Ruby VC-410 Manuel utilisateur

VC-410 & VC410POE Ethernet Extender Manual

C-

-4

C-

-4

VC-410 & VC410POE Ethernet Extender Manual

Trademarks

RubyTech is a trademark of Rubytech Deutschland GmbH

Other brand and product names are registered trademarks or trademarks of their respective

holders.

Legal Disclaimer

The information given in this document shall in no event be regarded as a guarantee of

conditions or characteristics. With respect to any examples or hints given herein, any typical

values stated herein and/or any information regarding the application of the device, Rubytech

Deutschland GmbH hereby disclaims any and all warranties and liabilities of any kind, including

without limitation warranties of non-infringement of intellectual property rights of any third party.

Statement of Conditions

In the interest of improving internal design, operational function, and/or reliability, RubyTech

reserves the right to make changes to the products described in this document without notice.

RubyTech does not assume any liability that may occur due to the use or application of the

product(s) or circuit layout(s) described herein.

Maximum signal rate derived form IEEE Standard specifications. Actual data throughput will vary.

Network conditions and environmental factors, including volume of network traffic, building

materials and construction, and network overhead lower actual data throughput rate. RubyTech

does not warrant that the hardware will work properly in all environments and applications, and

makes no warranty and representation, either implied or expressed, with respect to the quality,

performance, merchantability, or fitness for a particular purpose.

Make sure you follow in line with the environmental conditions to use this product.

VC-410 & VC410POE Ethernet Extender Manual

Foreword: VDSL2 solution

Attention:

Be sure to readthis manual carefullybefore using this product. EspeciallyLegal Disclaimer,

Statement of Conditions and Safty Warnings.

VC-410 & VC-410 & VC410POE is a Long Reach Ethernet Extender with PoE equipped with two

10/100Mbps Ethernet ports with power injector. It delivers data and electrical power to access

points using standard Category 5 Ethernet cable that provide an economical solution for

commercial-grade applications.

Operators in various enterprises will now be able to deploy PoE devices in any service

location, install network security cameras, wireless access point security / VOIP, or access

control systems in any place where you have basic wire connectivity.

The VC-410 & VC410POE also supports both central office (CO) and customer-premises

equipment (CPE) modes selectable through DIP Switch.

Compliant with ITU-T G.993.2 VDSL2 standard, the VC-410 & VC410POE supports a maximum

bandwidth of up to 100Mbps symmetric in VDSL2 solution. Since VDSL2 has the characteristic of

higher bandwidth over shorter distances, the ideal architecture for Telcoms is to use fiber optic

lines as the backbone and a VDSL2 line as the last mile into the home or office. With outstanding

throughput, the VC-410 & VC410POE can complement a fiber network to offer the best solution

for delivering Triple play(Video/Voice/Data) or home entertainment services.

Caution:

The VC-410 & VC410POE is for indoor applications only. This product does not have

waterproof protection, please do not use in outdoor applications.

VC-410 & VC410POE Ethernet Extender Manual

Safety Warnings

For your safety, be sure to read and follow all warning notices

and instructions before using the device.

DO NOT open the device or unit. Opening or removing covers can expose you to

dangerous high voltage points or other risks. ONLY qualified service personnel can service

the device. Please contact your vendor for further information.

Use ONLY the dedicated power supply for your device. Connect the power to the right

supply voltage (110V AC used for

NorthAmerica and 230VAC used for Europe).

support 48 VDC power input.

Place connecting cables carefully so that no one will step on them or stumble over them. DO

NOT allow anything to rest on the power cord and do NOT locate the product where anyone

can work on the power cord.

DO NOT install nor use your device during a thunderstorm. There may be a remote risk of

electric shock from lightning.

DO NOT expose your device to dampness, dust or corrosive liquids.

DO NOT use this product near water, for example, in a wet basement or near a swimming

pool.

Connect ONLY suitable accessories to the device.

Make sure to connect the cables to the correct ports.

DO NOT obstruct the device ventilation slots, as insufficient air flow may harm your device.

DO NOT place items on the device.

DO NOT use the device for outdoor applications, and make sure all the connections

are indoors or have waterproof protection place.

Be careful when unplugging the power, because may produce sparks.

Keep the device and all its parts and accessories out of children’s reach.

Clean the device using a soft and dry cloth rather than liquid or atomizers. Power off the

equipment before cleaning it.

This product is recyclable. Dispose of it properly.

VC-410 & VC410POE Ethernet Extender Manual

TABLE OF CONTENTS

COPYRIGHT..................................................................................................................

.…. 2

FOREWORD:VDSL2

SOLUTION

......................................................................................

SAFETYWARNINGS

................................................................................................

…….. 4

CHAPTER 1. UNPACKING

INFORMATION

......................................................................

1.1 Check List ...................................................................................................…………... 6

CHAPTER 2. INSTALLING THE

BRIDGE

........................................................................

2.1 Hardware Installation.............................................................................................…. 7

2.2 Pre-installation Requirements.............................................................…………………... 7

2.3 General Rules...................................................................................…………………….. 8

2.4 Connecting the Bridge......................................................................…………………….. 8

2.5 Connecting the RJ-11 / RJ-45 Ports...............................................................………... 9

2.6 VDSL2 bridge Application ..............................................................................…….. 11

VC-410 & VC410POE Ethernet Extender Manual

CHAPTER 3. HARDWARE

DESCRIPTION ................................................................... .

