S2Konnect N-2020SX Manuel utilisateur
S2Konnect N-2020SX
S2Konnect N-2020SX
1000Base-SX Dual Port Server Adapter,
PCI-X, 2 Fiber LC
User Manual
2
S2Konnect N-2020SX
3
Copyright © S2Konnect GmbH, 2010. All rights reserved.
This manual refers to the S2Konnect N-2020SX 1000Base-SX Dual Port Server Adapter, PCI-X,
2 Fiber LC. Contents are subject to change without notice.
Product and brand names are (registered) trademarks of their appropriate owners.
If you have comments on this documentation, please send to:
S2Konnect GmbH
Siemensstrasse 23
76275 Ettlingen / Germany
visit our web site: http://www.s2konnect.com
S2Konnect N-2020SX
4
Conventions
The following conventions apply to this manual.
Warnings and Notes
Used to indicate a potentially hazardous situation which, if not avoided, could result in death
or serious injury. Example: dangerous voltage.
Used to indicate a potentially hazardous situation which, if not avoided, could result to a da-
mage to your eyes. Example: laser light.
Used to indicate a potentially hazardous situation which, if not avoided, may result in minor
or moderate injury. Example: electrostatic discharge.
Used for additional information and advice.
!
i
S2Konnect N-2020SX
5
Table of Contents
Conventions 4
Warning Notes 4
Safety Precautions 7
Avoiding injuries - Avoiding damage 7
1 Introduction 9
2 System requirements 9
3 Installation of the Network Adapter 9
4 Connection of the Network Adapter 11
Transmission Distances 11
Connection to the Network 11
5 Hardware Features 13
Adapter Characteristics 13
LED Displays 14
6 Testing the Network Adapter 15
DOS Diagnostic Program 15
Loopback Wrag Plug Test 15
7 Troubleshooting 17
8 Important Information 18
Technical Support 18
Returning an Adapter for Repair 18
Additional Documentation and Updates 18
Technical Specications 19
Appendix A. License and Warranty Information 22
The Americas, Asia, Australia, New Zealand, Pacic 22
Europe 23
Deutschland, Schweiz, Österreich, Lichtenstein 24
S2Konnect N-2020SX
Table of Figures
Figure 1: Insertion of the adapter into the computer
Figure 2: Connection of ber-optics cables/plugs
Figure 3: Possible network congurations / connection options
Figure 4: Location of the LEDs
Figure 5: Setup for loopback wrap plug testing
6
S2Konnect N-2020SX
7
Safety Precautions
To protect yourself from injuries and avoid damage of the device, always observe the following
safety instructions when installing the network adapter.
Avoiding injuries
Electrical current!
Electrical current from power, phone, and communications cables can be hazardous.
Never touch any electrical elements with bare hands.
To avoid potential shock hazards:
• Do not carry out any installation, maintenance, or (re)conguration work during a
thunderstorm.
• Do not connect or disconnect any power cables during a thunderstorm.
• For installation in a Hot-Plug system, observe the safety instructions specic to this sys-
tem. Read the relevant documentation rst.
• Do not connect the network adapter to a telephone line.
Electrical installations must comply with the safety regulations of the country in which they are
operated.
Avoiding damage
Electrostatic discharge!
Electrostatic discharge may damage or destroy the Network adapter.
To avoid damaging the S2Konnect N-2020SX Dual Port Server Adapter observe the following:
• Switch off the computer.
• Disconnect the power cord from the power outlet.
• Remove the computer cover.
• Before installing the network adapter, put on an antistatic wrist strap (electrically conduc-
tive).
• Connect the wrist strap to the computer chassis
Do not connect the wrist straps to the ground terminal of the power supply!
Faulty wiring could make this terminal live and potentially lethal.
• When you are ready to install the network adapter, open the antistatic bag.
• Hold the antistatic packaging of the network adapter against the bracket of an expansion
slot on your computer for at least two seconds.
This reduces the static charge in the packaging and in your body.
