Ruijie Networks RG-AP220-E Manuel d'installation et d'exploitation
RG-AP220-E Series Access Point
Hardware Installation and Reference Guide V1.3
Copyright statement
Ruijie Networks©2000-2013
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup,
modification, transmission, translation or commercial use of this document or any portion of this document,
in any form or by any means, without the prior written consent of Ruijie Networks is prohibited.
, , , ,
,,
,, ,
, , are registered trademarks of Ruijie
Networks. Counterfeit is strictly prohibited.
Exemption statement
This document is provided “as is”. The contents of this document are subject to change without any notice.
Please obtain the latest information through the Ruijie Networks website. Ruijie Networks endeavors to
ensure content accuracy and will not shoulder any responsibility for losses and damages caused due to
content omissions, inaccuracies or errors.
Preface
Thank you for using our products. This manual will guide you through the installation of the access point.
Scope
It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it
is assumed that the users are already familiar with the related terms and concepts.
Obtaining Technical Assistance
Ruijie Networks website: http://www.ruijienetworks.com.cn
Online customer services: http://webchat.ruijie.com.cn
Customer service center: http://www.ruijie.com.cn/service.aspx
Customer services hotline: +86-4008-111-000
BBS:
http://support.ruijie.com.cn
Customer services email: [email protected]
Related Documents
Documents Description
Configuration Guide Describes network protocols and related mechanisms that supported by the
product, with configuration examples.
Command Reference Describes the related configuration commands, including command modes,
parameter descriptions, usage guides, and related examples.
Documentation Conventions
The symbols used in this document are described as below:
This symbol brings your attention to some helpful suggestions and references.
This symbol means that you must be extremely careful not to do some things that may damage the device or
cause data loss.
Chapter 1 Product Overview
The RG-AP220-E series wireless LAN access point (models: RG-AP220-E V1.X and RG-AP220-E V2.X) is designed by
Ruijie Networks for indoor high-density deployment or distributed deployment. It is ideal for large-sized campuses, branch
offices, hospitals, and Wi-Fi hotspots. The AP can serve as a Fit AP and operate in conjunction with a Ruijie WS series
wireless controller; or it can serve as a standalone Fat AP and provide wireless access for mobile clients.
RG-AP220-E V1.X
Model RG-AP220-E V1.X
Feature Indoor dual band dual radio access point
Interfaces
One Gigabit combo port (one 10/100/1000M auto-sensing RJ45 port and one SFP port)
One Console port (The AP220-E V1.10 went out of production and they were designed without
any fiber port; other AP220-E V1.X series products have fiber ports.)
Antennas
Connectors
Six external antennas
Six SMA connectors
Power Adapter Input: 90-264 V AC,50-60 Hz
Output: 48 V DC, 0.4 A max.
PoE IEEE 802.af PoE
Power Consumption 12.95 W
Operating
Frequency
802.11b/g/n: 2.4 GHz to 2.4835 GHz
802.11a/n: 5.725 GHz to 5.850 GHz
Transmit Power 100 mW (20 dBm), adjustable
Operating: 0 to 50℃(32 to 122 ℉)
Temperature Storage: -40 to 70℃(-40 to 158 ℉)
Operating:10% to 95% noncondensing
Humidity Storage: 5% to 95% noncondensing
Size (W x D x H) 24 cm x 22 cm x 4 cm
9.44 in. x 8.66 in. x 1.57 in.
Weight 1.6 kg (3.53 lbs)
RG-AP220-E V2.X
Model RG-AP220-E V2.X
Feature Indoor dual band dual radio access point
Interfaces One Gigabit combo port (one 10/100/1000M auto-sensing RJ45 port and one SFP port)
One Console port
Antennas
Connectors
Six external antennas
Six SMA connectors
Power Adapter Input: 90-264 V AC,50-60 Hz
Output: 48 V DC, 0.4 A max.
PoE IEEE 802.af PoE
Power Consumption 11.2W
Operating
Frequency
802.11b/g/n: 2.4 GHz to 2.4835 GHz
802.11a/n: 5.725 GHz to 5.850 GHz
Transmit Power 100 mW (20 dBm), adjustable
Operating: 0 to 50℃(32 to 122 ℉)
Temperature Storage: -40 to 70℃(-40 to 158 ℉)
Operating:10% to 95% noncondensing
Humidity Storage: 5% to 95% noncondensing
Size (W x D x H) 24 cm x 22 cm x 4 cm
9.44 in. x 8.66 in. x 1.57 in.
Weight 1.6 kg (3.53 lbs)
Chapter 2 Precautions
To avoid damages to the AP, observe the following safety precautions:
Install the device in a well-ventilated location.
Do not subject the device to high temperatures.
Keep the device away from high voltage cables.
Install the device indoors.
Do not expose the device in a thunderstorm or strong electric field.
Keep the device clean and dust-free.
Disconnect the device before cleaning it.
Do not use a damp cloth or liquid for cleaning.
Do not open the enclosure when the AP is working.
Make sure the output voltage of the adapter matches the specifications.
Fasten the device tightly.
Make sure all antennas are connected before powering up the device.
Before you power up the AP, make sure all antennas are connected. Otherwise, it may cause damages to
the device.
