Roswell SUPRA Pro Edge Tower Guide de démarrage rapide
Rev. 15-Oct-15 Pg. 1/14
www.roswellwakeair.com
If you have any questions please call : 1-855-962-WAKE(9253)
Information: info@roswellwakeair.com
Warranty: warranty@roswellwakeair.com
Contents of Bimini Box
Pro Edge Tower
Bimini Installation
Instructions
Tools Required
5/16" Allen Key
3/16" Allen Key
THREADLOCKER
Phillips Screwdriver
RED
Roswell recommends 2 people for installation of the bimini.
Drill
9/64” Drill Bit
x4 x2 x6
Pivot
Washer x2
Bimini Frame,
Canvas, Clips
and Boot
Center Punch
Marker
2 inch Low Tack
Masking Tape
Utility Knife
x2
***Important***
Read & follow these installation instructions carefully. Failure to do so may result in an improper
bimini installation. Damage to parts due to improper bimini installation is not covered under warranty.
10-24 UNC Tap
Towers and tower accessories require regular maintenance. Tower hardware and retaining bolts can become loose with normal
operation; it is owner’s responsibility to ensure all hardware is kept tight and secure. Corrosion and/or oxidation on coated
surfaces as well as on all hardware are specifically excluded from warranty as their care, maintenance, and environments of use
cannot be controlled by Roswell Wake Air. Damage due to misuse or improper care is also excluded from warranty. For full
warranty details please contact your local dealer.
Shim
Washer x4
Plastic
Washer x4
5/16” Drill Bit
1/2-13 x 1.50”
Attention
Installing your bimini clips in
freezing or near freezing
temperatures is NOT
recommended. Failure to
do so will result in broken
bimini clips. Damage to
parts from improper use is
not covered under warranty.
Port Bimini Arm
Starboard Bimini Arm
A
B
Pg. 2/14
Remove the 4 rubber plugs from the bimini mounts
on your tower. These are press fit into the bimini
mounts and do not require any tools to remove.
Rubber
Plugs
Preparing your tower
Installing Bimini Arms
Bimini
mounts
x4
Remove the 2 bimini arms from your box. Carefully unwrap them. Assemble the bimini arms to the tower using
the 4 bolts and 4 plastic washers. Apply red Loctite to all 4 bolts and assemble the arms as illustrated. Do
not fully tighten down the arms yet, they need to be loose for the next installation step.
Bolts
REKCOLDAERHT
5/16"
Plastic
Washers
C
Tighten down the
bimini arm bolts that
were loosely installed
in Step B.
Tighten Bimini Arm
Bolts
5/16"
**IMPORTANT**
Tighten the Rear
Bolts at the top of the
slots as illustrated.
Port Bimini Arm
Starboard Bimini Arm
E
Unzip the bimini boot from the bimini frame. Unroll
your fabric, clips and middle bow. Rotate the
frame upwards and insert the quick release pins
into the arms only. Clip all 6 clips onto the rear
tower tube.
F
Apply a strip of 2 inch low
tack masking tape along the
entire rear tower tube from
bimini arm to bimini arm.
The strip should cover the
portion of rear tube that
faces the interior of the boat.
This step is essential to
avoid any accidental
scratches to the tower paint.
Pg. 3/14
Bimini Boot Removal
Bimini Boot
Low tack masking tape
2 inch Low Tack
Masking Tape
Rear Tube
***IMPORTANT***
D
THREADLOCKER
3/16"
Bimini Frame Assembly
x2
Remove the plastic wrapping from your
bimini frame. Grab the 2 shoulder
bolts, 2 pivot washers, and 2 shoulder
bolt washers from your bimini box.
