SAFARI Montage SD/HD MPEG Digital Encoder Instructions de montage

SAFARI MONTAGE®

SD/HD MPEG DIGITAL ENCODER™

INSTALLATION AND SETUP GUIDE

SD/HD MPEG Digital Encoder | G1571 Standalone

QUAD SD/HD MPEG Digital Encoder | G1572 Rack Mount

SAFETY PRECAUTIONS

The presence of this symbol is to alert the installer and user to the presence of uninsulated dangerous voltages

within the product’s enclosure that may be of sufficient magnitude to produce a risk of electric shock.

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS DEVICE TO

RAIN OR MOISTURE, AND DO NOT OPEN THE DEVICE. REFER SERVICING TO QUALIFIED

PERSONNEL ONLY.

•DO NOT apply power to the device until all connections have been made, all components have been installed

and all wiring has been properly terminated.

•DO NOT terminate, change or uninstall any wiring without first disconnecting power from the device.

•Use only the supplied 12VDC power supply with the center pin positive or power cord. The use of any other

power supply or cord may cause damage and void the warranty.

•The device must be installed in an environment consistent with its operating temperature specifications.

Placement next to heating devices, ducts or areas of high humidity is to be avoided, as doing so may cause

damage and void the warranty.

•DO NOT cover any of the device’s ventilation openings.

•If the device has been in a cold environment, allow it to warm to room temperature for at least 2 hours before

connecting power.

Product Description

SAFARI Montage®SD/HD MPEG Digital Encoders™ provide a powerful and ultra-reliable, “out of the box”

solution for your entire IP Television, digital signage and digital media encoding and distribution requirements.

G1571 Standalone SD/HD MPEG Digital Encoder G1572 Quad SD/HD MPEG Digital Encoder

SAFARI Montage®SD/HD MPEG Digital Encoders™ encode incoming digital or analog video to deliver an

MPEG-4 H.264 or MPEG-2 network stream over the IP network to any SAFARI Montage®user, SAFARI

Montage®Digital Signage or Classroom Media Controller (CMC) and provide efficient remote management via

an integrated, password-protected, embedded web server.

Both the G1571 Standalone and G1572 Quad SD/HD MPEG Digital Encoders offer flexible video input options,

supporting HDMI, component and composite inputs, and SD through HD resolutions ranging from 480i to

1080p.

The compact G1571 standalone unit is ideal for single source server room, office or classroom use, while the

G1572 quad rack-mount encoder model is designed for server room or “head end” use.

This manual describes the setup and use of both the G1571 standalone and G1572 quad rack-mount models.

Unpacking and Inspection

Ensure that all items are removed and inspected prior to discarding any packing material.

Thoroughly inspect the unit and all contents to make certain all components are present and no damage has

occurred in shipping, paying particular attention to connectors. If there is any sign of damage to the unit or items

are missing, please contact SAFARI Montage Technical Support. SAFARI Montage Technical Support is

available Monday – Friday from 8 a.m. to 6 p.m. Eastern Time, and they may be contacted by telephone at 800-

782-7230 or online via http://www.safarimontage.com/support/.

Package Contents

•G1571 Standalone SD/HD MPEG Digital Encoder with:

o(1) 12V Power Adapter

o(1) 6’ RJ45 Cat-5E Patch Cable

o(1) 6’ YPbPr Component Video Cable

o(1) 6’ Video + Stereo Audio Composite Cable

o(1) 6’ HDMI Cable

•One G1572 Quad SD/HD MPEG Digital Encoder with:

o(1) Power Cord

o(4) 6’ RJ45 Cat-5E Patch Cable

o(4) 6’ YPbPr Component Video Cable

o(4) 6’ Video + Stereo Audio Composite Cable

o(4) 6’ HDMI Cable

SAFARI Montage®SD/HD MPEG Digital Encoder™Specifications

Video Input

HDMI 1.4 Digital – 480i to 1080p

Component YPbPr – 480i to 1080i

Composite CVBS – 480i

Video Encoding

H.264 SD - Supported bit rates 1 - 4 Mbps

H.264 HD - Supported bit rates 2 - 10 Mbps

MPEG-2 SD - Supported bit rates 2 - 8 Mbps

MPEG-2 HD - Supported bit rates 10 - 20 Mbps

Unicast, Multicast and DNLA Streams

Audio Input

HDMI, Digital Stereo Audio

Dual RCA, Analog Stereo Audio

G1571 Standalone only

Coaxial (S/PDIF RCA), Digital Stereo Audio

Optical (S/PDIF TOSLINK), Digital Stereo Audio

Audio Encoding MPEG-4 ACC; 128, 256 and 384 kbps

MPEG-1 Layer 2; 128, 256 and 384 kbps

Management Configuration/Remote Status Monitoring Via On-Board Web Server

Software Updates

Remotely Upgradeable Via Web Interface

G1571 Standalone only

USB Via Front Panel USB Port

Windows Vista®

Windows 7®

Windows 8®

MAC OS X®v10.6 – 10.9

Network 10/100/1000 Base-T Ethernet

Power 12VDC @ 1.5 A – G1571 Standalone

12VDC @ 3A – G1572 Quad Rack-Mount

Dimensions 9.3" (W) x 6.1" (D) x 1.4" (H) – G1571 Standalone

17.5" (W) x 7.2" (D) x 1.75" (H) – G1572 Quad Rack-Mount

Included

6' RJ45 Cat-5e Patch Cable

6' YPbPr Component Video Cable

6' Dual RCA Audio Cable

6' HDMI Cable

Note: G1572 Quad Rack-Mount Contains Four (4) Sets

Warranty 3 Years

SAFARI Montage®SD/HD MPEG Digital Encoder™Front Panel

Buttons/LEDs

(Each encoder on the G1572 has one of the

following buttons/LEDs unless otherwise

noted)