Chapter 3 Installing the Access Point
Disconnect the power supply while installing or moving the AP.
Tighten all screws.
Keep the LED light in sight.
Wall Anchors and Screws
Reference sizes for wall anchors and screws:
Wall anchors: M7x￠4.5x28 (mm)
Screws: 4*20PABC (mm)
Figure 3-1 Screws
Figure 3-2 Wall Anchors
Installing the AP
Follow the steps below:
1) Drill four 5 mm holes on the wall at the four corners of a rectangle (120 mm x 275 mm).
2) Insert the anchors into the holes. The rim of the anchor should be flush with the wall.
Figure 3-3 Studs and Screw on the Bracket
3) Drive screws through the mounting bracket into the anchors and mount the AP on the wall or ceiling.
4) Attach the three holes on the rear of the AP onto the three studs on the bracket, and pull the AP 8 mm away from the
screw direction. See Figure 3-3..
5) Tighten the screw on the bracket until it reaches the hole on the side of the AP.
The depth of the holes must fit the size of the wall anchors and screws used. Make sure that the wall anchors
can be inserted into the holes, leaving the rim of the anchor outside the wall. As you drive the screws in, the
anchors will expand to grip the wall tightly.
When installing the AP on a vertical surface, orient the mounting bracket with the screw side facing down.
Installing the Antennas
Connect the supplied omni-directional antennas to the SMA connectors on the AP. Make sure the three antennas at each
side are parallel to one another. Ruijie recommends you place the AP vertically.
Figure 3-4 Installing the Antennas
Power Sources
The AP can be powered either with a 48V DC power adapter or through Power over Ethernet (PoE).
PoE
When using PoE, verify that the power supply equipment is IEEE 802.11af PoE compliant, and the Ethernet cable is
connected to the Ethernet port on the AP. Figure 3-5 shows the location of the Ethernet port on the AP.
Figure 3-5 Ethernet Port
Note 1.Reset button
2.Console port
3. Fiber port LED (no LED, if no fiber port.)
4. 1000Base-X SFP port
5. Copper port LED
6.10/100/1000Base-T auto-sensing Ethernet port
7. Nameplate
8. Power port
Power Adapter
When using a power adapter, verify that it meets the recommended specifications, and the adapter is plugged in the
power port.
LED Indicators
After the AP is powered on, observe the LED on the cover and front panels to verify its operation.
Figure 3-6 LED Indicators
Note 1.Radio1 LED
2.Status LED
3.Radio2 LED
LED State Meaning
Off The AP is NOT receiving power. Or the power supply is faulty.
Blinking green Initialization in progress.
Continuous blinking indicates errors
Solid green The AP is operational.
Status
Solid red The AP is faulty.
Off The wireless card is turned off.
Solid green The wireless card is turned on and operates in the 2.4 GHz band.
Radio1/2*
Blinking green The wireless card operates in the 2.4 GHz band and is receiving or
transmitting traffic.
Off The AP is not powered on or the power supply does not function
properly.
Power*
Solid green The AP receives power normally.
Autres manuels pour RG-AP220-E
1
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Ruijie Networks Point d'accès sans fil
Ruijie Networks
Ruijie Networks RG-SAP815-SP Manuel d'installation et d'exploitation
Ruijie Networks
Ruijie Networks RG-AP220-I Series Manuel d'installation et d'exploitation
Ruijie Networks
Ruijie Networks i-Share+ Series Dimensions
Ruijie Networks
Ruijie Networks Reyee RG-RAP2266 Manuel d'installation et d'exploitation
Ruijie Networks
Ruijie Networks RG-AM5528 Series Manuel d'installation et d'exploitation
Ruijie Networks
Ruijie Networks RG-AP820-I Manuel d'installation et d'exploitation
Ruijie Networks
Ruijie Networks RG-AP130-W Manuel utilisateur
Ruijie Networks
Ruijie Networks RG-MAP552(SR) series Manuel d'installation et d'exploitation
Ruijie Networks
Ruijie Networks RG-AP630 CD Manuel utilisateur
Ruijie Networks
Ruijie Networks RG-AP820-L Manuel d'installation et d'exploitation
Ruijie Networks
Ruijie Networks RG-AP220-E Manuel d'installation et d'exploitation
Ruijie Networks
Ruijie Networks Reyee RG-RAP1261 Manuel d'installation et d'exploitation
Ruijie Networks
Ruijie Networks RG-AP320-I Series Manuel d'installation et d'exploitation
Ruijie Networks
Ruijie Networks RG-AP520(DA) Series Manuel d'installation et d'exploitation
Ruijie Networks
Ruijie Networks RG-AP810-L Manuel d'installation et d'exploitation
Ruijie Networks
Ruijie Networks RG-AP3220 Series Manuel d'installation et d'exploitation
Manuels Point d'accès sans fil populaires d'autres marques
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur
Ubiquiti
Ubiquiti NanoStation NSM2 Manuel utilisateur
Cisco
Cisco Aironet 1550 Series Manuel utilisateur
Aruba
Aruba IAP-335 Manuel utilisateur
Advantek Networks
Advantek Networks AWN-AP-54MR Manuel utilisateur
IP-COM
IP-COM AP355 Manuel utilisateur
