Sage Oracle SES980 Manuel utilisateur

the Oracle™

SES980

CONTENTS

2 Sage®Recommends Safety First

5 Know your new appliance

7 Operating your new appliance

17 Care & cleaning

23 Troubleshooting

SAGE®

RECOMMENDS

SAFETY FIRST

At Sage®we are very safety

conscious. We design and

manufacture consumer

products with the safety of

you, our valued customer,

foremost in mind. In

addition we ask that you

exercise a degree of care

when using any electrical

appliance and adhere to

the following precautions.

IMPORTANT

SAFEGUARDS

READ ALL INSTRUCTIONS

BEFORE USE AND SAVE

FOR FUTURE REFERENCE

• The full information

book is available at

sageappliances.com

• Before using for the rst

time please ensure that your

electricity supply is the same

as shown on the rating label on

the underside of the appliance.

If you have any concerns

please contact your local

electricity company.

• Remove any packaging

material and promotional labels

or stickers before using the

Oracle™ for the rst time.

• To eliminate a choking hazard

for young children, remove and

safely discard the protective

cover tted to the power plug

of this appliance.

• Do not place the product near

the edge of a bench or table

during operation. Ensure the

surface is level, clean and free

of water and other substances.

• Do not let the cord hang over

the edge of a bench or table,

or become knotted. Keep

away from hot gas or electric

burner, or where it could touch

a heated oven.

• Appliances can be used by

persons with reduced physical,

sensory or mental capabilities

or lack of experience and

knowledge if they have been

given supervision or instruction

concerning use of the appliance

WE RECOMMEND SAFETY FIRST

in a safe way and understand the

hazards involved.

• Children shall not play with

the appliance.

• Regularly inspect the

supply cord, plug and actual

appliance for any damage. If

found damaged in any way,

immediately cease use of

the appliance and return the

entire appliance to the nearest

authorised Sage Service Centre

for examination, replacement

or repair.

• Keep the appliance and

accessories clean. Follow the

cleaning instructions provided

in this book. Any procedure not

listed in this instruction booklet

should be performed at an

authorised Sage Service Centre.

• The installation of a current

device (safety switch) is

recommended to provide

additional safety protection

when using electrical

appliances. It is advisable that

a safety switch with a rated

residual operating current not

exceeding 30mA be installed in

the electrical circuit supplying

the appliance. See your

electrician for professional advice.

SPECIFIC INSTRUCTIONS

FOR SES980 THE ORACLE™

• This appliance is

recommended for household

use only. Do not use this

appliance for any purpose

other than its intended use.

Do not use in moving vehicles

or boats. Do not use outdoors.

• If the appliance is to be:

- left unattended

- cleaned

- moved

- assembled; or

- stored

Always switch O the espresso

machine by pressing the Power

button to O, switch O at the

power outlet and unplug.

• Ensure the product is properly

assembled before rst use.

• Do not use any other liquid

apart from cold mains/town

water. We do not recommend

the use of highly ltered,

de-mineralised or distilled

water as this may aect the

taste of the coee and how the

espresso machine is designed

to function.

• Ensure the portalter is rmly

inserted and secured into the

group head before starting

an extraction. Never remove

the portalter during the

extraction process.

• Do not touch hot surfaces.

Allow the product to cool down

before moving or cleaning

any parts.

• Use caution after milk texturing

as the ‘Auto Purge’ function

may purge hot steam when the

steam wand is lowered.

• Use caution when operating

machine as metal surfaces are

liable to get hot during use.

• Use caution when using the

de-scale feature as hot steam

may be released. Before

de-scaling, ensure drip tray is

empty and inserted. Refer to

page 21 for further instructions.

• Heating element surface

is subject to residual heat

after use.

SPECIFIC INSTRUCTIONS

FOR WATER FILTER

• Filter cartridge should be kept

out of reach of children.

• Store lter cartridges in a dry

place in the original packaging.

• Protect cartridges from heat

and direct sunlight.

• Do not use damaged

lter cartridges.

• Do not open lter cartridges.

• If you are absent for a

prolonged period of time,

empty the water tank and

replace the cartridge.

The symbol shown

indicates that this appliance

should not be disposed of

in normal household waste.

