Salind Salind 01 Manuel utilisateur
2
Read the instructions carefully before using the GPS tracker
for the first time. Keep the instructions somewhere safe
in case you may need it in the future. However, do not
hesitate to contact us if you have any problem or doubt
via Whats App, chat or email.
… for ordering our GPS Tracker!
Thank you very much, Contents
2
3
1. Scope of delivery ......................................4
2. Product description ..................................5
3. Activation .............................................6
4. Startup operations....................................7
5. Installation ............................................8
6. Turning on ...........................................10
7. Use ...................................................11
8. Meaning LED lights ................................. 12
9. Technical data ....................................... 13
10. Safety instructions .................................14
11. Instructions for disposal of used batteries ..........19
12. Instructions for disposal of electrical devices ....... 21
Contents
3
4
The scope of delivery includes:
Salind 01
M2MSIM card (already in place, not interchangeable)
Cable harness
Velcro fastener with adhesive strip on the back
Scope of delivery
1.
Product description
4
5
LED Signals
SIM Card
(already in place, not
interchangeable)
Product description
2.
5
SIM Card Slot
2.
3.
4.
1.
3.
1.
2.
4.
Cable harness
connection
6
In order to start using your Salind GPS tracker, first you will have to
activate it online. Please enter the following link:
Activation
3.
Startup operations
NOTE!
To activate you need the device ID. Please make a note before
installing your GPS tracker.
www.start.finder-portal.com
You also find further details of the activation pro-
cess in the following link:
https://www.youtube.com/watch?v=r3t7ugoiXVQ
(You may use the subtitle option on YouTube in
order to translate audio).
6
7
Please observe the following points before connecting the device
to the vehicle battery:
•The SIM card is already in the Salind 01.
•The Salind 01 should not be attached to fuel lines or other
combustible components.
•No other components of your vehicle should be damaged by the
attachment.
•Installing the Salind 01 on the vehicle to power the device may discharge
the vehicle‘s battery. Before connecting, check whether your vehicle
has a discharge protection and retrofit it if necessary (in idle mode,
the GPS tracker requires approx. 10-20 mAh).
Startup operations
4.
7
8
Installation
1. Connect the Salind 01 to the cable
harness using the black plug-in function.
2. Connect the device to the battery.
The red cable with the fuse to Plus (+).
The black cable to Minus (-).
5.
Please proceed as follows when connecting the GPS tracker to
your car battery. The following figure serves as a guide.
8
9
ATTENTION!
The poles must never be reversed.
NOTE!
When connected to the power supply, the Salind 01 switches
on immediately and the LED lights emit a signal.
9
Red cable
Black cable
-
+
-
+
Battery
9-75V
10
After conecting and starting the GPS tracker
for the first time, we recommend moving the
device for a couple minutes. The best option
is to drive for some kilometers in order for the
device to make the first connection to the best
possible network.
Turning on
After a successful activation you can switch on the Salind 01.
By connecting the GPS tracker to the power supply the
device has already been switched on.
6.
10
Autres manuels pour Salind 01
1
Table des matières
Autres manuels Salind GPS
Salind
Salind PET Tracker Manuel utilisateur
Salind
Salind 08 Manuel utilisateur
Salind
Salind 11 4G Manuel utilisateur
Salind
Salind 20 4G USA Manuel utilisateur
Salind
Salind OBD Manuel utilisateur
Salind
Salind GPS-Tracker 08 Manuel utilisateur
Salind
Salind 2020 Manuel utilisateur
Salind
Salind BIKE Manuel utilisateur
Salind
Salind GPS-TRACKER 06 Manuel utilisateur
Salind
Salind Salind 01 Manuel utilisateur
