Rx Clear 801405 Manuel utilisateur

8809

MODEL # 801405

Rx Clear®

12" SAND FILTER SYSTEM

with 1/2 HP PUMP

INCLUDES BASE FOR FILTER AND PUMP

TOOLS

REQUIRED

•Phillips head screwdriver

•Flat head screwdriver

•O-ring lube

PARTS FOR SAND FILTER

FILTER

TANK

CLOSURE CLAMP STANDPIPE VALVE O-RING

4 WAY VALVE

NOTE

See breakdown on following page for model specific part lists.

DRAIN PLUG

HOSE CLAMPS (6) STRAIGHT FITTING (3) TEFLON TAPE

SHORT HOSE (1) LONG HOSE (2)

BASE

PRESSURE GAUGE

HOSE ADAPTERS (2)

Rx Clear® 12" SAND FILTER with 1/2 HP PUMP

PART #

MODEL # DESCRIPTION QTY

1 AC 85685 Filter Base 1

2 AC 83402 Drain Plug 1

3 AC 83380 Stand Pipe 1

4 AC 83399 Filter Tank 1

5 AC 83348 O-Ring 1

6 AC 83364 Flange Clamp 1

7 AC 83321 4 Way Valve 1

8 AC 84514 Bolt Kit 1

9 BS 40061BLK Straight Fitting 1

10 LOM 150 Clamp 1

11 AC 52221 1.25” x 24” Hose 1

12 BS10014 1.5”x3’Hose 1

13 AC 76473 Rear Mount Pressure Gauge 1

14 N/A N/A

STEP 1

•Remove the valve (1) from the box and place it to the side until instructed to attach it.

ASSEMBLY INSTRUCTIONS

FOR SAND FILTER

•Inside the tank you will find the standpipe (5) and

a plastic bag containing various parts, remove from

tank and set aside.

NOTE

Filter may be partially assembled; however, nothing has been

properly tightened. DO NOT operate filter system without

completing assembly instructions.

STEP 2

ATTACHING THE DRAIN ASSEMBLY

If drain assembly is all together, take it apart.

Take one rubber gasket and put over threaded

part of the drain assembly. Flat part of gasket

must be flush against sealing plate.

From inside the tank insert drain

assembly through hole in bottom of

tank, you will see the threaded part on

the outside of the tank.

Place other gasket on threaded part of the

drain assembly that is outside of tank flat

side to the tank.

Place locking nut on threaded part and

thread until snug. Hand tighten only. Be

sure to hold drain assembly from inside

while tightening locking nut.

Place drain cap over threaded port on outside of

tank. Hand tighten only.

STEP 3

•The filter and pump should be attached to the base prior to filling the filter with sand as it

will be difficult to maneuver after the tank is full.

A. CRADLE STYLE MOUNT

•Pumps with cradles located directly under the motor should be aligned

with the 4 holes that match up to the cradle. This type of mount will

require the use of four mounting bolts and nuts from the hardware

supplied with the base.

•Place nuts underneath the base, in

the properly aligned hole

•Bolt the housing of the pump through the base

and tighten.

•Cover the threads of each straight fitting with

teflon tape and thread one fitting into the front of

the motor and one fitting to the top of the motor.

•Attach the 1 1/4” hose with a clamp on each

fitting.

STEP 4

•Before filling tank with sand, place nub on bottom

of tank into notched out piece of the base, twist to

the right till snug.

NOTE

Sand should be filled no less than 1/2 way up the tank and no more

than 3/4. Over-filling will result in permanent damage to your

Filter System.

•Add filter grade sand (sold separately) to

filter tank around standpipe.

12” Tank ...... 50 Lbs.

14” Tank ...... 75 Lbs.

•Remove plastic protector and fill tank with water until the tank is filled right below

opening of standpipe.

NOTE

NEVER FILL SAND TANK MORE THAN 1/2 TO 3/4 OF THE

WAY.

•Place standpipe inside the filter, cover standpipe

with the round plastic standpipe protector to

prevent sand from entering standpipe.

STEP 4 — CONTINUED

•Locate o-ring (3) in bag with various parts.

•Lubricate with o-ring lube to ensure proper seal

on tank.(O-Ring lube not included)

•Push o-ring against the lip of the valve. It MUST sit

flat against the lip to protect from leaking at the valve.

•Clean off any sand or debris on top lip of filter and

position valve over the opening of the standpipe.

•Valve will slide ONTO standpipe when positioned

properly in tank (as shown). Push down firmly to make

sure valve slides on all the way.

NOTE

You CANNOT pull standpipe up to secure the valve.

Pulling up can damage the hub and cause sand to get

sent back with water flow to pool.

•Place valve so that pump port is directly

over the pump.

STEP 4 — CONTINUED

•Make sure that the screws of the clamp are lined up with the

seams of the tank. Tighten two screws on clamp a little at a time.

Alternating from side to side so that both sides are tightened

equally. Failure to follow these instructions will result in

a leak at the clamp.