It should be taken to a local

authority waste collection centre

designated for this purpose or to

a dealer providing this service.

For more information, please

contact your local council oce.

To protect against electric

shock, do not immerse

the power cord, power plug

or appliance in water or any

other liquid.

WE RECOMMEND SAFETY FIRST

SAVE THESE INSTRUCTIONS

KNOW YOUR NEW APPLIANCE

A. Integrated conical burr grinder

B. Top-ll 2.5L removable water tank

C. Grind Size dial

D. Grind LCD

E. Main LCD

F. 1 CUP and 2 CUP buttons

G. Grind outlet

H. Heated 58mm group head with

I. 58mm full stainless steel portalter

J. Drop down swivel foot

K. Heated cup warming tray

L. HOT WATER button

M. LONG BLACK dial

N. Steam lever

O. Steam LCD

P. SELECT dial

Q. Cool touch steam wand

R. Dedicated hot water outlet

S. Descale access point

T. Tool storage tray

U. Removable drip tray

KNOW YOUR NEW APPLIANCE

A. Stainless steel milk jug

B. 2 cup lter basket

C. 1 cup lter basket

D. Water lter holder with lter

E. Cleaning disc

F. Mini grinds bin

G. Burr brush

H. Grind outlet brush & tamp removal magnet

I. Cleaning tool for steam wand tip

J. Allen key

K. Steam wand cleaning powder

L. Water hardness test strip

M. Espresso cleaning tablets

ACCESSORIES

Rating Information

220–240V~50–60Hz 2000–2400W

OPERATING YOUR NEW APPLIANCE

BEFORE FIRST USE

Machine Preparation

Remove and discard all labels and packaging

materials attached to your espresso machine.

Ensure you have removed all parts and

accessories before discarding the packaging.

Clean parts and accessories (water tank,

portalter, lter basket, jug) using warm water

and a gentle dish washing liquid. Rinse well

then dry thoroughly.

TIP

To easily manoeuvre your machine, use

the drop down swivel foot located under

the drip tray.

INSTALLING THE WATER FILTER

• Remove the water lter and water lter

holder from the plastic bag.

• Soak the lter in cold water for 5 minutes.

• Wash the lter holder with cold water.

• Set the reminder for next month

of replacement.We recommend

to replace the lter after 3 months.

• Insert the lter into the two parts of the

lter holder.

• To install the assembled lter holder into

the water tank, align the base of the lter

holder with the adapter inside the water tank.

Push down to lock into place.

• Fill the water tank with cold water before sliding

back into position at the back of the machine

and locking into place.

FIRST USE

1. Ensure tank is lled with cold water.

2. Press POWER button to turn machine on.

3. The main LCD will display 'Hrd3', prompting

you to set the water hardness level.

Setting Water Hardness

• Dip the test strip into a sample of the water

you have lled the tank with. Wait for one

minute.The water hardness setting is

indicated by the number of red squares

displayed on the test strip.

• Rotate SELECT dial to the required

setting from 'Hrd1' (softest water) to 'Hrd5'

(hardest water). Press SELECT dial to set.

4. After approximately 5 minutes, the machine

will reach the default operating temperature

93˚C and all 6 buttons will illuminate.

The machine is now in STANDBY mode.

TEMP TEXTURE

SELECTPOWER

HOT WATER LONG BLACK

OPERATING YOUR NEW APPLIANCE

Flushing The Machine

When the machine has reached STANDBY mode:

1. Press 2 CUP button to run water through

the group head for 30 seconds.

2. Press HOT WATER button to run

water through the hot water outlet.

After 30 seconds, press HOT WATER

button again to stop the ow of water.

3. Lift steam lever to the MANUAL position

to release steam through the steam wand.

After 30 seconds, lower the steam lever

to the centre OFF position.

4. Repeat steps 1–3 twice.

MANUAL will ash on LCD

The machine will not reach operating temperature

(STANDBY mode) if the steam lever is in the

MANUAL position.The steam LCD will display

'MANUAL'. Lower the steam lever to the centre

OFF position.

Steam operation is ready when the SELECT

dial illuminates.

NOTE

You will not be able to select the 1 CUP,

2 CUP or LONG BLACK functions; or access

the cleaning cycle in the menu options until the

machine has reached operating temperature

(STANDBY mode).

