Saab 32 025 902 Manuel utilisateur
Saab 9-3
900 Installation instructions
SCdefault
MONTERINGSANVISNING ·INSTALLATION INSTRUCTIONS
MONTAGEANLEITUNG ·INSTRUCTIONS DE MONTAGE
SITdefault
Saab 9-3
Parking assistance (SPA)
4D, see page 2-13
5D, see page 14-30
CV, see page 31-42
Accessories Part No. Group Date Instruction Part No. Replaces
32 025 902
32 025 903
32 025 904
32 026 045 9:40-08 May 07 32 025 940 32 025 940 Oct 06
F930A042
2 32025940
Saab 9-3
4D
1 SPA control module
2M03-07: Holder (x4)
3M03-07: Seal (x4)
4M03-07: Distance sensor (x4)
5M03-07: Decor strip, bumper
6 Wiring harness, distance sensor
7 SPA wiring harness
8 Dust cover
9 Cable tie (x8)
10 M08: Tape
The following parts must be ordered separately
M08: Hole-punching tool
M08: Distance sensor (x4)
M08: Holder (x4)
F930A626
1
9
5
7
6
2
3
4
8
10
32025940 3
Saab 9-3
1 Open the boot lid.
2 Turn the ignition key to the OFF position and
remove the key. Raise the car.
3 Remove the two nuts holding the rear bumper
air shield against the body and the two bolts
holding the bumper shell against the wheel
housings.
4 Lower the car.
5M03-07: Remove the decor strip from the rear
bumper.
F930A627
3
3 3
5
4 32025940
Saab 9-3
6M03-07: Raise and fold aside the luggage com-
partment floor and remove the luggage com-
partment scuff plate.
7 Remove the panel in the luggage compartment
side trim.
8M03-07: Remove the side scuff plates.
9 Remove the clips and fold aside the side trims
on the left and right-hand sides.
10 Remove the rear lamp clusters.
F930A628
810
9
9
10
6
6
32025940 5
Saab 9-3
11 M03-07: Remove the bolts for the bumper shell
which are located under the rear lamp clusters.
12 Remove the bumper bolts at the wheel hous-
ings.
13 M08: Release the bumper's upper mounting by
the rear lamp clusters.
14 Remove the bumper shell by pulling the sides
outwardsand then pulling the bumper shell rear-
wards.
Important
Place the bumper on a soft, clean surface.
F930A629
11
14
12
13
6 32025940
Saab 9-3
15 Remove the console in which such equipment
as a CD changer/amplifier may be fitted. Dis-
connectthe connectionsto any equipmentin the
console.
16 Remove the connector for the rear harness
(blue) from the fuse box. Unplug connector A1
from the blue connector. Remove the lock.
17 Fit the kit's wiring harness. Fit the red cable to
connector A1 in position 1. Fit the green cable to
connector A1 in position 4.
18 Fit the lock. Plug connector A1 into the blue con-
nector.
WARNING
Certain cars: The visible red light is a class 1
laser. Do not look directly into the optical fibre or
the control module connector at close range. A
distance of less than 20 mm between your eyes
and the light source may cause eye injury.
F930A630
17
16,18
16
16,18
32025940 7
Saab 9-3
19 Remove the rubber plug from under the left-
hand rear lamp cluster.
20 Connect the ground cable.
21 Connect the control module and fit it into the
slots on the rear fuse box.
22 Position the wiring harness and secure with
cable ties.
F930A631
19
22
22
22
22 21
20
8 32025940
Saab 9-3
23 Remove the support from the bumper shell.
24 M03-07: Align the bumper shell's decor strip
using the guide tab and press in the hooks start-
ing in the centre and then continuing out to the
sides.
25 M03-07: Fit the seals on the sensors.
26 M03-07: Fit the distance sensors and holders
together.
27 M03-07: Fit the distance sensors into the decor
strip mountings.
28 M03-07: Fit the wiring harness for the sensors in
the bumper shell groove.
29 M03-07: Fit the support to the bumper shell.
Important
The connector sockets for the distance sensors
should point towards the right-hand side of the car.
F930A632
25
26
27 23,29
28 28
28
32025940 9
Saab 9-3
30 M08: Drill 8 mm holes (from the inside of the
bumper shell) in the centre of each marking
(x 4).
Position the hole-punching tool from the outside
of the bumper. Grip on the outside, at the same
time tighten the nut from the inside until the
hole-punching tool is pressed through the whole
of the bumper shell. Carry out the hole-making
procedure for all four holes.
Fit the tape and holders for the sensors in
accordance with the markings in the bumper
shell.
Important
The connector sockets for the distance sensors
should point towards the right-hand side of the car.
F930A633
10 32025940
Saab 9-3
31 M08: Fit the wiring harness in the support forthe
bumper shell.
32 M08: Fit the support to the bumper shell.
WARNING
Check that the wiring harness is not pinched.
Incorrect fitting can damage the wiring harness
and cause a short-circuit/fire.
F930A634
31
32
Ce manuel convient aux modèles suivants
3
Autres manuels Saab Automobile électronique
Saab
Saab 12 832 509 Manuel utilisateur
Saab
Saab 32 026 005 Manuel utilisateur
Saab
Saab 32 025 603 Manuel utilisateur
Saab
Saab 33 000 573 Manuel utilisateur
Saab
Saab 12 787 887 Manuel utilisateur
Saab
Saab 32000574 Manuel utilisateur
Saab
Saab 32 025 687 Manuel utilisateur
Saab
Saab 32 025 686 Manuel utilisateur