•Cover threads of pressure gauge with Teflon tape.

Remove temporary plug from valve and thread

gauge into opening.

STEP 5

•The valve ports are labeled “RETURN”, “PUMP” and

“WASTE” with raised letters next to or on the the openings.

•Attach one long hose to the bottom of the thru-wall skimmer

and to the front of the pump with hose clamps on each fit-

ting.

•Attach second long hose to the fitting on the “RETURN”

and to the pools return fitting with hose clamps on each fit-

ting.

•“WASTE” port will accept a standard fitting and a backwash

hose

(sold separately) which will be used during maintenance.

•Check drain plug at bottom of filter to ensure that it is

•Once valve is in place, hold clamp (2) as shown

and position clamp around lip of filter and over edge

of valve. 2 long screws and nuts are provided to put

clamp together.

•The clamp should sit flat around the lip of the tank

and valve. If it is not sitting flat the clamp will leak.

HOSE CONNECTIONS FOR STANDARD ABOVEGROUND POOLS

HOSE CONNECTIONS FOR TEMPORARY ABOVEGROUND POOLS

AC 124EZ5G and FILTERS EQUIPPED WITH AC 22764 FITTINGS

1. Take the short hose. Place a clamp onto each end of the short hose. Leave loose.

Slide one end of the short hose over the exhaust port of you pump. This is the port

opening at the top of the pump not the one in front of the pump. Once in place tighten

that clamp. Take the other end of the short hose and slide it onto the port of the multi-

port valve labeled PUMP. This port is identified by the word “PUMP” embossed on the

side of the port on the vale itself. Tighten the clamp.

2. Take one of the long hoses. Place a clamp onto each end of the hose. Again leave

them loose. Slide one end of the hose over the intake port of the pump. This is the port

attheveryfrontofthepump.Tightentheclamp.Taketheotherendofthe6’hoseand

slide it over the port of the pools thru wall skimmer. Once in place tighten the clamp.

3. Take the remaining long hose. Place a clamp over each end of the hose, again

loosely. Slide one end of the hose over the port on the multiport valve labeled “POOL”.

The word “POOL “is embossed next to the correct port on the valve. Once in place

tightenclamp.Taketheotherendofthe6’hoseandslideitoverthepoolsreturnfitting

connection on the outside of the pool wall. Once in place tighten the clamp.

1. Take the short hose. Place a clamp onto each end of the short

hose. Leave loose. Slide one end of the short hose over the

exhaust port of you pump. This is the port opening at the top of

the pump not the one in front of the pump. Once in place tighten

that clamp. Take the other end of the short hose and slide it onto

the port of the multiport valve labeled PUMP. This port is identified

by the word “PUMP” embossed on the side of the port on the vale

itself. Tighten the clamp.

2. Take one of the long hoses. Place a clamp onto each end of the

hose. Again leave them loose. Slide one end of the hose over the

intake port of the pump. This is the port at the very front of the

pump.Tightentheclamp.Taketheotherendofthe6’hoseand

slide one of the AC 22764 fittings onto the end and tighten the

clamp. Attach the fitting (now connected to the hose) to the

suction/intake port of your temporary pool. Hand tighten fitting.

3. Take the remaining long hose. Place a clamp over each end of

the hose, again loosely. Slide one end of the hose over the port

on the multiport valve labeled “POOL”. The word “POOL”

is embossed next to the correct port on the valve. Once in place

tighten clamp. Take the other end of the long hose and slide the

other AC 22764 fitting into the end and tighten the clamp. Attach

the fitting to the pools return port on the outside of the pool wall.

Hand tighten fitting

AC 22764

Table des matières

Autres manuels Rx Clear Système de filtration d'eau

Rx Clear

Rx Clear HydroSalt Manuel utilisateur

Manuels Système de filtration d'eau populaires d'autres marques

Wisy

Wisy LineAir 100 Manuel utilisateur

Schaffner

Schaffner Ecosine FN3446 Series Manuel d'utilisation

Pentair

Pentair FLECK 4600 SXT Guide de l'utilisateur

H2O International

H2O International H20-500 Manuel utilisateur

Renkforce

Renkforce 2306241 Manuel utilisateur

Neo-Pure

Neo-Pure TL3-A502 Manuel utilisateur

FLTR

FLTR OBF Manuel utilisateur

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Manuel utilisateur

Applied Membranes

Applied Membranes W-G844EM Manuel utilisateur

BEGA

BEGA 116 Manuel utilisateur

WATA

WATA Standard Manuel utilisateur

Price

Price FFU series Manuel

Gaggenau

Gaggenau BRITA INTENZA 467873 Manuel utilisateur

Brita

Brita SAFF-100 Manuel utilisateur

HEISSNER

HEISSNER FPU24000-00 Manuel utilisateur

BGS technic

BGS technic 1518 Manuel utilisateur

Reverse Osmosis

Reverse Osmosis RF Series Manuel utilisateur

ubbink

ubbink Filtramax Series Manuel utilisateur