3.1 Front Panel.............................................................................................................… 14

3.2 Front Indicators.......................................................................……………………………... 15

3.3 Rear Panel................................................................................................................ 17

APPENDIX

A: CABLE

REQUIREMENTS.........................................................................

APPENDIXB: PRODUCT

SPECIFICATION .....................................................................

APPENDIXC:

TROUBLESHOOTING ...............................................................................

APPENDIXD: COMPLIANCE

INFORMATION .................................................................

WARRANTY

.......................................................................................................................

VC-410 & VC410POE Ethernet Extender Manual

CHAPTER 1.UNPACKING INFORMATION

1.1 Check List

Carefully unpack the package and check its contents against the checklist.

Package Contents

1x VC-410 & VC410POE 1x CD Manual Accessory: 1 x Ehternet Cable, 4 x Rubber Feet,

1 x DC48V /1.875A Desktop Adapter,

1x AC to DC Power cord

Notes:

1. Please inform your dealer immediately for any missing or damaged parts. If possible, retain the

carton including the original packing material.

2. Use ONLY the dedicated power supply for your device. Do not use sub-standard power supply.

Before connecting the power supply to the device, be sure to check compliance with

specifications. The VC-410 & VC410POE support DC48V /1.875A power input.

3. Power supply included in package is commercial-grade. Do not use in industrial-grade

applications.

4. If you would like to use the telephone, please purchase a suitable external splitter and install to

the line port.

VC-410 & VC410POE Ethernet Extender Manual

Chapter 2. Installing the Bridge

2.1 Hardware Installation

This chapter describes how to install the bridge and establishes network connections

and may install the bridge on any level surface (e.g. a table or shelf or rail). However,

please take note of the following minimum site requirements before one begin.

2.2 Pre-installationRequirements

Before you start the actual hardware installation, make sure you can provide the right

operating environment, including power requirements, sufficient physical space, and

proximity to other network devices that are to be connected.

If you experience any error or problem, please be sure, RubyTech will care for you and the

problem. Please contact your local dealer for support. If you are told to send the device

for RMA and repair, ALWAYS ship the whole device with power supplies.

Verify the following installation requirements:

Power requirements: DC 48V power.

The bridge should be located in a cool dry place, with at least 10cm/4in of space at the

front and back for ventilation.

Place the bridge away from direct sunlight, heat sources, or areas with a high amount of

electromagnetic interference.

Check if the network cables and connectors needed for installation are available.

Do Not install phone lines strapped together withAC power lines, or telephone office line

with voice signal.

Avoid installing this device with radio amplifying station nearby or transformer station

nearby.

VC-410 & VC410POE Ethernet Extender Manual

2.3 General Rules

Before making any connections to the bridge, please note the following rules:

•

Ethernet Port (RJ-45)

All network connections to the bridge Ethernet port must be made using

Category 5 UTP or above for 100Mbps, Category 3, 4 UTP for 10Mbps.

No more than 100 meters of cabling may be use between the

MUX or HUB and an end node.

•

VDSL2 Port (RJ-11)

All network connections to the RJ-11port must use 24~26

gauge with twisted pair phone wiring. Recommended is at

least AWG26, better AWG24. Avoid to use any telephony

ribbon cables. Avoid to use any low diameter cables.

2.4 Connecting the Bridge

The bridge has two Ethernet ports which support connection to Ethernet operation and PoE

function. The devices attached to these ports must support auto-negotiation or 10Base-T or

100Base-TX unless they will always operate at half duplex. VC-410 & VC410POE fast Ethernet

port is used to connect to external power splitter(PoE) or build in power splitter of networking

devices such as IP CAM, VOIP, wireless AP, sensor scanner or other power splitter(PD side)

more than 30W.

Notes:

1. The RJ11 Line port is used to connect to telephone that is connected to VDSL2 CO and CPE

bridge (Point-to-point solution).

2. Slave device(CPE) must connect Master device(CO) through the telephone wire. Slave

cannot connect to Slave, and Master cannot connect to Master. Please confirm the DIP switch

status before the link is established.

VC-410 & VC410POE Ethernet Extender Manual

2.5 Connecting the RJ-11 / RJ-45 Ports

The line port has 2 connectors: RJ-45 and terminal block. It is used to connect from VC-410 &

VC410POE(CO) using single pair phone cable to VC-410 & VC410POE(CPE) side (point to point

solution). Take note that VC-410 & VC410POE line port cannot be used at the same time. Either

RJ-11 port is connected or terminal block is connected using straight connection (Figure 2.4) or

cross-over connection (Figure 2.5)

When inserting a RJ-11 plug, make sure the tab on the plug clicks into position to ensure that it is

properly seated.

Do not plug a RJ-11 phone jack connector into the Ethernet port (RJ-45 port). This may

damage the bridge. Instead, use only twisted-pair cables with RJ-45 connectors that conform to

Ethernet standard.

Notes:

1. Be sure each twisted-pair cable (RJ-45 ethernet cable) does not exceed 100 meters (333 feet).

2. We advise using Category 5~7 UTP/STP cables for Cable bridge or Bridge connections to

avoid any confusion or inconvenience in the future when you attached to high bandwidth

devices.

3. RJ-11(VDSL2 Line port) use 24 ~ 26 gauge with twisted pair phone wiring, we do not

recommend 28 gauge or above.

4. Be sure phone wire has been installed before VC-410 & VC410POE powered on.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Ruby Extenseur

Ruby

Ruby VC-350PoE Manuel utilisateur

Manuels Extenseur populaires d'autres marques

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

SC&T

SC&T HE03-4K Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

MuxLab

MuxLab 500771 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur