Ruckus Wireless SmartZone 100 Manuel utilisateur

Ruckus SmartZone 100

Quick Setup Guide

Supporting SmartZone 5.1

This Quick Setup Guide provides basic instructions for

setting up the Ruckus SmartZone 100 (SZ100) on the

network. For information on advanced conguration and

management options, see the SmartZone 100 Getting

Started Guide and SmartZone 100 Administrator Guide,

which are available for download from the Ruckus

Support website:

https://support.ruckuswireless.com/documents

This Guide in Other Languages

请从以下网站获得该指南的简体中文版 https://

support.ruckuswireless.com.

Vous trouverez la version française de ce guide à

l'adresse suivante https://support.ruckuswireless.com.

このガイドの日本語版は https://

support.ruckuswireless.com でご覧ください。

이 가이드의 한국어 버전은 웹 사이트 (https://

support.ruckuswireless.com) 에서 확인하시기 바랍니다.

Veja a versão em português (Brasil) deste guia em

https://support.ruckuswireless.com.

Puede ver la versión en español (América Latina) de esta

guía en https://support.ruckuswireless.com.

Licensing Information

The SZ100 comes pre-shipped with 1000 temporary AP

Capacity Licenses, which are valid for a period of 90 days

from when the SZ100 is congured via the initial setup

conguration. For operation beyond 90 days, you MUST

buy permanent AP Capacity licenses. The purchased

Licenses MUST be activated for them to become valid.

The management of the AP Capacity Licenses and the

ability to activate the permanent License will be through

the Ruckus Support Portal (https://

support.ruckuswireless.com). An email will be sent to the

User that is identied on the Purchase Order and full

instructions as to how to activate the Licenses is included

in the email. As a guide, full instructions can be found at

https://support.ruckuswireless.com/activate.

Using the LiMAN (license management) portal on the

Ruckus Support website, you can assign licenses to or

from a SZ100 or move them to another SZ100 (see a

summary of LiMAN features in Table 1). To physically

manage the distribution of licenses from the Support

website to the actual SZ100, do one of the following:

•Connect the SZ100 directly to the Internet.

•Deploy a Ruckus Local License Server (LLS) within your

network. The LLS must be able to communicate with

your SZ100 and it must be connected to the Internet.

–LLS should rst synchronize with the license server in

the cloud to get the required license (as per the

SZ100 serial number)

–Remove licenses from one SZ100 to add to another

NOTE: NOTE: In the event that the SZ100 is not

connected to the Internet and you have not deployed

an LLS, you can download the actual licenses from the

Support Portal and manually upload to the specic

SZ100.

For step-by-step instructions on how to activate the

SZ100’s licenses, see Step 5: Activate the SZ100’s Licenses

on page 3.

TABLE 1 LiMAN features and how to activate them on the

SZ100

LiMAN Features SZ100 Online

(Connected to

the Internet)

SZ100 Oine

(Disconnected

from the

Internet)

•Register SZ100

controllers,

licenses,

support

entitlement

•Add capacity

licenses to

SZ100

controllers

•Remove

licenses from

one SZ100 and

add to another

No action

required. The

SZ100 syncs with

LiMAN

automatically

within 24 hours

and applies the

appropriate

licenses.

Three steps

required:

1. Download the

license le

from LiMAN.

2. Log on to the

SZ100, and

then upload

the license

le from

LiMAN.

3. Download the

license

response le

from the

TABLE 1 LiMAN features and how to activate them on the

SZ100 (continued)

LiMAN Features SZ100 Online

(Connected to

the Internet)

SZ100 Oine

(Disconnected

from the

Internet)

SZ100, and

then upload it

to LiMAN.

Before You Begin

Before deploying Ruckus Networks products, please

check for the latest software and the release

documentation.

•Release Notes and other user documentation are

available at http://support.ruckuswireless.com/

documents.

•Software upgrades are available at http://

support.ruckuswireless.com/software.

•Open source information is available at http://

opensource.ruckuswireless.com.

•Software license and limited warranty information are

available at http://support.ruckuswireless.com/

warranty.

Package Contents

•One SmartZone 100 appliance with one AC/DC power

supply unit and power cord

•One console cable

•One rack mount kit

•Service Level Agreement/Limited Warranty Statement

sheet

•Regulatory Statement sheet

•This Quick Setup Guide

What You Will Need

•An administrative computer (admin PC) with a

connection to the local area network

•A web browser, such as Internet Explorer, Mozilla

Firefox, Google Chrome or Apple Safari

•The IP address, netmask, gateway and DNS server

addresses assigned to the SZ100 —if it has a static

network address (recommended)

Published November 2018, Part Number 800-71962-001 Rev A

Step 1: Connect the SZ100 to the Network

1. Connect the SZ100 to a convenient power source, and

then press the power switch on the rear panel. The

Alarm LED shows a ashing red light as the SZ100

starts up. When the SZ100 has started up

successfully, the Alarm LED turns to a solid green

light.

2. Obtain an Ethernet cable. Connect one end of the

Ethernet cable to one of the LAN ports (port 1 or 2

recommended) on the SZ100, and then connect the

other end to your network’s switch or router. DHCP

server should be available in the connected LAN

environment for SZ100 to get the IP address.

NOTE: The SZ100 is a Universal Plug and Play

(UPnP) device. Once you connect it to the network,

it will automatically congure itself, obtain an IP

address, and make its presence known to other

devices on the network.

3. Go to the admin PC and verify that the SZ100 is now

discoverable on the network. On Windows 7 and

Windows 8, go to Control Panel > Network and

Internet > View network computers and devices,

and then locate the Network Infrastructure section.

The SZ100 should appear there. In such scenarios,

SZ100 and a system (laptop or a PC) should have

cross-over connection and the system should have an

IP address in the same subnet as SZ100. Congure

SZ100 MGMT and CONTROL interface and add it to

the new LAN connection. Use the new IP address to

access SZ100.

NOTE: If you prefer not to use UPnP, you can type

the IP address of the SZ100 into a web browser

instead. In case there is no DHCP server on the

network, the default IP address and URL of the

SZ100 is http://192.168.2.2:8080 with a network

mask of 255.255.255.0. Otherwise, an IP address is

assigned automatically from your existing DHCP

service.

FIGURE 1 The SZ100 appears in the Network

Infrastructure section

4. Double-click the SZ100 that appears in the Network

Infrastructure section to start the SZ100’s Setup

Wizard.

A web browser loads and the SZ100’s Setup Wizard

appears, displaying the Port Conguration screen.

FIGURE 2 The Port Conguration screen of the Setup

Wizard

Step 2: Complete the Setup Wizard

1. When the Setup Wizard appears, complete the

following screens:

• Port Conguration: If you want to combine the

management, AP control, and AP tunnel trac on a

single interface (recommended for simple setup),

click One Port Group. If you want to separate the

management and AP control trac from the AP

tunnel trac, click Two Port Group.

NOTE: If you clicked Two Port Group, verify that

the admin PC is connected to either port 1 or

port 2 of the SZ100.

• IP Setting: Congure the IP address settings of the

SZ100 interface or interfaces either by assigning

addresses automatically (if a DHCP server exists on

the network) or manually:

–If you clicked One Port Group on the previous

screen, congure the SZ100’s IP address settings

on the IP Setting screen.

–If you clicked Two Port Group, congure the IP

address of the management and AP control

interface on the Port 1 screen, and then

congure the IP address of the AP tunnel data

interface on the Port 2 screen.

• Cluster Information: Select whether you want to

create a new cluster with this SZ100 or to join an

existing cluster on the network. If you want this

SZ100 to join an existing cluster, you must type the

cluster IP address and admin password in the

boxes provided.

2. When the Conrmation screen appears, verify that

all the settings displayed on the screen are correct.

If you need to make a correction, click Back until the

appropriate setup screen appears, then make the

changes.

3. If they are all correct, click Finish to apply the settings

and activate the SZ100 on the network.

A progress bar appears and displays the progress of

applying the settings, starting the SZ100 services, and

activating the SZ100 on the network.

When the process is complete, the progress bar

shows the message “100% Done.” The page also

shows the IP address through which you can access

the SmartZone web interface to manage the

appliance.

NOTE: Take note of this IP address. You will need

this later to log on to the SZ100’s web interface.

FIGURE 3 Take note of the IP address of the web

interface

Published November 2018, Part Number 800-71962-001 Rev A

Step 3: Connect the SZ100 to the Network

1. Connect Port 1 to the router or switch.

2. Connect Port 2 to another router or switch to which

other SmartZone appliances (if present) are

connected.

NOTE: Depending on your network setup, you may

also connect Port 2 to the same router or switch to

which Port 1 is connected.

Step 4: Connect the APs to the Network

1. Distribute the APs around your worksite.

2. Record each AP’s Ethernet MAC address (printed on

the bottom of every AP), and note each device’s exact

worksite location.

3. Connect the APs to a local power source.

4. Using an Ethernet cable, connect the APs to the

switch or router on the same network as the SZ100.

NOTE: Some APs are PoE-capable. If connected to a

Power over Ethernet switch, the APs can draw

power through the Ethernet cables.

When the APs are powered on, they will automatically

discover the SZ100 on the network.

NOTE: If an AP is already running a SZ image then

auto-discovery on same LAN/IP subnet will not

work. It only works if the AP is running a SZ/

universal LWAPP based image.

