreduceamount

ofdetergentusage.

14 AE

CommunicationerrorbetweenSUBPBA

andMAINPBA.

CheckMainPBA,SUBPBA&

Wire-harness.ReplacePCB.

8E1

8E2

IftheMEMScommunicationerroror

MEMStroublediagnosiserroroccur,this

messagewillbedisplayed.

1.ChecktheMEMSsensorand

PBA.

2.Checkthewireconnector

terminals.

16 bE2 AbuttonexceptthePowerbuttonis

continuallypressed.

Checkwhethereitherthe

Powerswitchoratactswitchis

continuallypressed.

17 4E2 Thehot/coldwaterhoseconnection

isnotcorrect.

Pleaseconnectthehot/cold

waterhoseconnectioncorrectly.

18 PE

(ClutchMotorError)

Thiserroroccurswhentheposition

oftheclutchisnotdetected.

-Ifthepositiondetectionsignalis

notreceived15secondsafterthe

clutchmotorstarts,thespindrumis

shakenleftandrightandthenthe

motorisrestarted.

Ifthemotorpositionsignalisnot

receivedevenafter3reattempts,a

PEerroroccurs.

1.Checktheclutchmotor.

2.Checktheassemblystatusof

theclutchmotor.

3.Checkthewireconnector

terminals.

PE1

(clutchhallsensor

error)

Afterthecompletionoftheclutch

positiondetection,andtheclutch

hallsignalisinvalid,thespindrum

isshakenleftandrightandthenthe

clutchhallsignalisevaluatedagain.

This,iftheclutchhallsignalisstill

invalid,theclutchpositionswitching

statusischeckedandthenthe

operationisrestarted.

(Ifthe15reattemptsfail,thiserror

occurs.)

1.Checktheclutchhallsensor.

2.Checkthewireconnector

terminals.

3.Checktheclutchswitching

status.

-Checkthecouplingassembly

anddisassemblystatus.

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

WA7000HA WASH_WA48H_TECH MANUAL_DC68-03132G-01_EN.indd 3 2014-1-6 15:56:26

ALIGNMENT AND ADJUSTMENTS

TEST MODE

Test Mode:

EachTestModeisasfollowsinthecomingpages.

Thetestmodesaremodesunabletogetan

accessoncethewashingcyclehasstarteddueto

safetyreasons.

Quick Test Mode

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

WA48H7400A*

WA45H7200A*

WA45H7000A*

WA7000HA WASH_WA48H_TECH MANUAL_DC68-03132G-01_EN.indd 4 2014-1-6 15:56:27

ALIGNMENT AND ADJUSTMENTS

Denition of Quick Test Mode:

- CheckoperationofallLED’s(VerifyfaultyLED).

- Checkmodelandsoftwareversion.

- Checkdierentoperatingmodes(e.g.watervalve,motor,door,drainpump,etc.).

How to Enter:

- Plugintheunit.

- PressSpinkey,SoillevelkeyandPowerKeyatthesameTime.

Quick Test Mode:

1. AllLED’slightupanditsendsoutBeepSoundwhenit

entersintotheQuickTestMode.(Including7-Segment)

2. DisplayssoftwareversionforasecandClearEEPROM.

3. Whentheversionisdisplayed,turntheJog-Dialsothat

theversiondisappears.Pressthefollowingkeystotestthe

variouscomponents.

-Temp.Key:WaterValveTest

-DelayEndKey:DoorLock/UnlockTest

-Spin:DrainPump/CirculationPumpTest

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

WA7000HA WASH_WA48H_TECH MANUAL_DC68-03132G-01_EN.indd 5 2014-1-6 15:56:27

ALIGNMENT AND ADJUSTMENTS

Continuous Run Mode

Denition of Continuous Run Mode:

- WillcontinuouslyrepeatthecurrentcycleuntiltheContinuousRunModeiscancelled.

How to Enter:

- PressDelayEnd+Temp.Keytogetherfor5sec.