GRINDING OPERATION

Insert bean hopper into position on top of

the machine.Turn knob to lock into place.

Fill hopper with fresh beans.

SELECTING GRIND SIZE

There are 45 espresso grind size settings

(No. 1 – nest, No. 45 – coarsest) to enable you

to select the right grind size for your coee beans

and achieve the perfect espresso extraction.

We recommend you start at No. 30 and adjust

as required to control espresso ow rate.

SELECT YOUR FILTER BASKET

Use the 1 Cup Filter Basket for making a single

cup or a weaker tasting espresso.

Use the 2 Cup Filter Basket for making 2 cups

or a stronger tasting espresso, usually for mugs

or larger cups.

AUTO GRIND DOSE & TAMP

Align portalter handle with the INSERT position on

the grind outlet. Lift to insert portalter into the grind

outlet and rotate to the centre position.

GRIND OUTLET

GROUP HEAD

CENTRE

POSITION

GRIND OUTLET

To start the auto grind, dose & tamp function, rotate

the portalter to the right then gently guide back to

the centre position. Grinding will commence.

When the auto grind, dose & tamp function

is complete, rotate the portalter handle

to the INSERT position and lower to remove.

OPERATING YOUR NEW APPLIANCE

ESPRESSO EXTRACTION

Align portalter handle with the INSERT position

on the group head. Lift to insert portalter into the

group head and rotate towards the LOCK TIGHT

position until resistance is felt.

EXTRACTION GUIDE

The 1 CUP button and 2 CUP button

use duration to control espresso volume.

The duration times are preset, but can be

reprogrammed.

1 CUP BUTTON

Press 1 CUP button once to extract a single shot

of espresso.

2 CUP BUTTON

Press 2 CUP button once to extract a double shot

of espresso.

The machine will stop after 2 CUP duration has

been extracted and will return to STANDBY mode.

EXTRACTION

TYPES

GRIND SHOT

DURATION

OVER-EXTRACTED

(bitter • astringent)

To o

Fine

Over

45secs

BALANCED Optimum Between

15-40secs

UNDER-EXTRACTED

(underdeveloped • sour)

To o

Coarse

Less than

15secs

MANUAL OVERRIDE

Press and hold either the 1 CUP or 2 CUP

button to commence pre-infusion.When the

required pre-infusion duration is met, release the

button to begin full pump pressure.

Press the button again to stop the pour when

required duration has been achieved.

TEXTURING MILK

The SELECT dial is used to select milk

temperature and texture. Press the dial to toggle

between milk temperature and texture.

ADJUSTING MILK TEMPERATURE

Press the SELECT dial until the milk temperature

ashes. Rotate the dial to increase or decrease

milk temperature.

STEAM

SELECTSELECTSELECT

TEMP TEXTURETEMP TEXTURETEMP TEXTURE

ADJUSTING MILK TEXTURE

Press the SELECT dial until the milk texture

triangle ashes. Rotate dial towards 'CAPP'

for more texture or 'LATTE' for less texture.

STEAM

SELECTSELECTSELECT

TEMP TEXTURETEMP TEXTURETEMP TEXTURE

NOTE

Prior to texturing milk, always purge steam

wand by momentarily pressing down the

steam lever.

AUTO MILK TEXTURING

If machine is run continuously for 30 minutes,

allow machine to cool for 5 minutes before

each use.

PRESET LONG BLACK

There are 3 preset Long Black settings – small,

medium and large.To use one of these settings:

1. Insert the 2 Cup Filter Basket into the

Porta-lter.

2. Fill the portalter using the auto grind,

dose & tamp function.

3. Insert the portalter into the group head.

4. Position your cup so the portalter spouts

and hot water outlet are directed inside

the cup.

5. Rotate the LONG BLACK dial to the

desired cup size.

PRESET CUP SIZE AMOUNT BREWED

Small Approx. 180ml

Medium Approx. 240ml

Large Approx. 355ml

The brewed amounts are approximate only.

Actual amounts may vary due to the coee bean

roast, blend and freshness as well as the selected

grind size. These factors aect extraction rate and

shot volume.

6. To start extraction, press the LONG

BLACK dial. Espresso will extract from the

portalter spouts, followed by hot water

from the hot water outlet.

MANUAL LONG BLACK

Start with fresh cold milk. Fill milk jug to below the

spout position. Lift steam wand and insert into milk

jug. Lower steam wand, ensuring it is fully down.

The milk jug should rest on the drip tray and milk

should cover the steam wand seal.

MIN

MAX

To start, press down and release steam lever. Milk

texturing will stop automatically when the selected

milk temperature is reached. Lift steam wand

to remove milk jug. Wipe the wand and tip with

a damp cloth. Lower steam wand to the down

position and the wand will automatically purge.

MANUAL MILK TEXTURING

Auto milk texturing and auto shut-o are disabled

during manual milk texturing mode.

Insert steam wand into milk jug. Lift steam lever to

activate manual steam mode. Once the desired

milk texture and temperature are achieved, lower

the steam lever to the centre OFF position. Wipe

the wand and tip with a damp cloth. Lower

steam wand to the down position and the wand will

automatically purge.

CAUTION: BURN HAZARD

Pressurised steam can still be released,

even after machine has been switched o.

Children must always be supervised.

NOTE

OPERATING YOUR NEW APPLIANCE

Table des matières

Autres manuels Sage Cafetière

Sage

Sage Barista Touch BES880 Manuel utilisateur

Sage

Sage the Oracle Touch BES990 Manuel utilisateur

Sage

Sage the Oracle Manuel utilisateur

Sage

Sage SES810 Manuel utilisateur

Sage

Sage Duo-Temp Pro BES810 Manuel utilisateur

Sage

Sage Bambimo SES450 Manuel utilisateur

Sage

Sage Barista Express BES875 Manuel utilisateur

Sage

Sage the Dual Boiler BES920 Manuel utilisateur

Sage

Sage Precision Brewer SDC400 Manuel utilisateur

Sage

Sage Bambino Plus SES500 Manuel utilisateur

Sage

Sage Oracle Touch SES990BST Manuel utilisateur

Sage

Sage the Bambino SES450BSS4GUK1 Manuel utilisateur

Sage

Sage Duo-Temp Pro BES810 Manuel utilisateur

Sage

Sage Smart Grinder Pro BCG820 Manuel utilisateur

Sage

Sage Barista Touch SES880BTR Manuel utilisateur

Sage

Sage Dual Boiler Manuel utilisateur

Sage

Sage the Dual Boiler BES920 Manuel utilisateur

Sage

Sage Oracle Touch SES990 Manuel utilisateur

Sage

Sage Nespresso Vertuo Creatista Manuel utilisateur

Sage

Sage the Barista Pro SES878 Manuel utilisateur

Sage

Sage Precision Brewer SDC400 Manuel utilisateur

Sage

Sage the Barist Express SES875 Manuel utilisateur

Sage

Sage BES980UK Manuel utilisateur

Sage

Sage the Dual Boiler BES920 Manuel utilisateur

Manuels Cafetière populaires d'autres marques

Taurus

Taurus Livorno 6 Manuel utilisateur

Delta-q

Delta-q QUICK Manuel utilisateur

Bunn

Bunn LCA-1 Guide de dépannage

Black & Decker

Black & Decker BLACK DECKER HOME DE790 Instructions d'installation

Saeco

Saeco Vienna Plus Sup 018M Manuel utilisateur

DeLonghi

DeLonghi DC300 Manuel utilisateur

INCAPTO

INCAPTO BXCO1470E Manuel utilisateur

Bosch

Bosch TASSIMO finesse TAS16B Series Manuel utilisateur

Exido

Exido 245-072 Manuel utilisateur

Animo

Animo OptiVend Choco Manuel utilisateur

Siemens

Siemens TQ505DF Series Manuel utilisateur

DeLonghi

DeLonghi ECI341 Manuel utilisateur

Krups

Krups KT406511 Manuel utilisateur

Cimbali

Cimbali M32 Classic Manuel utilisateur

Philips

Philips HL3844N Manuel utilisateur

Bosch

Bosch TES 515 SERIES Manuel utilisateur

Tekmatix

Tekmatix TMFM - 65 Manuel utilisateur

Scarlett

Scarlett SC-CM33005 Manuel utilisateur