Apply red Loctite to the 2 bolts. Attach
the bimini frame to the bimini arms as
illustrated. Make sure the pivot wash-
ers are sandwiched between the bimini
arms and the bimini frame and that the
shoulder bolt washers are under the
heads of the shoulder bolts. Insert the
folding quick release pins.
x2
**This step requires 2 people**
***To avoid installing the frame upside down make sure
the middle bow bimini hinges are facing upward***
Shoulder Bolt
Pivot Washer
Folding Quick Release Pin
Shoulder Bolt Washer
(These may already be installed in your frame)
x2
Position :
- Bimini is in use.
- For initial Installation of
bimini clip harware
Position :
- For clipping or
unclipping bimini clips
If you plan to clip/unclip the bimini clips, your bimini frame
must be rotated upwards with the quick release pins in the
ARMS ONLY.
**Refer to page 14 for Alignment Tip & Tricks**
G
H
Pg. 4/14
I
Start with the
2 center clips
illustrated.
With the top surface of each clip parallel to the top
of the tower, use a marker to mark the center mark
for each bimini clip. Remove each center clip from
the rear tower tube so they are out of the way of the
center mark.
Center punch the 2 marker points on
the masking tape.
2 inch Low Tack
Masking Tape
Fabric-Clips Installation:
Step 2
Fabric-Clips Installation:
Step 3
Marker Point
Snap the 6 bimini clips around the rear tube of the tower
as illustrated. Adjust the bimini clip locations until they are
symmetrical and the fabric is tight and wrinkle free.
Rear Tower Tube Center Bimini Clips
Fabric-Clips Installation:
Step 1 Bird’s Eye View
**IMPORTANT**
The position of the
center Clips is the
most important to
begin with. Make sure
that the clips are
positioned along the
rear tower tube so
that the fabric is
centered around the
Light Housing.
Light Housing
Center Clips
Prior to marking the center points for the 2 center clips in Step I, it is
important to pull/rotate the clips until the clip top surface is parallel to
the top of the tower. With a good grasp on each clip, rotate them until
the top is parallel then mark the center point with a black marker.
Make sure your fabric stays centered around the light housing
Side View
Top View
2 inch Low Tack
Masking Tape
J
Pg. 5/14
K
L
Fabric-Clips Installation:
Step 4
Fabric-Clips Installation:
Step 5
Using a cordless drill and a 9/64” drill bit, drill holes
through the tower where you made the 2 center
punch marks. Using a tap and a 10-24 UNC bit,
carefully tap each of the holes you just drilled.
***When drilling the holes
for your bimini clip it is
important to drill the
holes perpendicular to
the location of the hole to
be drilled. This will allow
for an optimal fit of the
bimini clip.***
Side View
Center Punch Mark
x2
Remove the masking around the 2 newly drilled
holes only. Mount the 2 trimmed clip locators to the
newly drilled and tapped holes with 2 of the
provided bimini clip bolts from your bimini box.
Apply a small amount of red Loctite to each bolt.
Using a Phillips screwdriver, attach the bimini clip
locators to the tower.
Do not overtighten these screws.
9/64” Drill Bit
THREADLOCKER
2 inch Low Tack
Masking Tape
2: Grab a sharp utility knife and carefully cut away the
locator posts on each bimini clip and locator. There are 6
posts on each bimini clip and locator. When trimming the
posts always cut away from yourself and the tower.
Trimming the locator
posts
Locator Posts
***Clips are attached to the bimini Canvas. Bimini
Canvas is not illustrated for image clarity***
Side View
Clip Locator
Push and Break
1: Push and break off the clip locator from
the 2 center bimini clips.
N
Pg. 6/14
O
Middle Clips
Outer Clips
Repeat Steps H, I, J, K & L for the
2 outer bimini clips illustrated
Be sure to pull the outer bimini clips away from the newly
installed middle clips prior to marking the center points.
Remember to rotate the outer clips until the clip top
surface is parallel with the tower geometry.
M
x2
Fabric-Clips Installation:
Step 6
9/64” Drill Bit
This is how your 6 bimini
clips now look
Clip Locators
Rear tower tube
This is how the locators will look on the tower.
