Rousseau 2950 Manuel utilisateur
Heavy Duty Miter Saw Stand
Model 2950
OWNER’S MANUAL
IMPORTANT
Read and understand all safety guidelines and
instructions carefully before operating.
Quality Power Tool Accessories
2
GENERAL INFORMATION
You have purchased a Rousseau Company MITER SAW STAND 2950. De-
signed for job site use, it excels at handling long heavy material. This unit sets
up and folds quickly, and is easily loaded or unloaded by one person into a truck.
WARRANTY
This product has a lifetime warranty to the original purchaser. The warranty
applies to defects in materials and workmanship only. We will repair or replace
the product or part(s) at our discretion. This warranty does not apply to product
failure or defects due to direct or indirect misuse, abuse, negligence, accidents,
alterations, repairs or lack of maintenance. The item must be shipped prepaid to
our Clarkston, WA location. If items must be returned for warranty service, call
to receive a Return Goods Authorization (RGA) number and further instruction.
SAFETY GUIDELINES
THIS SECTION CONTAINS IMPORTANT SAFETY INFORMATION
CONCERNING A HAZARD THAT MAY CAUSE SERIOUS INJURY
OR DEATH, and/or damage to stand or equipment if used improperly.
Please read the following instructions very carefully.
Always follow the safety recommendations and guidelines
provided by the manufacturer of your tools. When in doubt
refer to your owner’s manual.
Always set stand on level ground or oor surface, making sure
all legs are in contact with the ground or oor. Extend legs
until locked. Failure to do so could result in saw movement
or the collapse of the table causing injury to the operator or
to the equipment.
Always keep hands clear of hinge and pivot points. Failure to
do so could result in serious injury or loss of ngers.
Be sure saw is bolted down securely. Failure to do so could
result in serous injury to self, saw and/or stand.
Adjust rollers or other material support surface to level with
bed of miter saw. Failure to do so could result in kickbacks,
causing serous injury to self, saw and/or stand.
When cutting small pieces use a hold down stick or clamp
work piece securely. Failure to do so could result in kick-
backs, serous injury to self, saw and/or stand.
3
When using any stop system, always hold work piece
securely on stop side, tight to table with hand a safe
distance from blade. Failure to do so could result in kickbacks,
causing serious injury to self, saw and/or stand.
On all cutting operations make sure the blade has come to
a complete stop before attempting to remove work piece.
Failure to do so could result in kickbacks, causing serious
injury to self, saw and/or stand.
SET UP AND ADJUSTMENTS
1. Lay miter saw stand upside down on level surface.
2. Place one wheel on axle with air stem pointing out. Install metal cap on the
same end of axle using the axle cap installation tool. Place one 5/8” spacer onto
the opposite end axle and slide until tight against wheel. Insert axle through the
holes in the bottom of each leg. Place remaining 5/8” spacer on axle followed
by the wheel with air stem pointing away from stand. Install metal cap using
installation tool.
3. Set stand on level ground with all legs touching equally.
4. Set miter saw on stand, center left to right, and toward the back to maximize
use of stock support rollers. Make sure the miter saw mounting holes will miss
tubing under top. IF NECESSARY SHIFT MITER SAW UNTIL MOUNTING
HOLES MISS TUBING. If you are using a support wing and stop system be
sure there will be no interference with the optional accessories before drilling
mounting holes. After adjusting saw to clear tubing, mark each hole on top,
drill and fasten saw to stand according to your saw owners manual. Mounting
hardware included with stand.
5. Loosen adjustment knobs on 1” tubing beneath top. Pull extension arm out
until 3” remain inside and tighten. Insert base of roller through extension arm
coupler and into “T” base. Raise roller until level with the miter saw bed and
tighten coupler with “T” base knobs. Repeat on opposite side.
OPTIONAL ACCESSORIES FOR 2950
6112 SUPPORT WING: Provides 61”x12” of stock support. Attaches to unit
with a quick release mounting bracket and accurately returns to previous
setting. Designed to quickly mount stop system. Can be attached to left or
right side.
6000 STOP SYSTEM: Available for left or right side, improves production and
accuracy of cutting to length one or several pieces. Eliminates the process
of measuring and marking each piece. Measures out to 10’ -6” from blade.
Requires use of 6112 support bracket.
4
2950 REV. 10-03
WARNING! KEEP FINGERS CLEAR OF HINGE PINCH POINTS WHEN FOLDING LEGS.
Reverse procedure to
erect Miter saw stand.
Make sure hinge sup-
ports are straight and
that spring buttons have
popped out when each
leg is extended.
1392 Port Drive, Clarkston, WA 99403
800-635-3416 • 509-758-3954 • Fax 509-758-4991
email:[email protected] • www.rousseauco.com
STEP 1 To relocate stand. STEP 2) To Fold: Remove “T” bases and
position arms & rollers as shown.
STEP 3 Depress hinge
support buttons, pull
hinge support and stand
toward yourself.
STEP 4 Firmly grasp roll-
er, pulling unit toward
yourself.
STEP 5 Set stand on
the ground.
STEP 6 Lift leg up until it
catches.
STEP 7 Depress buttons
and pull up on hinge
supports.
STEP 8 Lift unit with
roller ‘T’.
Loosen
knob and
raise “T”
base
Lift
and
Go
14”
+
-
6” In
+
-
Foot
against
leg
STEP 9 Push axle until leg
catch engages
STEP 10 Bottom roller
‘T’s stored between legs
and underside of stand.
Up
Tighten
knob
rmly
Table des matières
Autres manuels Rousseau Scie
