Rottner PS310/E01 Manuel utilisateur

Electronic lock PS310/E01, PS310/ES01, PS310/E02 Instructions

www.rottner-tresor.at

Ver. 1/2 01-2019

ELECTRONIC LOCK

PS310/E01, PS310/ES01, PS310/E02

INSTRUCTIONS

1OPERATING UNIT

Fig. 1.1

1 - keyboard *, 2 - folding handle, 3 - green LED [G],

4 - red LED [R], 5 - contacts for emergency power supply

2GENERAL INFORMATION

2.1 Master code [PIN1]

Number combination (6 to 8 digits) to open the

electronic lock and the authorized code for making the

settings.

When you put your safe into operation, change the

factory master code (see section 4.1) to a personal

master code. Test the master code you have stored

several times before storing valuables in your safe.

Factory-master code:

1–2–3–4–5–6

2.2 User code [PIN2]

Number combination (6 to 8 digits) to open the

electronic lock and to make limited settings.

The electronic lock has no user code active from the

factory. To activate a user code, follow the procedure

described in section 4.2.

2.3 Signals

[G]1Short acoustic signal and green LED light

up once (3) - confirmation when pressing a key on the

keyboard (1).

[G]2Short double-beep and two green LED

light up (3) - confirmation of a correct entry(eg: code).

[R]-- Long acoustic signal and red LED (4)

flashes once - error message (eg: wrong code).

[R]5Short simple acoustic signal and five red

LED light up (4) –Warning: Battery Low. See point

5..1 Battery change.

* For variants of the keyboard, use the «#» key instead

of the «Enter» key to confirm the entry.

3Open / Close

3.1 Opening the electronic lock

3.1.1 Opening with the factory master code

[ON][1][2][3][4][5][6][Enter*]

3.1.2 Opening with a personal master code

[ON][PIN1][Enter*]

3.1.3 Opening with user code

[ON][PIN2][Enter*]

3.1.4 Opening with a dual-function code

[ON][1-9 (User)][Enter*]

[PIN2][Enter*]

[1-9 (User)][Enter*]

[PIN3][Enter*] –within 1 Minute

After correctly entering the first code [PIN2] [Enter],

the second code [PIN3] [Enter] must be entered

within 1 minute, while the green LED [



G]1 (see point

2.3) lights up every 5 seconds.

3.1.5 Opening with the time delay

[ON][PIN1 oder PIN2][Enter*]

[Wait for the programmed time delay]

[PIN1 oder PIN2][Enter*]

[PIN1 or PIN2] must be entered again while the

programmed opening window is active.

After the time delay expires an alarm sounds.

If the [Enter] key is pressed during the opening delay,

the opening delay is canceled and the opening must be

restarted.

After entering a correct code, the green LED (3)

lights up briefly and you can open the electronic lock

by turning the hinged handle (2) clockwise to the right

within 5 seconds.

Electronic lock PS310/E01, PS310/ES01, PS310/E02 Instructions

www.rottner-tresor.at

Ver. 1/2 01-2019

If an incorrect code is entered three times consecutively,

the electronic lock is locked for five minutes. During this

blocking period, the red LED (4) lights up regularly and the

electronic lock can not be operated.

3.2 Closing

Close the door and rotate the handle (2)

counter-clockwise to the left until it stops. Check to be

sure your safe is correctly closed.

4Programming

It is recommended to make changes (code change,

...) only with the door open.

After a code change, test the code you have stored

several times with the door open before closing your

safe.

The electronic lock can not be programmed if the

power supply is too low, as indicated by the "Battery

Low" warning - see section 2.3 [R]5

4.1 Changing the master code [PIN1]

[ON] [Enter] [1] [Enter] [PIN1] [Enter]

[New PIN1] [Enter]

[Repeat New PIN1] [Enter]

Test the new master code several times with the door

open:

[ON][New PIN1][Enter]

4.2 4.2 Activating and changing the user code

[PIN 2] with the master code [PIN1]

Before a user code [PIN2] can be activated, the

master code [PIN1] must be changed from the factory

settings to a personal master code [PIN1] (see

section 4.1).