How your Bimini Clips
now look
***Clips are attached to the bimini
Canvas. Bimini Canvas is not
illustrated for image clarity***
Repeat Steps H, I, J, K & L for the 2
middle bimini clips illustrated
Be sure to pull the middle bimini clips away from the
newly installed center clips prior to marking their center
points. Remember to rotate the middle clips until the
clip top surface is parallel with the top of the tower.
Center Clips
Middle Clips
x2
Fabric-Clips Installation:
Step 6
9/64” Drill Bit
THREADLOCKER
Q
Pg. 7/14
R
2 : Re-clip all of your bimini clips to the
tower. Use the finger tab to flex the clips over
the tubing.
Folding Quick
Release Pin
Insert the 2 folding quick release pins through the
frame and bimini arms to lock your bimini frame in
place. Loop the 4 Bimini fabric loops around the
frame and Velcro.
Final Step
P
Your bimini is now ready
for use.
Happy Boating!!
1 : Remove the folding quick release pins. Rotate the
frame upwards and insert the quick release pins into the
bimini arm only. This will hold the frame in an up position
and reduce tension on the bimini clips. This step is
required to properly clip and unclip the bimini clips.
Re-Clip Bimini Clips
Do not apply excessive force when flexing the clips.
***Important***
Read & follow these instructions carefully. Failure to do so may result in damage to parts.
Damage to parts from improper use is not covered under warranty.
Pg. 8/14
www.roswellwakeair.com
If you have any questions please call : 1-855-962-WAKE(9253)
Information: info@roswellwakeair.com
Warranty: warranty@roswellwakeair.com
Pro Edge Tower
Bimini Owners Manual
Attention
Using your bimini clips in freezing or near freezing temperatures is NOT recommended.
Failure to do so will result in broken bimini clips. Damage to parts from improper use is
not covered under warranty.
A
Pg. 9/14
Unfolding your Pro Edge Tower Bimini
5 : Remove your 2 quick release pins from your bimini arms. Pull down lightly on the bimini frame
and re-insert the quick release pins through the bimini frame and arms. Loop the 4 Bimini fabric
loops around the frame and Velcro. Your Bimini is ready to use.
Bimini Boot
1 : Undo the 2 straps that secure the bimini to your tower.
Tie down straps
3 : Rotate the frame upwards and insert the quick
release pins into the bimini arm only. Rotate the bimini
frame down until it rests on the quick release pins as
illustrated
4 : Clip all of your bimini clips to the tower. Use the finger
tab to flex the clips over the tubing.
2 : Unfold the frame from the tower. Unzip the bimini
boot from the bimini frame. Unroll your fabric, clips and
middle bow.
Folding Quick
Release Pin
B
Pg. 10/14
Folding up your Pro Edge Tower Bimini
1 : Remove your 2 folding quick release pins and
undo the 4 Velcro loops.
3 : Unclip all of your bimini clips from
the rear tower tube. 4 : Remove the quick release pins and lower the frame.
Fold the middle bow toward the front bow and wrap the
fabric and clips around both bows. Zip the bimini boot over
the bows and fabric.
5 : Fold the bimini towards the tower until it rests on top of
the tower. 6 : Loop the tie
down straps over
and under the front
tower tube. Adjust
the straps to tighten
the bimini to the
tower.
2 : Rotate the frame upwards and insert the
quick release pins into the bimini arm only.
Folding Quick
Release Pin
Tie down straps
Bimini Boot
Table des matières
Autres manuels Roswell Équipement nautique
Manuels Équipement nautique populaires d'autres marques
Dowco
Dowco V322 CC - 2019 Manuel utilisateur
Humphree
Humphree HCS-5 Manuel utilisateur
Vetus
Vetus BOW4512D Fiche technique
Dock Doctors
Dock Doctors SLIDING BOARDING STEP Manuel utilisateur
Mastervolt
Mastervolt Mass Combi 12/2000-100 Instructions d'utilisation d'origine
Zattini Group
Zattini Group bamar BOXTRON E14S Guide de l'utilisateur