Continuous Run Mode:

1. Press

DelayEnd+

Temp.Keyfor5secduringPowerOnState(NormalUserMode).

OnceinContinuousRunMode,Thesevensegmentswillnolongerdisplay“0000”andwillalternate

betweendisplayingthenumberofcyclesofthecompletedcourseandtheremainingtimeofthecourse.

3. TheContinuousRunModewillrepeatthepreviouscycleuntilcontinuousrunmodeiscancelled.

DuringContinuousRunMode,pressDelayEnd+

Temp.

Keyfor5sectoreturntonormalusermode.

Thesevensegmentswillnolongerdisplaythenumberofcyclesandwilldisplaythemaintenance

timeonly.

5. IfyouexitServiceModeafterenteringitfromContinuousMode,thewashingmachinereturns

toContinuousMode.

6. IfpowerislostinContinuousRunMode(thatis,whenthepowerplugisdisconnectedorthe

Powerkeyispressedturningthewashingmachineo),themodeisreleasedwhenthewashing

machineisturnedonagain.

Service Mode

Denition of Service Mode:

- ServiceModeenablesservicetechnicianstoverifytheoperationofthewashingmachineand

dotroubleshooting.

- ServiceModecanbeenteredduringallwashingcyclewithoutinterruptingthecycleexcept

someoftestmodes.

- VarioustestscanbedonewithServiceMode.So,troubleshootingcanbedonebasedonthe

resultingdiagnosticcodes.

How to Enter:

- ToentertheServiceMode,presstheDelayEndandPreSoakKeyfor3secondsoruntiltheunit

sendsoutbeepingsounds.

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

Delay End + Temp.

WA7000HA WASH_WA48H_TECH MANUAL_DC68-03132G-01_EN.indd 6 2014-1-6 15:56:27

ALIGNMENT AND ADJUSTMENTS

Service Mode

Service Mode:

1.ThewashermustbeontogointotheServiceMode.

2.Themotorspeedwillbedisplayedwhenstarted(Itdisplays0whenthemotordoesnotspin).

3.Thepresentstateofthemachinewillnotbechanged.

(i.e.,thecurrentcycleinprogresswillnotbeinterruptedandonlythedisplaywillchange)

4. ToexitServiceMode,pressDelayEndandPreSoakKeyfor3secondagain,orPowerKey.If

nokeyisoperatedduringServiceModefor5minutes,themachinewillreturntonormaluser

mode.

Quick Spin Test Mode

Denition of Quick Spin Test Mode:

- QuickSpinTestModeistodoSpinCheck.(HighRPM)

How to Enter:

- DuringServiceMode,presstheDelayEndandSelfCleanKeyfor3secondstoenterQuickSpin

TestMode.

- Cannotenteroncethewashingcyclehasstarted.

Quick Spin Test Mode:

AsitentersintotheQuickSpinTestMode,itstartsspinningandreachesitsmaximumRPM.

OncetheSpinspeedreachesthemaximumRPM,thespeeddropsimmediately.

ToholdQuickSpinTestMode(enteringHoldSpeedMode),presstheStart/Pausebutton.Ifthe

Start/PausebuttonispressedduringQuickSpinTestMode,itwillstopacceleratingandholdits

spinningspeedfor10minutesbeforegoingbacktoQuickSpinTestMode.

Also,tocanceltheholdandallowQuickSpinTestModetocontinue,presstheDelayEndandSelf

CleanKeytogetherfor3seconds.

IfyouholddowntheDelayEndandSelfCleankeyforthree(3)secondswhenthewashing

machineisnotinHoldSpeedMode,QuickSpinModeisexitedandServiceModeisrestored.