FIGURE 4 Connecting the admin PC, SZ100, and APs to

the network

Step 5: Activate the SZ100’s Licenses

After you set up the SZ100 and verify that wireless clients

are able to associate with managed APs successfully, you

need to activate and assign the AP and Tunnel Licenses

using the LiMAN (license management) portal on the

Ruckus Networks Support site.

Before You Begin

You must have a Ruckus Support portal account

(including user name and password). You can use this

account to access general Support site content including

software upgrades, knowledge base articles and technical

documents.

If you do not have a Support portal account, you will be

required to register one before continuing with your

product and license activation.

Every capacity and support license that you have

purchased will have its own unique activation code and

each must be activated for the license to become valid.

You will receive the activation code in a separate Support

Purchase Acknowledgment (SPA) email for each license/

support license.

Depending on the product, you may receive up to three

(3) dierent SPA emails for all of your licenses. The rst

three characters of the activation code indicate the

license type to which the code is applicable.

• LIC: AP Capacity License

• LIC: AP Tunnel License

• SUP: Support License

Activating a SZ100’s License/Support License

1. Open the SPA email that you received from Ruckus

Networks.

FIGURE 5 The SPA email from Ruckus

2. Log on to https://support.ruckuswireless.com.

FIGURE 6 Ruckus Support portal logon page

3. Have the serial number of your SZ100 device ready.

4. Click the link in the SPA email.

5. Follow the onscreen instructions to activate the

licenses purchased. When required, you will be

prompted for your SZ100 serial number.

6. It is important that you repeat steps #1 to #5 above

for all licenses that you have purchased as this will

simplify the “+License” workow in Step 7 below.

7. After you nish activating all of your licenses, you

need to assign them to your LiMAN account. Click the

LiMAN button, which appears after a license has

been successfully activated (see Figure 7).

•If your device is listed, click its serial number and

proceed to Step 8.

•If your device is NOT listed, click the Register

Smart Device button (see Figure 8), enter your

device's serial number, and then click the Register

Smart Device button (see Figure 9).

FIGURE 7 Click the LiMAN button

Published November 2018, Part Number 800-71962-001 Rev A

FIGURE 8 Click the serial number of your device or click

FIGURE 9 Enter your device’s serial number and click

8. Click the + License button (see Figure 10), enter the

number of licenses to add in Qty to Add, and then

click the Add License button (see Figure 11). Repeat

for all licenses.

FIGURE 10 Click + License

FIGURE 11 Enter the number of licenses to add in Qty to

Add and click Add License

You have completed activating a SZ100’s licenses.

Step 6: Sync the SZ100 with LiMAN

After you have activated the SZ100’s licenses on the

Ruckus Networks Support Portal, the SZ100 must be

synced with the Smart License server. This will enable the

User’s ability to assign licenses to and back from a SZ100

or assign them to another SZ100.

To physically manage the distribution of licenses from the

Support Portal to the actual SZ100, do one of the

following:

•Connect the SZ100 directly to the Internet. On the

SmartZone web interface, go to the Administration >

License Servers tab, and then click the Sync Now

button to sync the SZ100 with the SmartLicense server.

FIGURE 12 Sync the SZ100 with the SmartLicense server

•Deploy a Ruckus Local License Server (LLS) within your

network. The LLS must be able to communicate with

your SZ100 and it must be connected to the Internet.

Contact Ruckus Wireless Support for information on

how to setup an LLS.

View the synced license details by navigating the

controller's web interface to Administration > License

page > Installed Licenses.

FIGURE 13 Installed Licenses

•In the event that the SZ100 is disconnected from the

Internet and you have not deployed an LLS, you can

download the actual licenses from the Support Portal

and manually upload them to the specic SZ100. See

Syncing Licenses on an Oine SZ100 on page 5.

You have completed activating the capacity or support

license for the SZ100 device.

Published November 2018, Part Number 800-71962-001 Rev A

Syncing Licenses on an Oine SZ100

1. On the Add License page of LiMAN, click the SZ100’s

serial number. The View Device page appears (see

Figure 14).

FIGURE 14 The View Device page

2. Click Download License File. The license le is saved

to the client.

3. On the SZ100 web interface, go to Administration >

License . In the Upload License section (see Figure

12 on page 4), click the Browse button, and then

select the license le from your client to upload it to

the SZ100

4. On the SZ100 web interface, go to Administration >

License. In the Download License section, click the

Download button to download the license le from

the SZ100 to your client.

5. Go back to the LiMAN portal on the Ruckus Networks

Support website, and then do the following:

a) Go to the View Device page (see Figure 14).

b) Click Upload License File.

c) Click the Choose File button (see Figure 15), and

then select the license le from your client.

d) Click Send to complete the oine License

synchronization.

You have completed activating licenses on an oine

SZ100.

FIGURE 15 Click the Choose File button

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur