Samsung AC-505CM Series Manuel

LED R&D Lab(VD)

LED Display Install Manual

IAC Series

LH015IAC***

Ver. 0.3

LED R&D Lab(VD)

Revision History

Version Date (Y/M/D) Description

0.1 2023/06/01 Release ver 0.1

0.2 2023/06/12 Modification Side by Side Content (P114~118)

Delete Side by Side Screen Split scenario #2 (P119)

0.3 2023/06/15 Add checking CABINET number (BNV20231FE9) (P18,20)

LED R&D Lab(VD)

1. Product and installation information

2. Preparation of Cabinet installation

3. Wall Mount

4. Frame installation and cable connection

5. Frame Bezel Installation

6. Dehumidification mode guide

7. IP Manual setting Guide

※ Appendix1 -LED MODULE and CIRCUIT replacement method

※ Appendix2 –System Main / TCON / LED Module Update data on replacement

※ Appendix3 –Side by Side installation

※ Appendix4 –LSM connection

※ Appendix5 –Gradation Calibration (SSA)

※ Appendix6 –Framelock mode support timing table

Table of contents

LED R&D Lab(VD)

MODEL Product appearance and information

IAC series

REMARK IAC Series : Package Type / 60 Hz Refresh Rate

◆Model specification

-This manual is an installation manual for IAC and can be applied to the model below.

1. Product and installation information

LED R&D Lab(VD)

◆Model specification (IAC)

Specifications

130”

P1.5

CABINET

Size

(mm)

Horizontal 2888.55

vertical 1628.55

Resolution

(Pixels)

Horizontal 1920

vertical 1080

Module (EA) 27 X 4 (108)

weight (kg)

(Cabinet) 16.0

SET weight (kg) 124.55

Packing weight (kg) 78.9

Power consumption (W) Typical 685W (Max 1660W)

Luminance (nit)

Max 500

Peak 1000

1. Product and installation information

LED R&D Lab(VD)

◆Cabinet product information

1628.55

62.2

130”

2888.55

1. Product and installation information

LED R&D Lab(VD)

◆Installation precautions (LED damage)

precautions Image

[External impact, fall caution]

1 Remove the cover-corner of the product before installation and do not

impact the LED surface or drop it on the floor.

2 Do not place the product on the vibrator and do not place the LED

surface facing the floor.

3 Make sure that the edge of the LED module is not damaged by external

contact.

4 Do not load more than 12 steps.

① ②

③ ④

[Watch out for LED damage caused by static electricity]

▶Do not work by touching the LED surface with hands without gloves.

[Caution of LED damage caused by metal]

▶Be careful not to get metal on the front of the LED.

▶When attaching the metal, separate the module and remove it using a

magnet.

MODULE

Front

metal

1. Product and installation information

LED R&D Lab(VD)

precautions Image

[Caution of LED damage caused by liquid]

When water or various chemicals touch the LED, the inside of the LED may be damaged.

①Water, dew, air conditioner condensate, sprayer, sweat, and saliva do not directly touch the

product.

-Be careful not to sweat on the product. (※ Maintain proper temperature so as not to sweat)

-Be careful not to spit on the product, and it is recommended to wear a mask.

②The following substances should not be directly in contact with the product, and

the case of exposure of the steam to the product should be minimized.

-Detergent or disinfectant : carpet cleaning detergent, glass cleaner, 84 disinfectant, etc.

(※ When cleaning the floor or wall with detergent or water, it is recommended to install a screen so that it does not touch the

product)

-Various chemicals: paints, mosquito repellents, cinnabar, benzene, toluene, solvents, surfactants, halogens (chlorine, bromine),

and substances containing these ingredients;

③If liquid touches the product

-If there is water on the product, turn off the product immediately, dry it enough for more than a day, and run the

dehumidification mode to remove moisture from the LED. (※ P74, refer to "Dehumidification mode using LSM")

-If there is any liquid other than water on it, remove it with alcohol and run the dehumidification mode.

[Precautions related to construction]

①In the case of installation at the construction site, the product must be installed after construction and

cleaning are completed.

②If the product is under construction in the installed space, take the following measures.

-Shielding film should be installed to protect the product by sealing the entire product so that it is not exposed to dust and

various liquids.

-Operates a video or 100 gray scale white for more than 2 hours every day.