[ON][Enter][2][Enter] [1-9 (User

number)][Enter][PIN1][Enter] [New

PIN2][Enter]

[Repeat the new PIN2] [Enter]

Test the new user code several times with the door

open:

[ON][New PIN2][Enter]

4.3 Change user code [PIN2] without master

code

[ON][Enter][3][Enter]

[1-9 User number)][Enter][PIN2][Enter]

[New PIN2][Enter]

[repeat the new PIN2] [Enter]

Test the new user code several times with the door

open:

[ON][New PIN2][Enter]

4.4 Delete user - ONLY possible with master

code

[ON][Enter][0][Enter][1-9 (User

number)][Enter][PIN1][Enter]

4.5 4.5 Enable the dual-code function

Before you can activate the dual-code function,

at least one user code [PIN2] must be activated,

see section 4.2.

When dual-code function is activated, two

codes must be entered for the opening.

[ON][Enter][7][Enter][PIN1][Enter]

4.6 Disabling the dual code function

[ON][Enter][8][Enter][PIN1][Enter]

4.7 Enable the time delay

[ON] [Enter] [6] [Enter] [PIN1] [Enter]

[01-99 –Time delay in Minutes] [1-9 –

opening window in minutes] [Enter]

z. B. 092 = 9 minutes opening delay and 2

minutes opening window

Test the opening delay with the door open.

4.8 Disable the time delay

[ON] [Enter] [6] [Enter] [PIN1] [Enter]

[000] [Enter]

4.9 Enable / Disable of the acoustic signals

[ON] [Enter] [5] [Enter] [PIN1] [Enter]

Electronic lock PS310/E01, PS310/ES01, PS310/E02 Instructions

www.rottner-tresor.at

Ver. 1/2 01-2019

5Baterry change / external power supply

5.1 Battery Replacement

The battery is located on the inside of the door.

According to the lock model, a battery holder as

shown (Fig.5.1a) is shown or installed below

(Fig.5.1b)

Remove the battery cover (see Fig. 5.1a) or pull

out the battery holder (see Fig. 5.1b)

Fig. 5.1 a. b.

Insert a new high quality 9-volt battery.

(Do not use rechargeable batteries or

non-alkaline batteries).

Close the battery holder.

5.2 Opening with an external power supply

Take a new high quality 9 Volt battery..

Hold the battery on the two contacts (see Fig.

5.2). Pay attention to the correct polarity when

inserting the battery !!

Fig.5.2

Enter an access-authorization code [PIN1]or

[PIN2] .

Turn the handle (2) clockwise to the right within

5 seconds.

Remove the battery from the contacts and

replace the battery on the inside of the door

(see Fig. 5.1).

Ce manuel convient aux modèles suivants

Autres manuels Rottner Verrouillage

Rottner

Rottner EM2020 Manuel utilisateur

Manuels Verrouillage populaires d'autres marques

Magic

Magic 105 Manuel utilisateur

Gantner

Gantner GAT NET.Lock 7020 System Guide rapide

Wittkopp

Wittkopp Insys 7202 Manuel utilisateur

Dorma

Dorma Studio Classic Manuel utilisateur

Securam

Securam ECSL-601 Manuel utilisateur

Sudhaus

Sudhaus 3003 Manuel utilisateur

Safety 1st

Safety 1st 48517 Manuel utilisateur

Pado

Pado FDS-10 Manuel utilisateur

Esco

Esco systeQ Series Manuel utilisateur

COMPX

COMPX National D8951 Manuel utilisateur

secureo

secureo Key Box Manuel utilisateur

Stock Loks

Stock Loks C8713 Manuel utilisateur

COMPX

COMPX 1T-058 Manuel du propriétaire

Auslock

Auslock T11 Manuel utilisateur

ELCOM

ELCOM 7205 Manuel utilisateur

Stealth SAFES

Stealth SAFES ShadowVault Manuel utilisateur

Knox

Knox KeySecure 5 Manuel utilisateur

Kwikset

Kwikset 48334/01 Manuel utilisateur