Description

Reboot button Reboots the Device (Unsaved Settings Will be Lost)

RST / UPG button To Reset All the Settings of the Device to Factory Default:

1. Disconnect Power.

2. Press and Hold the RST/UPG Button, then Connect Power.

3. Hold the Button Until CFG LED Flashes 10 Times (about 10 seconds).

4. After the CFG LED Stops Flashing, Release the RST/UPG Button.

To Upgrade Firmware Using the USB Port (G1571 Only):

1. Disconnect Power.

2. Plug in the USB Drive Containing the Firmware Upgrade.

3. Press and Hold the RST/UPG Button, then Connect Power to Boot-Up the Encoder.

4. The USB LED Will Flash While Copying the Firmware Image from USB Drive (About

3-5 Seconds).

5. Wait Until the CFG LED Stops Flashing.

6. Release the RST/CFG Button, and Wait for the Device to Reboot and Upgrade the

Firmware (About 1 Minute).

7. Reset the Cache on your Browser After Upgrading the Firmware.

NOTE: The Firmware May Also be Upgraded by Uploading the Firmware Image Via the Web

UI Administration Page.

PWR Indicates that the Device is Powered

CFG Indicates that the Device is in Configuration Mode

USB Indicates that a USB Drive is Mounted (G1571 only)

MPEG-2 Indicates that the Device is Encoding Video in MPEG-2 Format

AVC Indicates that the Device is Encoding Video in H.264/MPEG-4 Part 10/AVC Format

MP2 Indicates that the Device is Encoding Audio in MPEG-1 Layer 2 Format

AAC Indicates that the Device is Encoding Audio in AAC Format

AC-3 Indicates that the Device is Encoding Audio in AC-3 Format

Installation and Configuration

Please read these instructions in their entirety before you begin:

•Review any questions with Technical Support in advance. Please note that SAFARI Montage Technical

Support is available Monday – Friday from 8 a.m. to 6 p.m. Eastern Time, and they may be contacted by

telephone at 800-782-7230 or online via http://www.safarimontage.com/support/.

SAFARI Montage®System Requirements:

•SAFARI Montage®v5.8.x

•SAFARI Montage® Media Player v5.9.x with VideoLAN VLC Media Player v2.03 32-bit

•SAFARI Montage® Digital Signage Controller Software v6.0.x

Before You Begin:

•Make all connections before powering the encoder.

•Note that all G1571 standalone encoders ship with a default static IP address of 191.53.51.207.

•Note that all G1572 quad encoders ship with the following default static IP addressing scheme.

o191.53.51.207 – 1st encoder

o191.53.51.208 – 2nd encoder

o191.53.51.209 – 3rd encoder

o191.53.51.210 – 4th encoder

•If using UPnP/DLNA, all devices, including the encoder, SmartTV and the configuration PC, should be

located within the same local network segment.

•SAFARI Montage strongly recommends that video sources be connected directly to the SD/HD MPEG

Digital Encoder with the supplied cabling. SAFARI Montage cannot provide support for third-party

distribution and/or switching equipment placed inline between the video source and the encoder.

•The encoder is designed to work with input sources set to 30 or 60 FPS. Please make certain your video

source equipment is set for 30 or 60 frames per second.

Initial Network Configuration:

1. Connect the encoder to an isolated network switch for configuration.

2. Connect a PC to the network switch, and configure the PC with an IP address in the 191.53.51.xxx subnet,

e.g., 191.53.51.10.

oBe certain to avoid assigning the PC the default encoder IP address (191.53.51.207).

3. Power the encoder via the supplied power adapter or cord.

4. Configure the network settings as required to conform to the local network addressing scheme.

a. All encoders ship with a default static IP address of 191.53.51.207.

b. Open a web browser and navigate to http://191.53.51.207:8888 to view the encoder

Overview page.

c. Click on Network Setup to configure the network settings and login with the

default credentials:

Username: admin

Password: Admin123

d. Set the encoder Hostname, IP address and network configuration as required to unique values that

conform to the local network address scheme.

5. If configuring multiple encoders, repeat the process for each unit, assigning a unique IP address and

hostname to each encoder.

6. Once networking configuration is complete, reconfigure the client PC to the local network addressing

scheme, confirm the encoder(s) may be reached via http://[New IP Address]:8888 and

continue configuration.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels SAFARI Montage Convertisseur de média

SAFARI Montage

SAFARI Montage G3011 Instructions de montage

Manuels Convertisseur de média populaires d'autres marques

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuel utilisateur

SPROLINK

SPROLINK VA1 Manuel utilisateur

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuel utilisateur

Nikon

Nikon AF-S TC-20E III Manuel utilisateur

Axis

Axis AXIS Q7406 Manuel utilisateur

Omega

Omega TAC80B-J Manuel utilisateur

Zoom

Zoom Thunderbolt TAC-2R Manuel utilisateur

OST

OST iConverter 10/100M Manuel utilisateur

Vertiv

Vertiv Netsure Manuel utilisateur

birddog

birddog MINI Manuel utilisateur

Roland

Roland GI-10 Manuel utilisateur

Wallenstein

Wallenstein WX310 Manuel utilisateur

Pace

Pace MSS 200-1 Manuel utilisateur

Solar Converters

Solar Converters EQ 12/24-50 Manuel utilisateur

CYP

CYP EL-7400V Manuel utilisateur

TIE

TIE MIDI 1i1o Manuel utilisateur

DCS

DCS Vivaldi Upsampler Manuel utilisateur

Westermo

Westermo MCW-211 SERIES Manuel utilisateur