-After the construction is completed, remove enough dust, various liquids, and steam, remove the shield, and execute the

dehumidification mode.

카펫

클리너 유리

세정제

Taping Shielding film

Disinfectant

※ Only use for IWA

◆Installation precautions (LED damage)

1. Product and installation information

LED R&D Lab(VD)

◆Heat dissipation guide

Installation condition

-Conditions for using SAMSUNG WALL MOUNT

-Solar direct sunlight conditions cannot be installed (including glass window passage conditions)

-It is recommended to use room temperature below 25°C

-Effect of Cold/Hot Air Conditioning System

-When cold / hot air is the same air conditioning system,

∙Be careful not to let the warm air touch the product.

-Outside temperature measurement position

Measured at a distance of 300mm from the center of the product

Air vent aperture ratio

-use mesh type air vent

-If the aperture ratio is not 100%, the separation distance =

Minimum distance

aperture ratio(%) /100

-aperture ratio (%) =    .  ℎ

  

※ It is written based on Full white, back light 7

Video, created based on back light 10

wall

Outside

temperature

measurement

position

300mm

1. Product and installation information

LED R&D Lab(VD)

•Vertical wall installation (if Fan is not applied)

WALL

Air vent area

minimum 30mm

set ~ ceiling

set ~ floor

1. Product and installation information

minimum 30mm

Autres manuels pour AC-505CM Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Samsung Moniteur

Samsung

Samsung SyncMaster P64FP Manuel utilisateur

Samsung

Samsung SyncMaster 70S Manuel utilisateur

Samsung

Samsung DP15HS Manuel utilisateur

Samsung

Samsung SUR40 Manuel utilisateur

Samsung

Samsung MO17W Series Manuel utilisateur

Samsung

Samsung 305T - SyncMaster - 30" LCD Monitor Manuel utilisateur

Samsung

Samsung C27H711QE Series Manuel utilisateur

Samsung

Samsung SyncMaster 2043SW Manuel utilisateur

Samsung

Samsung Esa PDP4294LV Manuel utilisateur

Samsung

Samsung SyncMaster 240MP Manuel utilisateur

Samsung

Samsung DM82E-BR Manuel utilisateur

Samsung

Samsung SMO-152QN - Monitor + Camera 4 Manuel utilisateur

Samsung

Samsung CJ79 Series Manuel utilisateur

Samsung

Samsung F2080 - SyncMaster - 20" LCD Monitor Manuel utilisateur

Samsung

Samsung RM49H Manuel utilisateur

Samsung

Samsung PS-42C91H Manuel utilisateur

Samsung

Samsung LS27R650FDUXXU Manuel utilisateur

Samsung

Samsung SyncMaster 400BX Manuel utilisateur

Samsung

Samsung SyncMaster LD220G Manuel utilisateur

Samsung

Samsung SyncMaster 931CW Manuel utilisateur

Samsung

Samsung SyncMaster S24C450DW Manuel utilisateur

Samsung

Samsung SyncMaster UD55A Manuel utilisateur

Samsung

Samsung SyncMaster LD190N Manuel utilisateur

Samsung

Samsung Odyssey Neo G7 S43CG70 Series Manuel utilisateur

Manuels Moniteur populaires d'autres marques

Linear Acoustic

Linear Acoustic LQ-1000 Manuel utilisateur

AOC

AOC I2579V Manuel utilisateur

Gateway

Gateway FPD1520 Manuel utilisateur

Furuno

Furuno Mu 120c Manuel utilisateur

Asus

Asus VB171D - 17" LCD Monitor Manuel utilisateur

Dell

Dell S2230MX Instructions d'utilisation

Philips

Philips 107C64 Manuel utilisateur

Dell

Dell S2409WFP Manuel utilisateur

EverFocus

EverFocus EN-7517E Manuel utilisateur

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuel utilisateur

Dell

Dell Precision 7680 Mode d’emploi

LG 50PM1M - - 50" Plasma Panel Manuel utilisateur

Bosch

Bosch DDU 9 Manuel utilisateur

Acer

Acer A231HL Manuel utilisateur

Philips

Philips 86BDL4152T Manuel utilisateur

NEC

NEC AccuSync LCD5V Manuel utilisateur

Emay

Emay SleepO2 Manuel utilisateur

IBM

IBM 6360 Instructions d'installation