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

Delay End + Pre Soak

Delay End + Self Clean

While it is not in Hold Speed Mode

Delay End + Self Clean

3 sec

While a cycle is not running

Delay End + Self Clean

for 3 sec or after 10 minutes

WA7000HA WASH_WA48H_TECH MANUAL_DC68-03132G-01_EN.indd 7 2014-1-6 15:56:28

ALIGNMENT AND ADJUSTMENTS

Cycle Count Check Mode

Denition of Cycle Count Check Mode:

- CycleCountCheckModeistotallyupthenumberofwashings.

How to Enter:

- ToentertheCycleCountCheckMode,pressthePreSoakKeyduringServiceMode.

Cycle Count Check Mode:

1. ActivatetheServiceModeinadvance.

2.WhenthePreSoakkeyispressed,thetotalnumberofwashingswilllightupandasignalLED

willglow.

3.Themaximumnumberofcycleswillbe1999.

Thecounterwillrolloverto0andstartcountingagainafter1999.

4.Thecountingwillbecarriedoutattheendofthenormalcycle.

(FornormalandContinuousRuncycles,thecountiscarriedoutattheendofthecycles.

5. ToexittheCycleCountCheckMode,pressthe“PreSoak”keyagain.

S/W Version Check Mode

Denition of S/W Version Check Mode:

- S/WVersionCheckModeistobringupS/WVersioninformation.

How to Enter:

- ToentertheS/WVersionCheckMode,presstheSoilLevelKeyduringServiceMode.

S/W Version Check Mode:

1. ActivatetheServiceModeinadvance.

2. PresstheSoilLevelKeytobringupitssoftwareVersion.

3. ToexittheS/WVersionCheckMode,presstheSoilLevelS/Wonceagain.

Then,itreturnstotheServiceModewithmotorRPMilluminating.

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

WA7000HA WASH_WA48H_TECH MANUAL_DC68-03132G-01_EN.indd 8 2014-1-6 15:56:28

ALIGNMENT AND ADJUSTMENTS

Fast Time Down Test Mode

Denition of Fast Time Down Test Mode:

- FastTimeDownTestModeistoforwardtheprogramtothenextcyclestage.

How to Enter:

- ToentertheFastTimeDownTestMode,presstheTemp.keyduringServiceMode.

Fast Time Down Test Mode:

1. ActivatetheServiceModeinadvance.

2. Toforwardtheprogramtothenextcyclestage,presstheTemp.key.

Board Input Test Mode

Denition of Board Input Test Mode:

- BoardInputTestModeistodisplaysaspeciedinputafterakeypress.

How to Enter:

- ToentertheBoardInputTestMode,presstheSelfCleankeyduringServiceMode.

Board Input Test Mode:

1. ActivatetheServiceModerst.

2. PressthekeytostartBoardInputTest.

3.TurntheJog-DialsothattheNormalcourseisturnedon,andTheWaterTemperaturewillbe

displayedinCelsius.

4.TurntheJog-DialsothatthePermPresscourseisturnedon,TheWaterTemperaturewillbe

displayedinFahrenheit.

5.TurntheJog-DialsothattheActiveWear(WA48H7400A*,WA45H7200A*)/QuickWash

(WA45H7000A*)cycleisturnedon,Thedoorstatuswillbedisplayed(OPifopen,CLifclosed).

6. TurntheJog-DialsothattheQuickWash(WA48H7400A*,WA45H7200A*)/Spin(WA45H7000A*)

cycleisturnedon,TheDoorLockSwitchstatuswillbedisplayed(ULifunlocked,LOiflocked).

7. TurntheJog-DialsothattheSpin(WA48H7400A*,WA45H7200A*)/Rinse+Spin(WA45H7000A*)

cycleisturnedon,TheWaterFrequencywillbedisplayed.

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

Self Clean

WA7000HA WASH_WA48H_TECH MANUAL_DC68-03132G-01_EN.indd 9 2014-1-6 15:56:28

ALIGNMENT AND ADJUSTMENTS

Diagnostic Code Check Mode

Denition of Diagnostic Code Check Mode:

- DiagnosticCodeCheckModeistobringupthestoreddiagnosticcodes(referecodesforservice

technicians).