If you need to place the network adapter somewehre after removing it from the antistatic
bag, make sure you place it on the antistatic bag and on a level surface.
Do not place the network adapter on the computer cover or on any other metal surface.
• Cautiously insert the adapter into the corresponding slot.
Do not touch any circuits on the network adapter or any of its port contacts.
!
i
S2Konnect N-2020SX
For the N-2020SX adapter, observe the following:
Laser light!
Laser light from ber-optic transmission cables and components can damage your eyes.
The laser components on the network adapter are Class 1 laser components. Class 1 lasers are
considered incapable of producing radiation levels during normal operation or maintenance and
are, therefor, determined to be eye-safe.
To avoid damaging your eyes and to continue safe operation in case of abnormal circumstances:
• Never look directly into the outlets of ber-optic cables or ber-optic transmission compo-
nents with unprotected eyes!
• Never allow ber-optic transmission paths to operate until all the connections have been
made.
• Always t protective plugs to any unused ports on the switch or the network adapter.
Radiation!
The use of controls or adjustments or performance of procedures other than those specied herein
may result in hazardous radiation exposure.
In general, observe the following:
• Never use force when working with the network adapter or the PCI Express or PCI/PCI-X
bus.
• Do not allow anyone else to touch the network adapter.
• Avoid unnecessary movement since this can increase electrostatic charge.
!
8
S2Konnect N-2020SX
9
Introduction
Thank you for purchasing a S2Konnect product.
This document describes the installation of the network adapter card.
The N-2020SX is a PCI-X adapter which must be installed in a PCI-X slot of the computer.
The adapter contains a Network chipset “Marvell 88E8022“
System requirements
Computer System:
The N-2020SX adapter is a typical server adapter supporting high throughput of data.
You may utilize this adapter in any system supporting PCI-X.
Cable:
You must use a ber LC cable to connect the adapter. Table “Transmission distances” in chapter 4
shows the distances of transmission you can reach.
1
2
Installation of the Network Adapter
The installation procedure in Hot-Plug systems may differ from the following. For Hot-Plug sys-
tems, read the corresponding documentation. Have the computer manual ready and if necessary,
a key and screwdriver to open the cover and remove the bracket.
To install the adapter in the computer, proceed as follows:
1. Switch off the computer in wich the network adapter is to be installed.
2. Disconnect the power cord from the power outlet.
Observe the safety instructions (see page 7)
3. Open the computer cover as described in your computer manual.
You may need a screwdriver or similar tool to remove the screws from the cover.
If you are installing a network adapter in a tower computer, we recommend to put the com-
puter on its side in order to apply the correct force to insert the adapter into the PCI-X slot.
4. Consult the section in your computer manual that describes how to install expansion cards.
5. Locate a free PCI-X slot on the motherboard.
S2Konnect PCI-X adapters can be installed in (short) 32-bit or (long) 64-bit pci-x bus slot at 33
MHz, 66MHz, 100 MHz or 133 MHz. Best performance, however, is reached with a 64-bit/133 MHz bus.
6. Remove the bracket from the expansion slot (if applicable).
Follow the instruction in your computer manual.
7. Remove the network adapter from the antistatic bag.
Observe the safety instructions (see page 7).
8. Insert the network adapter into the PCI-X slot as described in your computer manual
(also see gure 1 “Insertion of the adapter into the computer“).
Make sure the network adapter is correctly aligned with the PCI-X slot on the motherboard.
9. Push the network adapter down vertically into the slot until it is rmly seated.
10. If available, tighten the locking screw on the xing bracket until the adapter is rmly connec-
ted to the computer cover (or to the attachment provided for expansion cards).
11. Replace the computer cover.
12. Replace and tighten all screws.
13. Reconnect the power supply.
Observe the safety instructions (see page 7)
3
i
S2Konnect N-2020SX
10
Figure 1. Insertion of the adapter into the computer
Table des matières
Autres manuels S2Konnect Adaptateur
