Rydeen PSR4000 Manuel utilisateur
PSR4000
PSK4
PSK4 Flush
SPK004
LED004
PSR4000 PSK4 PSK4 Flush
SPK004 LED004
Owner’s Manual
Digital Parking Sensor Systems
V1.2
- 1 -
WARNINGS
THE FOLLOWING INSTRUCTIONS ARE INTENDED FOR AUTHORIZED
RYDEEN MOBILE INSTALLERS ONLY.
Dropping any components in the system or subjecting it to excessive shock
and vibrations as this may cause it to malfunction and is not covered by
warranty.
The Control Box of the Parking Sensor System IS NOT WATERPROOF.
Avoid exposing it to rain or other forms of excessive moisture.
Water damage is not covered under the warranty.
CAN BUS Vehicles:
There is NO NEED TO CUT AN ORIGINAL VEHICLE WIRE
YOU MUST SPLICE WIRE ONLY AND OBTAIN POSITIVE POWER(+12V).
MUST CHECK BEHIND BUMPER FOR ANY METAL BRACKETS OR
INTERNAL BRACES BEFORE DRILLING
The Parking Sensor Systems are used for the rear placement only, these are
not recommended for front mounted bumpers.
The use of Rydeen Parking Sensor system should never replace normal
operational and safety precautions needed for reversing
a vehicle.
Caution should always be taken in ANY vehicle operation.
1. Kit Contents
1) PSR4000
2) PSK4
O 18.8mm
O 18.8mm
Sensor Wire
7.5ft X4
Extension Cable
13ft X4
Extension Cable
13ft X4
Sensor Wire
7.5ft X4
M
O rings X8
Speaker
10.5ft
3M Tape
- 2 -
4) SPK004
3) PSK4 Flush
1) Basic Specification
2. Technical Information
Specifications
Display Direction indicator (LED display is included )
Detecting distance
0-
8.0 feet for flat surfaces; 0-
4.0 feet for human or uneven surfaces
Sensors Universal sensors. Rear sensors instantly turn on with reverse gear
selection; Front sensors instantly turn on with brake selection.
Operating conditions
Nominal Voltage
DC 12V
Working Voltage range
DC 9V~16V
Working current
20mA 300m A~
Working Temp.
-20℃
Ultrasonic frequency
40 KHz
Others
Sensor Waterproof IP67
Installation method Drilling
Cable length 263.8inches/6700mm, with extension cables.
~+70℃
5) LED004
Extension Cable
13ft X4
Sensor Wire
7.5ft X4
H
O rings X8
Speaker
10.5ft X1
3) LED Display and Speaker Alarm Conditions
Rear sensors
(AL.BL. CR.DR./2RL. 2RR): Accurate display of distance and the correct sound tips
Detection distance
NO.Distance (unit: feet/meter)
Level definition
Display (
/Alarming sound
unit: feet)
Using buzzer only
1 6.0(1.8) 8.0(2.4)
5.0(1.5)<—≤6.0(1.8)
3.0(0.9)<—≤ 5.0(1.5)
2.5 (0.75) <—≤3.0(0.9)
1.0(0.3) ≤—≤2.5 (0.75)
<1.0 (0.3)
<—≤
6.5 8.0/NO
5.5-8.0/NO
3.5-5.0/Bi…Bi…Bi…
3.0/Bi.Bi.Bi.
1.0-2.5/Bi.Bi.Bi.
0.0/Biiii-----
-
2
3
4
Front sensors ( EL.FL.GR.HR/2FL. 2FR): Accurate display of distance and the correct sound
tips, display: feet.
Detection distance
NO.Distance (unit: feet/meter) Level definition
Display(unit: feet)
/Alarming sound
unit: feet
Using buzzer only
1
2
3
4
3.0(0.9)<
2.0(0.6)<—≤3.0(0.9)
1.0(0.3)<—≤2.0(0.6)
<1.0(0.3)
2) Wire Connection Diagram
- 3 -
Sensor wire (7.5ft) Extension wire (13ft)
5
6
Safe
Safe
Safe
Warning
Warning
Danger
NO
Bi…Bi…Bi…
Bi…Bi…Bi…
Bi…Bi…Bi…
Bi.Bi.Bi.
