S-1 URS-0030 Manuel utilisateur
User’s Manual
Written By
Sensor research team
S-1 CORPORATION
168, S1 BUILDING,
SOONHWA-DONG, JOONG-GU,
SEOUL, KOREA
Tel: +82 1588 3112
Fax: +82 2 2131 8869
Website: www.s1.co.kr
Revised: March 2013
URS-0030
UWB Intrusion Detection Sensor
CAUTION!!
• This equipment may only be operated Indoors.
• Do not use to Outdoors.
• Do not intentionally install aimed at windows or
outside opening doors.
Table of Contents
Introduction …………………………………………………………….1
Information to the user.……………………………………………….1
Features of the UWB Sensor....……………………………………...2
Coverage of the UWB Sensor.……………………………………….3
UWB Sensor Specifications………………………………………….4
Configuration and Installation……………………………………….5
Operational precautions……………………………………………...6
UWB Intrusion Detection Sensor – URS-00301
Introduction
The UWB(Ultra Wide Band) sensors refers to a kind of radar technology that was traditionally
used in military applications. When used as a security means, it’s low power, wide band
characteristics often causes frequent false alarms. Overcoming such limitations with its
excellence in technology, S1 showcases the first ever UWB-based security sensor in the world.
Its radar-based principle makes it inherently immune to heat source-induced false alarms and
enables high level of sensitivity to the movement of heat-insulated intruders. Coverage can be
flexibly adjusted to enable its deployment in various environments.
This document describes the features and the specifications of the UWB sensor, important
regulatory information concerning its use, and details on how to diagnose potential problems.
Information to the User
The UWB sensor is an ultra-wideband(UWB) wireless device certified under FCC Part 15.517.
It’s use is subject to technical requirements for indoor UWB systems, in particular the stipulation
that the devices must only be used indoors. Users should note carefully the following
information:
• CAUTION: This equipment may only be operated indoors. Operation outdoors is in
violation of 47 U.S.C. 301 and could subject the operator to serious penalties.
• This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Users should also carefully note the following information:
• CAUTION: Any changes or modifications made to the “UWB Sensor” which are not expressly
approved by the “S-1” could void the user’s authority to operate the equipment.
• NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications, However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
2
Features of the UWB Sensor
The diagram below shows several important features of the UWB Sensor:
UWB
Antenna
Lens
LED
GB-41
(Option)
Terminal
(Power, COM)
Rotary Switch
Label
(System)
[SET]
[TOP] [BOTTOM]
Label
(Certification)
Magnetic
Switch Point
UWB Intrusion Detection Sensor – URS-0030
3
Coverage of the UWB Sensor
Maximum detection area of the sensor is as follows:
Horizontal View
Vertical View
2~3m(6.56~9.84ft)
1.5~10m(4.92~32.80ft)
UWB Intrusion Detection Sensor – URS-0030
4
UWB Sensor Specifications
The specification of the sensor refer to the following table:
Model URS-0030
Colors URS-0030W : White URS-0030A : Black
Detection Method Impulse Radio(Ultra Wide Band)
Coverage Wide: 8m x 10m(26.24 x 32.80ft), 80˚Wide
Mounting Height 2.0 ~ 3.0m(6.5 ~ 10ft)
Detection Speed 0.3 ~ 1.5m/sec.(1 ~ 5ft/sec.)
LED Alarm Indicator On
Alarm Period Approx. 2 sec.
Alarm Output N.C, 12VDC, 0.3A max.
Warm-up Period Approx. 60 sec.
Power Supply 12VDC(9.6 ~ 14.4VDC)
Current Consumption 30mA (max.) at 12VDC(9.6 ~ 14.4VDC)
Weight 85g(2.99oz)
RF
Parameters
Output Power ≤-41.3dBm
Frequency 8.5 ~ 9.5GHz
Band Width ≥500MHz at -10dB
Antenna Type Patch type
Relay
Parameters
Form From-B (Normal Close)
Type Photo-MOS
Rate 60VDC, 0.1A max.
Operating Temperature -10℃~ +50℃(+14℉~ +122℉)
Operating Humidity 95% max.
UWB Intrusion Detection Sensor – URS-0030
5
Configuration and Installation
The configuration of the sensor are as follows:
Assembly process are as follows:
1 Step - Assemble “Bottom” and “GB-41”
2 Step - Assemble “Top” and “Terminal”
3 Step - Assemble “Top” and “Bottom”
SENSOR
[TOP] [BOTTOM]
OPTION
[Bracket]
UWB Intrusion Detection Sensor – URS-0030
6
Operational precautions
• Do not apply voltages higher than the
rated voltage.
AC110V
• Do not install where pet dogs and cats.
.
• When swaying objects(mobiles of metal material),
in the detection area, change the direction or
adjust the detection distance.
• Do not install in the swaying wall.
• Do not install the outdoor. • Do not install the curtain(blind) by the external
wind swaying.
UWB Intrusion Detection Sensor – URS-0030
Ce manuel convient aux modèles suivants
2
Table des matières