How to Enter:

- ToentertheDiagnosticCodeCheckModewithcode“d”ashing,presstheSpinkeyduring

ServiceMode.

Board Input Test Mode:

1.ActivatetheServiceModerst.

2. Pressthe“Spinkey”keytostartErrorCodeCheckModewithCode“d”ashing.

3. Tocyclethroughtheerrorcodes,turntheRotaryCycleSelectorinonedirection(either

ClockwiseorCounterclockwise).

4. Now,whenturningtheRotarySelectorKeyinthesamedirection,itshowserrorcodesfromthe

latest.

5. Whenturningitintheoppositedirection,itshowstheerrorcodesinthereverseorder.

Toavoidriskofelectricalshock,personalinjuryordeath;disconnectpowertowasher

beforeservicing,unlesstestingrequirespower.

WARNING

Service Mode Spin Diagnostic Code

WA7000HA WASH_WA48H_TECH MANUAL_DC68-03132G-01_EN.indd 10 2014-1-6 15:56:28

Autres manuels pour WA45H7200A

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Samsung Rondelle

Samsung

Samsung WF8802RPZ Manuel utilisateur

Samsung

Samsung WW70K4 Series Manuel utilisateur

Samsung

Samsung WF407ANW/XAA Manuel utilisateur

Samsung

Samsung WF0602WKE/XEO Guide de référence

Samsung

Samsung WT6500 Manuel utilisateur

Samsung

Samsung DC68-02154A Manuel utilisateur

Samsung

Samsung WA45K7600AW/AA Manuel utilisateur

Samsung

Samsung WW1 B Series Manuel utilisateur

Samsung

Samsung WD90J7 series Manuel utilisateur

Samsung

Samsung WT10 Manuel utilisateur

Samsung

Samsung WD6102CKC Manuel utilisateur

Samsung

Samsung WF0600NBE/YLV Manuel utilisateur

Samsung

Samsung WA90T6250B Series Manuel utilisateur

Samsung

Samsung WT12J4200MB/SG Manuel utilisateur

Samsung

Samsung WW6 M2 Series Manuel utilisateur

Samsung

Samsung WF45N5300A Series Manuel utilisateur

Samsung

Samsung WA22M8700 Series Manuel utilisateur

Samsung

Samsung H146HWB Manuel utilisateur

Samsung

Samsung WF9 F5 Series Manuel utilisateur

Samsung

Samsung WT14J4200MB/AP Manuel utilisateur

Samsung

Samsung WM1245A Manuel utilisateur

Samsung

Samsung WA50M7450AP/A4 Manuel utilisateur

Samsung

Samsung WF218ANS Manuel utilisateur

Samsung

Samsung WF405 A2 Series Manuel utilisateur

Manuels Rondelle populaires d'autres marques

Tricity Bendix

Tricity Bendix AW 1000 W Guide produit

Panasonic

Panasonic NA-F60L5WRB Manuel utilisateur

GE WSLP1500 Manuel

Electrolux

Electrolux EWF1284EDW Manuel utilisateur

Bosch

Bosch WAN2829BSN Manuel utilisateur

LG TV2516DV3B Manuel utilisateur

LG TH2517DSAV Manuel utilisateur

VESTEL

VESTEL CMH-XL 7510 TE Manuel utilisateur

AEG

AEG 74335 Manuel d'utilisation

Johnson

Johnson JWF721A Manuel utilisateur

Beko

Beko WTE7604XLW0 Manuel utilisateur

Danby

Danby DTT100A1WDB Instructions de montage

Amica

Amica WA 14 Ex Manuel utilisateur

Daewoo

Daewoo DWD-F1222 Manuel utilisateur

Bosch

Bosch WAS28461AU Manuel utilisateur

Miele

Miele PW 6080 Vario Manuel utilisateur

Finlux

Finlux FLX108CF220 Manuel utilisateur

Whirlpool

Whirlpool 3LBR5132AN0 Manuel utilisateur