S4A EL-250 Manuel utilisateur
300
92
58
Electromagnetic Lock Installation Instructions
Dimensions
Specifications
Accessories
1. Suitable for in-swing door or 90 doors
2. Built-in push button and power indicator light.
Adjustable door opening time (0~9 seconds.)
3. Build-in delay time and lock monitor output.
4. Armature with handle design.
5. Standalone operation when power is on and it
does not need to be controlled by proximity
reader.
6. Install at the center of the door leaf to prevent
deformation whenever it is locked or unlock.
1
Unit: mm
Plate 1
5 32Screw 9
Power Supply 15%
DC 12V / DC 24V
Operation Delay Time
Operation temperature
5%
Hall Effect Sensor
450mA / 12VDC 235mA / 24VDC
Out-swing door and In-swing door
600lbs
35 5 ( 30 room temperature)
The warranty is 1 years under normal circumstances
N.O / N.C
0 sec., 2.5sec., 5sec., 9sec.
Application
Holding forces
Warranty
Weight 3 kg
Current
Monitor Output
Model
Item
Features
VER 17.11.30
EL-250 Notes
Installation
Step 1:
Please stick the sticker on the desired mounting position (Please refer to Fig.1) and drill holes
according to the sticker's indicated positions. Remove the sticker after drilling a hole for wiring.
Step 2:
Remove both sides of the lock's covers A and pull out the B.(Please refer to Fig.2- Fig.4)
Use screws to screw the body lock tight on the appropriate position. Place all covers back in order.
2
Control Panel Voltage and Delay Time Adjusting
N.C
COM
N.O
P.S
V-
V+
LED
Door open
switch
Wiring hole
Delay time
switch
Voltage
adjusting Jump
Indicator light
Door
Frame
Alignment
sticker
Drilling
positions
Wiring hole
Fig1
Drilling positions
Screws
Screws
Wiring
hole
Fig2 Fig3
Fig4
A
B
1. Door open buttons have both built-in and external inputs. Please use both V- and P.S. Points
for external door open button. Both built-in and external door open buttons are able to be
used at the same time. (Please refer to the diagram above) .
2. Door Lock status (N.O/N.C) as Relay output. Maximum load of 1A@24VAC.
3. Indicator light is green when the door is locked, or else the door did not close tight.
Attention
Adjusting Volatge
P.S
V -
External door open
push button Delay time Setting
Step 5
Slide plate(P) in when positioning and adjusting screws are tighten. Assemble the handle and its
body's back in order.
Step 3:
Remove the upper cover (C) of the handle and then the lower cover(C-1) by removing two screws
(A-1 B-1) to pull out plate(D).(Please refer to Fig5-Fig6)
Step 4:
Use two attached screws to screw the handle onto the appropriate position of the installation holes
when D is pulled out.(Please refer to Fig 7) Do not screw tight as to adjust both handle and body
lock positions well by closing the door for several times to make sure both of them are matched.
Screw the remaining three screws when they are matched.
3
PLeft opening door
Installation diagram
Fig8
Fig7
Fig6
Fig5
B
A
C
Screws
Screws
B-1
A-1
C-1
D
Adjusting to the
right and left.
Installing handle
4
Optional plate
Optional EL-250P plate (thickness of 3.6mm) is available to achieve optimum height of both door
frame and door leaf when the unit is installed.
Door is not locked light.
Q & A
2. Check if the voltage is set correctly. Any dust or rust will affect the operation of the lock.
1. Check if the armature is mounted to the correct position.
1. Check if the voltage is correct. 2. Check if the setting of voltage is correct.
3. Check if the magnetic lock and armature are engaged lightly.
Indicator light is unable to show green light when door is closed.
Maintenance of the magnetic lock.
1. Any dust or rust should be removed regularly.
2. Lubricant should be apply on the magnetic lock to avoid any rust depending on
the environment it is installed (such as at the seaside).
Right opening door
P
EL-250P
EL-250P
Door
Frame
Door
Leaf
Table des matières
Autres manuels S4A Verrouillage