Biiii-----
LED Display/Speaker
Button
Additional Speaker
LED Display/Speaker
a. When brake trigger is activated (ON) and remains engaged by the foot brake, the front sensors
will be active for 20sec of detection then turn off. The detection range for front sensors is up to
3ft. When Brake trigger is a activated (On) and foot brake is detained for less than 20sec (e.g.
5s, 10s, 18s, etc.) the front sensors will continue to detect until 20secs of countdown has been
completed. If brake trigger is activated multiple times, the system will restart 20 sec countdown
after the last trigger.
Safe
Safe
Warning
Danger
NO
2.5-3.0/ Bi...Bi...Bi...
1.0-2.0 / Bi.Bi.Bi.
0.0 /Biiii-----
NO
Bi…Bi…Bi…
Bi.Bi.Bi.
Biiii-----
b. When in reverse and foot is on the brake, both the Front and Rear sensors will be active.
The front sensors will operate as mentioned above.
c. When sensors are activated during reverse. The rear sensors will remain active for the entire
duration of vehicle in reverse.
3. Painting the Sensors
1) Preparation
The sensors mounted in a paint tray come
with the rubber “O” rings already installed.
The rubber “O” rings prevent paint and
sanding dust to set inside the sensors.
Once the paint has dried replace painted
“O” rings with new “O” rings
3) Spray and paint
Apply a thin coat of paint. Let it dry then paint again for better paint coating coverage.
For PSR4000/PSK4
Paint the plastic rings together with the sensor heads.
4) After Painting the sensors, let them completely dry before installing the silicon ring
Depending on the vehicle body color , place white silicon rubber rings for a lighter
color vehicle, place black rings for a dark color vehicle.
For PSK4 Flush
Make sure the silicon rubber rings are
not installed around the sensor head
2) Sand the surface of sensors with a fine
sandpaper (1000 or 1200 grit) for
better paint adhesion. Clean the sensor
well to be free from sanding dust.
- 4 -
4. Sensor Head Angle Optional
Take the silicone ring out if already installed
Make sure that the degree marking is on the
top of the sensor
Insert the silicone
ring into the sensor
- 5 -
5. Systems Overview
For Passenger Cars
Speaker/LED Display
(2 options of sensor heads)
The brain box is installed under the
glove compartment
- 6 -
Optional Distance Display
LED004 (includes a speaker)
/SPK004 (Speaker)
The Control Box is not waterproof.
It is recommended to place it under
the driver sheet.
There are 8 LED Display Options
For Trucks
- 7 -
LED DISPLAY OPTIONS
6. Installation
1) The proper placement of the sensors is important both for appearance and for the
proper operation of the unit. Sensors should be mounted at 90 angles to the ground.
o
It is important to avoid obstructions caused by bumper shape.
2 Measure the height on a bumper for proper installation locations. )
Three installation options ：
a.4 digital parking
sensors for rear. (PSR4000)
b.2 digital parking sensors for front, 2 for rear. (PSR4000)
c.4 digital parking sensors for rear, 4 for front. PSR4000 and PSK4( /PSK4 Flush)
For Rear: 4 sensors installation
For Front 4 sensors installation:
For Rear 2 sensors in: stallation
For Front 2 sensors installation:
Place the speaker and control box inside a vehicle. Avoid from water
damages. The LED built-in speaker/speaker sound will indicate the
distance between the sensors and the object. Shorter pitch tone sound
indicates getting closer to objects.
- 8 -
3) Generally, it is the best to mount the sensors as high as possible in the bumper.
Use paint masking tape and mark the location as above diagram for the proper
spacing of the sensors.
4) Also be sure that the bumper surface and the sensors will fit at to the gr
o
90 ound.
Make sure the hole surface is clean and start cutting the bumper surface in
counter clockwise direction (A) first to prevent from paint to chip, then drill the
hole in clockwise direction . (B)
PSR4000/PSK4
sensors MUST be installed from outside of the bumper.
Please check the direction dot (WHITE) and make sure of the correct
orientation.
Important!
MUST CHECK BEHIND THE BUMPER FOR ANY METAL BRACKETS OR
INTERNAL BRACES BEFORE DRILLING
Check for the direction
- 9 -
Ce manuel convient aux modèles suivants
4
Table des matières
Autres manuels Rydeen Automobile électronique
