Samsung SmartThings Vision Manuel utilisateur

SmartThings Vision

Welcome to your

Smart Light

DVS Sensor

Indicator LED

Function Button

USB Charging Port

Light Sensor

Holder

Installation Guide

Indoor installation is recommended. Avoid installing in wet or humid place, otherwise it

may cause malfunctions.

Avoid installing in high temperature environment or near a radiator, heating device,

stove, and other heat sources (including an ampliﬁer).

This product must be attached to ﬂat and clean wall surface. Remove the ﬁlm on the

tape before use. In addition, holder can be attached to iron surface or furniture by

utilizing magnet on the holder.

Avoid installing on the appliances that generate vibration, such as refrigerator or air

conditioner. Otherwise it may cause malfunctions.

Since this product connects to WI-FI, please avoid installing it near devices that emit

strong EM waves.

In the event of device fails to operate:

Please unplug the power cable and plug again after1 minute.If this status persists,

press and hold the function button for more than 7 seconds to reset the device.

Reset takes several minutes. Please do not unplug the power cable before indicator LED

status alternately ﬂashes green and red light.

Trouble Shooting

Recommended

installation height ：

1.5m ~ 1.7m

In the event of Internet is disconnected:

The indicator light shows red. Please check your internet connection.

In the event of app fails to operate:

Please re-start the app. If this status persists, please visit www.SmartThings.com.

1.5m~1.7m

Power on Green On

Green Blinking System boot

Setting standby status Alternately ﬂashes

green and red light

Setting error Red Blinking

Person detected Yellow Blinking for 3 seconds

Function error

Network error

Red Blinking

Red On

Error

Status

Power off No light

LED Status Indicator

※

After login，select “+", and add

device.

Connect your phone to WI-FI where device is used, and

download SmartThings App.

SmartThings

2. 3. Select "SmartThings", in the

"All brands" tab.

Plug the power cable, and wait LED

indicator ﬂashes green and red

alternately.

4. 6.5.

After click “Vision sensor”，select “SmartThings Vision”. After setup location for your

SmartThings Vision, click next.

7. Scan the QR code on the device,

as shown in the picture.

If QR code on device or package

is damaged or fell off, device

will be unable to setup. Please

keep QR code safe.

8. The installation will begin after

scanning QR code.

9. After the installation is ﬁnished,

completion status is as shown in the

picture.

Connecting to Vision sensor

Plug yourVision sensor into an outlet

and wait until the left light starts

blinking green and red.

Add yourdevice by scanning its

QR code.

The code or serial numbermay be on the

back of the device or in the instruction

booklet.

Enter serial number instead

※

My home

Kitchen >

Living room >

No devices

Add device

All brands

SmartThings

Auto detect

SmartThings

vision sensor

My home-Living room

Successfully connected

SmartThings Vision

SmartThings

vision sensor

Vision sensor

SmartThings Vision

Select a location for yourVision sensor.

My home

Add new location

Autres manuels Samsung Caméra de sécurité

Samsung

Samsung SHC-740N/P Manuel utilisateur

Samsung

Samsung SCC-B5344 Manuel utilisateur

Samsung

Samsung iPolis SNP-5200H Manuel utilisateur

Samsung

Samsung SCC-B53X Series Manuel utilisateur

Samsung

Samsung SCD-6021 Manuel utilisateur

Samsung

Samsung SCC-B2007P Manuel utilisateur

Samsung

Samsung SNP-6320 Manuel utilisateur

Samsung

Samsung SCO-2080 Manuel utilisateur

Samsung

Samsung SNV-7080N Manuel utilisateur

Samsung

Samsung SCC-C6407(P) Manuel utilisateur

Samsung

Samsung SCC-641 - 22x Zoom Smart Dome Camera Manuel utilisateur

Samsung

Samsung SCP-2371 Manuel utilisateur

Samsung

Samsung SCB-3020 Manuel utilisateur

Samsung

Samsung SCC-B5393 Manuel utilisateur

Samsung

Samsung SNB-1000 Manuel utilisateur

Samsung

Samsung SHC-735 Manuel utilisateur

Samsung

Samsung SNP-6321H Manuel utilisateur

Samsung

Samsung SMARTCAM SNH-E6440BN Manuel utilisateur

Samsung

Samsung SCP-3370TH Manuel utilisateur

Samsung

Samsung SVD-4300 Manuel utilisateur

Samsung

Samsung SCC-B5367 Manuel utilisateur

Samsung

Samsung SCP-2273 Manuel utilisateur

Samsung

Samsung Beyond SCB-5003 Manuel utilisateur

Samsung

Samsung SCO-2370 Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur

Lumens

Lumens VC-A50PNW Manuel utilisateur